Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > ECM Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
Either condition is met:
  1. "ECM (Engine)" is not displayed on the "Communication Bus Check" screen of the intelligent tester (Click here)
  2. Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table" (Click here)
  1. Power source circuit of ECM
  2. ECM main line or connector
  3. ECM ground circuit
  4. ECM

WIRING DIAGRAM


C248925E11


C244443E19


C241658E06


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, wait at least 20 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.
  6. After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C248926E07
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for 2GR-FE or 2AR-FE):
    Tester Connection
    Condition
    Specified Condition
    A25-13 (CANH) - A25-26 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Standard Resistance (for 1AZ-FE):
    Tester Connection
    Condition
    Specified Condition
    A74-41 (CANH) - A74-49 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *A
    for 2GR-FE or 2AR-FE
    *B
    for 1AZ-FE
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)
OK


2.CHECK ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit.
    for 2GR-FE: Click here
    for 2AR-FE: Click here
    for 1AZ-FE: Click here

Result:
Result
Proceed to
OK (for 2GR-FE)
A
OK (for 2AR-FE)
B
OK (for 1AZ-FE)
C
NG
D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
A

REPLACE ECM (Click here)