Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER › from 2016.05
RM19V0EQ _52 Drivetrain _014586 AXLE AND DIFFERENTIAL _0074015 REAR AXLE CARRIER A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42305 1.INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

a.

Install the rear axle carrier sub-assembly to the rear shock absorber assembly with the 2 bolts and 2 nuts.

Torque:
180 N*m (1835 kgf*cm, 133 ft.*lbf)

NOTICE:

While keeping the bolts from rotating, tighten the nuts.



Hide 48720A 2.TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.

Temporarily tighten the rear No. 1 suspension arm assembly (outer side) to the rear axle carrier sub-assembly with the bolt and nut.

NOTICE:

When temporarily tightening the bolt, keep the nut from rotating.


HINT:

Insert the bolt from the front of the vehicle.



Hide 48740F 3.TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Temporarily tighten the rear No. 2 suspension arm assembly (outer side) to the rear axle carrier sub-assembly with the bolt and nut.

NOTICE:

When temporarily tightening the bolt, keep the nut from rotating.


HINT:

Insert the bolt from the rear of the vehicle.



Hide 48780A 4.TEMPORARILY TIGHTEN REAR STRUT ROD ASSEMBLY

a.

Temporarily tighten the rear strut rod assembly (rear side) to the rear axle carrier sub-assembly with the bolt and nut.

NOTICE:

When temporarily tightening the bolt, keep the nut from rotating.


HINT:

Insert the bolt from the inside of the vehicle.



Hide 42450B 5.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

Hide 89516D 6.CONNECT SKID CONTROL SENSOR WIRE

Hide 42431 7.INSTALL REAR DISC

Hide 42491 8.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 9.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Hide 10.STABILIZE SUSPENSION

a.

Install the rear wheel.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


b.

Lower the vehicle and bounce it up and down several times to stabilize the rear suspension. Raise the vehicle.


c.

Remove the rear wheel.


Hide 48720A 11.FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.

Fully tighten the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

NOTICE:

Since a stopper nut is used, fully tighten the bolt.



Hide 48740F 12.FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Fully tighten the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

NOTICE:

Since a stopper nut is used, fully tighten the bolt.



Hide 48780A 13.FULLY TIGHTEN REAR STRUT ROD ASSEMBLY

a.

Fully tighten the bolt

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)

NOTICE:

Since a stopper nut is used, fully tighten the bolt.



Hide 14.ADJUST PARKING BRAKE

Hide 15.INSTALL REAR WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 16.INSPECT AND ADJUST REAR WHEEL ALIGNMENT