Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1793    Occupant Classification Sensor Power Supply Circuit Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification sensor power supply circuit consists of the occupant detection ECU and rear occupant classification sensors.
DTC B1793 is stored when a malfunction is detected in the occupant classification sensor power supply circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1793
  1. The occupant detection ECU receives a line short circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification sensor power supply circuit.
  2. Rear occupant classification sensor LH malfunction
  3. Rear occupant classification sensor RH malfunction
  4. Occupant detection ECU malfunction
  1. Front seat wire RH
  2. Front seat frame with adjuster assembly RH (2 rear occupant classification sensors)
  3. Occupant detection ECU

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1793 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C249055E01


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.
  2. In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

1.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Check that the connectors are properly connected to the 2 rear occupant classification sensors and occupant detection ECU.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the 2 rear occupant classification sensors and occupant detection ECU.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)


    C238380E02
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for TMMK Made: 
    Tester Connection
    Condition
    Specified Condition
    d8-1 (SVC3) - Body ground
    Ignition switch ON
    Below 1 V
    d8-2 (SVC4) - Body ground
    Ignition switch ON
    Below 1 V
    for SIA Made: 
    Tester Connection
    Condition
    Specified Condition
    d18-1 (SVC3) - Body ground
    Ignition switch ON
    Below 1 V
    d18-2 (SVC4) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.
    Text in Illustration 
    *A
    for TMMK Made
    *B
    for SIA Made
    *1
    Rear Occupant Classification Sensor LH
    *2
    Rear Occupant Classification Sensor RH
    *3
    Occupant Detection ECU
    *4
    Front Seat Wire RH
    *a
    Front view of wire harness connector
    (to Occupant Detection ECU)



NG
Go to step 11
OK


3.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)


    C238380E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for TMMK Made: 
    Tester Connection
    Condition
    Specified Condition
    d8-1 (SVC3) - Body ground
    Always
    1 MΩ or higher
    d8-2 (SVC4) - Body ground
    Always
    1 MΩ or higher
    for SIA Made: 
    Tester Connection
    Condition
    Specified Condition
    d18-1 (SVC3) - Body ground
    Always
    1 MΩ or higher
    d18-2 (SVC4) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *A
    for TMMK Made
    *B
    for SIA Made
    *1
    Rear Occupant Classification Sensor LH
    *2
    Rear Occupant Classification Sensor RH
    *3
    Occupant Detection ECU
    *4
    Front Seat Wire RH
    *a
    Front view of wire harness connector
    (to Occupant Detection ECU)



NG
REPLACE FRONT SEAT WIRE RH
OK


4.CHECK FRONT SEAT WIRE RH (SHORT)


    C238380E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for TMMK Made: 
    Tester Connection
    Condition
    Specified Condition
    d8-1 (SVC3) - d8-2 (SVC4)
    Always
    1 MΩ or higher
    for SIA Made: 
    Tester Connection
    Condition
    Specified Condition
    d18-1 (SVC3) - d18-2 (SVC4)
    Always
    1 MΩ or higher

    Text in Illustration 
    *A
    for TMMK Made
    *B
    for SIA Made
    *1
    Rear Occupant Classification Sensor LH
    *2
    Rear Occupant Classification Sensor RH
    *3
    Occupant Detection ECU
    *4
    Front Seat Wire RH
    *a
    Front view of wire harness connector
    (to Occupant Detection ECU)



NG
REPLACE FRONT SEAT WIRE RH
OK


5.CHECK DTC
  1. Connect the connectors to the occupant detection ECU and 2 rear occupant classification sensors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in the occupant detection ECU (Click here).

  1. Clear the DTCs stored in the airbag sensor assembly (Click here for Separate Type Yaw Rate Sensor, Click here for Built-in Type Yaw Rate Sensor).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Check for DTCs (Click here).

    OK:
    DTC B1793 is not output.

    HINT:
    Codes other than DTC B1793 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.CHECK OCCUPANT DETECTION ECU
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Replace the occupant detection ECU with a known good one (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in the occupant detection ECU (Click here).

  1. Clear the DTCs stored in the airbag sensor assembly (Click here for Separate Type Yaw Rate Sensor, Click here for Built-in Type Yaw Rate Sensor).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Check for DTCs (Click here).

    OK:
    DTC B1793 is not output.

    HINT:
    Codes other than DTC B1793 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Restore the occupant detection ECU that was installed for testing to its original location (Click here).



NG
Go to step 9
OK


7.REPLACE OCCUPANT DETECTION ECU
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Replace the occupant detection ECU with a new one (Click here).

  1. Connect the cable to the negative (-) battery terminal.


NEXT


8.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).


NEXT

END 

9.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Replace the front seat frame with adjuster assembly RH (Click here for TMMK Made Manual Seat, Click here for TMMK Made Power Seat, Click here for SIA Made Manual Seat, Click here for SIA Made Power Seat).

  1. Connect the cable to the negative (-) battery terminal.


NEXT


10.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).


NEXT

END 

11.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Replace the front seat frame with adjuster assembly RH (Click here for TMMK Made Manual Seat, Click here for TMMK Made Power Seat, Click here for SIA Made Manual Seat, Click here for SIA Made Power Seat).

    NOTICE:
    Replace the front seat wire RH at the same time.

    HINT:
    When the front seat wire RH has a short to B+, the rear occupant classification sensors will be damaged. Therefore, replace the front seat wire RH and the front seat frame with adjuster assembly RH, which includes the rear occupant classification sensors.

  1. Connect the cable to the negative (-) battery terminal.


NEXT


12.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).


NEXT

END