DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) |
DTC P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0016 | Deviation in crankshaft position sensor signal and camshaft position sensor (for intake camshaft) signal (2 trip detection logic). |
|
| P0017 | Deviation in crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic). |
|
| Related DTCs | P0016: Camshaft timing misalignment at idling (for intake camshaft) P0017: Camshaft timing misalignment at idling (for exhaust camshaft) |
| Required Sensors/Components (Main) | Camshaft timing gear assembly Camshaft timing exhaust gear assembly |
| Required Sensors/Components (Related) | Camshaft position sensor Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | Within 1 minute |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0010 (VVT oil control valve) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) |
| Engine speed | 500 to 1000 rpm |
| Monitor runs whenever the following DTCs are not stored | P0013 (Exhaust VVT oil control valve) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) |
| Engine speed | 500 to 1000 rpm |
| Either of the of following conditions is met | - |
| VVT learned value at maximum retarded valve timing | Less than 22°CA (crankshaft angle) |
| VVT learned value at maximum retarded valve timing | More than 47°CA (crankshaft angle) |
| Either of the of following conditions is met | - |
| VVT learned value at maximum advanced valve timing | Less than 82.5°CA (crankshaft angle) |
| VVT learned value at maximum advanced valve timing | More than 107.5°CA (crankshaft angle) |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 AND P0017) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0016 or P0017 is output | A |
| DTC P0016 or P0017 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the A/C on.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 1) / Gas Valve Control / VVT Change Angle #1, VVT Ex Chg Angle #1.
Perform the Active Test. Check that the displacement angle varies.
|
| ||||
| OK | |
| 3.ADJUST VALVE TIMING |
Adjust the valve timing (Click here).
|
| ||||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for intake or exhaust camshaft) (Click here).
|
| ||||
| OK | |
| 5.INSPECT OIL CONTROL VALVE FILTER |
Remove the oil control valve filter .
Check that the filter is not clogged.
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Replace the camshaft timing gear assembly or camshaft timing exhaust gear assembly (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0017) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0016 or P0017 is output | B |
|
| ||||
| A | ||
| ||