This DTC is applicable to models w/ tumble control valve.
The ECM activates the DC motor for the intake air control valve actuator (for tumble control valve), which opens and closes the Tumble Control Valve (TCV). The ECM activates the DC motor based on engine speed, coolant temperature, intake air temperature and other conditions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2009 | Intake Manifold Runner Control Circuit Low (Bank 1) | Both of the following conditions continue for 1 second (1 trip detection logic).
(a) The output duty of the intake air control valve actuator is 34% or higher. (b) The current of the intake air control valve actuator is less than 0.35 A. |
·
Open or short in intake air control valve actuator (for tumble control valve) circuit ·
Intake air control valve actuator (for tumble control valve) ·
Intake manifold ·
ECM |
Comes on | DTC stored |
| P2010 | Intake Manifold Runner Control Circuit High (Bank 1) | Either of the following conditions continues for 6 times or more (1 trip detection logic).
(a) The motor drive IC has overcurrent. (b) The motor drive IC overheats. |
·
Open or short in intake air control valve actuator (for tumble control valve) circuit ·
Intake air control valve actuator (for tumble control valve) ·
Intake manifold ·
ECM |
Comes on | DTC stored |
When the voltage of the intake air control valve actuator deviates from the standard range, the ECM determines that a malfunction has occurred and stores a DTC.
| Required Sensors/Components (Main) | Intake air control valve actuator (for tumble control valve) |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Check that the engine coolant temperature is 60°C (140°F) or higher.
Wait approximately 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2009 or P2010.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P2004.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P2004
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Inspect the intake air control valve actuator (for tumble control valve).
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>REMOVAL
Inspect the intake manifold for the tumble control valve operation.
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after replacing the intake manifold.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the intake air control valve actuator connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Y2-4 (M-) - E26-24 (IA1-) | Always | Below 1 Ω |
| Y2-5 (M+) - E26-25 (IA1+) | Always | Below 1 Ω |
| Y2-4 (M-) or E26-24 (IA1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Y2-5 (M+) or E26-25 (IA1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Wait approximately 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2009 or P2010 is output | A |
| DTC is not output | B |
A
B