DTC B1782 Rear Occupant Classification Sensor LH Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1782 |
|
|

| 1.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the occupant detection ECU and rear occupant classification sensor LH.
Disconnect the connectors from the occupant detection ECU and rear occupant classification sensor LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT WIRE RH (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| d8-1 (SVC3) - Body ground | Ignition switch ON | Below 1 V |
| d8-3 (SIG3) - Body ground | Ignition switch ON | Below 1 V |
| d8-5 (SGD3) - Body ground | Ignition switch ON | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| d18-1 (SVC3) - Body ground | Ignition switch ON | Below 1 V |
| d18-3 (SIG3) - Body ground | Ignition switch ON | Below 1 V |
| d18-5 (SGD3) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
| *A | for TMMK Made |
| *B | for SIA Made |
| *1 | Rear Occupant Classification Sensor LH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | |
| 3.CHECK FRONT SEAT WIRE RH (OPEN) |
![]() |
Using a service wire, connect terminals 1 (SVC3) and 3 (SGD3), and connect terminals 2 (SIG3) and 3 (SGD3) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| d8-1 (SVC3) - d8-5 (SGD3) | Always | Below 1 Ω |
| d8-3 (SIG3) - d8-5 (SGD3) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| d18-1 (SVC3) - d18-5 (SGD3) | Always | Below 1 Ω |
| d18-3 (SIG3) - d18-5 (SGD3) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *A | for TMMK Made |
| *B | for SIA Made |
| *1 | Rear Occupant Classification Sensor LH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
| *b | Front view of wire harness connector (to Rear Occupant Classification Sensor LH) |
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| d8-1 (SVC3) - d8-5 (SGD3) | Always | 1 MΩ or higher |
| d8-3 (SIG3) - d8-5 (SGD3) | Always | 1 MΩ or higher |
| d8-1 (SVC3) - d8-3 (SIG3) | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
| d18-1 (SVC3) - d18-5 (SGD3) | Always | 1 MΩ or higher |
| d18-3 (SIG3) - d18-5 (SGD3) | Always | 1 MΩ or higher |
| d18-1 (SVC3) - d18-3 (SIG3) | Always | 1 MΩ or higher |
| *A | for TMMK Made |
| *B | for SIA Made |
| *1 | Rear Occupant Classification Sensor LH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | |
| 5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND) |
![]() |
Measure the resistance according to value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| d8-1 (SVC3) - Body ground | Always | 1 MΩ or higher |
| d8-3 (SIG3) - Body ground | Always | 1 MΩ or higher |
| d8-5 (SGD3) - Body ground | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
| d18-1 (SVC3) - Body ground | Always | 1 MΩ or higher |
| d18-3 (SIG3) - Body ground | Always | 1 MΩ or higher |
| d18-5 (SGD3) - Body ground | Always | 1 MΩ or higher |
| *A | for TMMK Made |
| *B | for SIA Made |
| *1 | Rear Occupant Classification Sensor LH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | |
| 6.CHECK DTC |
Connect the connectors to the occupant detection ECU and rear occupant classification sensor LH.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in the occupant detection ECU (Click here).
Clear the DTCs stored in the airbag sensor assembly (Click here for Separate Type Yaw Rate Sensor, Click here for Built-in Type Yaw Rate Sensor).
Turn the ignition switch off.
Turn the ignition switch to ON.
Check for DTCs (Click here).
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||
| 7.CHECK OCCUPANT DETECTION ECU |
Disconnect the cable from the negative (-) battery terminal.
Replace the occupant detection ECU with a known good one (Click here).
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in the occupant detection ECU (Click here).
Clear the DTCs stored in the airbag sensor assembly (Click here for Separate Type Yaw Rate Sensor, Click here for Built-in Type Yaw Rate Sensor).
Turn the ignition switch off.
Turn the ignition switch to ON.
Check for DTCs (Click here).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Restore the occupant detection ECU that was installed for testing to its original location (Click here).
|
| ||||
| OK | |
| 8.REPLACE OCCUPANT DETECTION ECU |
Disconnect the cable from the negative (-) battery terminal.
Replace the occupant detection ECU with a new one (Click here).
Connect the cable to the negative (-) battery terminal.
| NEXT | |
| 9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).
| NEXT | ||
| ||
| 10.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH |
Disconnect the cable from the negative (-) battery terminal.
Replace the front seat frame with adjuster assembly RH (Click here for TMMK Made Manual Seat, Click here for TMMK Made Power Seat, Click here for SIA Made Manual Seat, Click here for SIA Made Power Seat).
Connect the cable to the negative (-) battery terminal.
| NEXT | |
| 11.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).
| NEXT | ||
| ||
| 12.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH |
Disconnect the cable from the negative (-) battery terminal.
Replace the front seat frame with adjuster assembly RH (Click here for TMMK Made Manual Seat, Click here for TMMK Made Power Seat, Click here for SIA Made Manual Seat, Click here for SIA Made Power Seat).
Connect the cable to the negative (-) battery terminal.
| NEXT | |
| 13.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).
| NEXT | ||
| ||