DTC P0335 Crankshaft Position Sensor "A" Circuit |
DTC P0339 Crankshaft Position Sensor "A" Circuit Intermittent |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0335 | One of the following conditions is met (1 trip detection logic):
|
|
| P0339 | All of the following conditions are met (1 trip detection logic): (a) The engine speed is 1000 rpm or higher. (b) No crankshaft position sensor signal for 0.05 seconds or more. (c) 3 seconds or more have elapsed since the starter signal switched from on to off. |
|
![]() |
| ECM Terminal Name | Between NE+ and NE- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
| Related DTCs | P0335: Crankshaft position sensor range check/rationality P0335: Crankshaft position sensor verify pulse input |
| Required Sensors/Components (Main) | Crankshaft position sensor |
| Required Sensors/Components (Related) | Camshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | -: Verify pulse input case 1 4.7 seconds: Verify pulse input case 2 0.016 seconds: Range check/rationality |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Ignition switch | ON |
| Time after starter off to on | 3 seconds or more |
| Number of camshaft position sensor signal pulses | 6 times |
| Battery voltage | 7 V or higher |
| Minimum battery voltage while starter on | Less than 11 V |
| Camshaft position sensor circuit fail | Not detected |
| All of the following conditions are met | - |
| Starter | Off |
| Engine speed (Top dead center) | 600 rpm or higher |
| Engine speed (30°CA) | 600 rpm or higher |
| Time after starter from on to off | 3 seconds or more |
| Both of the following conditions are met | - |
| Starter | On |
| Minimum battery voltage while starter on | Below 11 V |
| Number of crankshaft position sensor signal pulses | 132 times or less, or 174 times or more |
| Engine speed signal | No signal |
| Crankshaft position sensor |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (ENGINE SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.
Start the engine.
Read the values displayed on the Techstream while the engine is running.
|
| ||||
| OK | ||
| ||
| 2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE) |
Inspect the crankshaft position sensor (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E72-1 (NE) - E26-76 (NE+) | Always | Below 1 Ω |
| E72-2 (NE-) - E26-109 (NE-) | Always | Below 1 Ω |
| E72-1 (NE) or E26-76 (NE+) - Body ground | Always | 10 kΩ or higher |
| E72-2 (NE-) or E26-109 (NE-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() |
Check the crankshaft position sensor installation.
|
| ||||
| OK | |
| 5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE) |
Inspect the teeth of the crank angle sensor plate.
|
| ||||
| OK | ||
| ||