Home › Engine / Hybrid System · 1AZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The camshaft position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed onto the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft timing rotor passes through the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.

DTC No.
DTC Detection Condition
Trouble Area
P0340
When one of the following conditions is met:
  1. A missing camshaft position sensor signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).
  2. No camshaft position sensor signal to the ECM at an engine speed of 600 rpm or higher (1 trip detection logic).
  3. No camshaft position sensor signal to the ECM while cranking (2 trip detection logic).
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. Intake camshaft
  4. Valve timing
  5. ECM
  1. Reference: Inspection using an oscilloscope .

MONITOR DESCRIPTION

If no signal is transmitted by the camshaft position sensor despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Required Sensors/Components (Main)
Camshaft position sensor
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine and ECT / DTC.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0340.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)
  1. Inspect the camshaft position sensor (Click here).



NG
REPLACE CAMSHAFT POSITION SENSOR (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E82-1 (G2) - E83-99 (G2+)
    Always
    Below 1 Ω
    E82-2 (G-) - E83-98 (G2-)
    Always
    Below 1 Ω
    E82-1 (G2) or E83-99 (G2+) - Body ground
    Always
    10 kΩ or higher
    E82-2 (G-) or E83-98 (G2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)


    BR03795E17
  1. Check the camshaft position sensor installation condition.

    OK:
    Camshaft position sensor is installed correctly.



NG
SECURELY REINSTALL CAMSHAFT POSITION SENSOR (Click here)
OK


4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
  1. Inspect the timing rotor of the intake camshaft.

    OK:
    Camshaft timing rotor does not have any cracks or deformation.



NG
REPLACE INTAKE CAMSHAFT (Click here)
OK


5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
A146275E03
  1. Remove the cylinder head cover sub-assembly.

  1. Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are aligned with the front marks located on the No. 1 and No. 2 bearing caps as shown in the illustration.

    HINT:
    If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

    OK:
    Timing marks on camshaft timing gear assembly and camshaft timing sprocket are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark
    *2
    Front Mark
    *3
    Groove



NG
ADJUST VALVE TIMING (Click here)
OK


6.REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0340 is output
    A
    DTC is not output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
END
A

REPLACE ECM (Click here)