Home › Engine / Hybrid System › 2AR-FE INTAKE / EXHAUST › INTAKE MANIFOLD › from 2016.05
RM19V0EQ _51 Engine / Hybrid System _014577 2AR-FE INTAKE / EXHAUST _0073948 INTAKE MANIFOLD A

2AR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.

Install the wire harness clamp bracket to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
A292928C02
0.854,1.719 0.99,1.719 0.99,1.719 1.208,1.438 true 0.677,1.625 0.99,1.781 0.313,0.156 10 *a
*a Black


Connect the 2 vacuum hoses and check that the No. 1 check valve is installed as shown in the illustration.


c.

w/ TCV:

i.

Check the 4 tumble control valves (TCV).

NOTICE:

The 4 tumble control valves (TCV) may be damaged if they are not closed before installing the intake manifold.


HINT:

Connect the battery to the terminals of the intake air control valve actuator (for TCV) to operate the motor and close the 4 tumble control valves (TCV).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION




d.

Install a new intake manifold gasket to the intake manifold.


e.

Temporarily install the intake manifold with the 6 bolts.


f.
A381763C02
0.083,0.083 0.427,0.458 0.344,0.375 12 false *A 0.083,2.406 0.406,2.708 0.323,0.302 12 false *B 1.771,0.49 1.927,0.708 0.156,0.219 10 true 1 1.792,2.625 1.979,2.833 0.188,0.208 10 false 1 1.01,0.208 1.167,0.406 0.156,0.198 10 false 2 1.031,2.375 1.188,2.573 0.156,0.198 10 false 2 2.51,0.188 2.667,0.385 0.156,0.198 10 false 3 2.51,2.354 2.667,2.552 0.156,0.198 10 false 3 3.167,3.594 3.323,3.792 0.156,0.198 10 true 4 3.135,1.448 3.292,1.646 0.156,0.198 10 true 4 0.323,3.198 0.458,3.406 0.135,0.208 10 true 5 0.354,0.76 0.49,0.969 0.135,0.208 10 false 5 0.531,2.188 0.667,2.396 0.135,0.208 10 false 6 0.542,4.344 0.677,4.552 0.135,0.208 10 false 6
*A w/o TCV
*B w/ TCV


Tighten the 6 bolts in the order shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


g.

w/ TCV:

i.
A381764C01
0.083,0.083 0.521,0.427 0.438,0.344 12 false *A 0.115,2.49 0.427,2.802 0.313,0.313 12 false *B
*A w/o TCV
*B w/ TCV


Connect the intake air control valve actuator (for TCV) connector.



h.

Engage the 2 wire harness clamps.


i.

Connect the wire harness with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


j.
A254751

Install the wire harness clamp bracket to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


k.

Connect the sensor wire connector.


l.

Engage the 3 wire harness clamps.


m.

Connect the fuel vapor feed hose to the intake manifold and slide the clip to secure it.


n.

Install the 2 wire harness clamp brackets to the intake manifold with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23814B 2.INSTALL FUEL DELIVERY PIPE

Hide 23901 3.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 44774 4.CONNECT UNION TO VACUUM TUBE HOSE (for LHD)

a.

Connect the union to vacuum tube hose to the intake manifold and slide the clip to secure it.


Hide 44773F 5.CONNECT UNION TO CHECK VALVE HOSE (for RHD)

a.

Connect the union to check valve hose to the intake manifold and slide the clip to secure it.


Hide 12262 6.CONNECT NO. 2 VENTILATION HOSE

a.

Connect the No. 2 ventilation hose to the intake manifold and slide the clip to secure it.


Hide 17650 7.INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

a.

Install the vacuum switching valve assembly (for ACIS) to the intake manifold with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.

Connect the vacuum switching valve assembly (for ACIS) connector.


c.

Connect the 2 vacuum hoses.


d.

Engage the wire harness clamp.


e.

for LHD:

i.

Connect the union to vacuum tube hose to the vacuum hose clamp.



f.

for RHD:

i.

Connect the union to check valve hose to the vacuum hose clamp.



Hide 22030 8.INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 55702A 9.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55702A 10.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 11.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 12.CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION