Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P101D    A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

HINT:
  1. When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
  2. Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  3. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.

  4. The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.


    A255119E02


DTC No.
DTC Detection Condition
Trouble Area
P0031
Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
  1. Open in air fuel ratio sensor (sensor 1) heater circuit
  2. Air fuel ratio sensor (sensor 1)
  3. No. 1 integration relay
  4. ECM
P0032
Air fuel ratio sensor heater current reaches the high limit
(Hybrid IC high current limiter monitor input "Fail") (1 trip detection logic).
  1. Short in air fuel ratio sensor (sensor 1) heater circuit
  2. Air fuel ratio sensor (sensor 1)
  3. No. 1 integration relay
  4. ECM
P101D
The heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
ECM

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.
The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.
When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY


Related DTCs
P0031: Air fuel ratio sensor heater range check (low current)
P0032: Air fuel ratio sensor heater range check (high current)
P101D: Air fuel ratio sensor heater performance
Required Sensors/Components (Main)
Air fuel ratio sensor heater
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
10 seconds: P0031
10.24 seconds: P0032
1 second: P101D
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None

P0031 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Time after heater on
5 seconds or more
Active heater off control
Not operating
Active heater on control
Not operating
Air fuel ratio sensor heater performance fail (P101D)
Not detected
Heater output duty cycle
30% or higher

P0032 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Time after heater on
5 seconds or more
Heater output duty cycle
Higher than 0%
Active heater off control
Not operating
Active heater on control
Not operating
Air fuel ratio sensor heater high current counter
1.024 seconds or more
Active heater off control counter for high current
0.512 seconds or more

P101D 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Time after heater on
5 seconds or more
Air fuel ratio sensor heater low current fail (P0031)
Not detected
Air fuel ratio sensor heater duty cycle
10% or higher, and less than 60%
Air fuel ratio sensor heater on current
0.8 A or higher
Active heater off control
Not operating
Active heater on control
Not operating

TYPICAL MALFUNCTION THRESHOLDS


P0031 
Air fuel ratio sensor heater on current
Less than 0.8 A

P0032 
Both of the following conditions are met
-
Air fuel ratio sensor heater output
On
Hybrid IC high current limiter monitor input
Fail

P101D 
All of the following conditions are met
-
Hybrid IC high current limiter monitor input
Fail
Air fuel ratio sensor heater off current
Higher than 11 A
Active heater off control for on stuck
Operating

COMPONENT OPERATING RANGE


P0031 
Air fuel ratio sensor heater on current
0.8 A or higher

P0032 
Both of the following conditions are met
-
Air fuel ratio sensor heater output
On
Hybrid IC high current limiter monitor input
Pass

P101D 
Air fuel ratio sensor heater off current
11 A or less

CONFIRMATION DRIVING PATTERN


A262623E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0031, P0032 or P101D.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A266344E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Refer to "Data List / Active Test" [A/F Heater Duty #1] (Click here).
  2. Sensor 1 refers to the sensor closest to the engine assembly.
  3. Sensor 2 refers to the sensor farthest away from the engine assembly.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  5. Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)


    A194092E35
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E19-1 (HA1A) - E26-23 (HA1A)
    Always
    Below 1 Ω
    E19-1 (HA1A) or E26-23 (HA1A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0031, P0032 or P101D is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E19-2 (+B) - 1A-7
    Always
    Below 1 Ω
    E19-2 (+B) or 1A-7 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)


    A256530E02
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1D-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)