RADIO RECEIVER > INSTALLATION |
| 1. PRECAUTION (for Radio and Display Type with Intuitive Parking Assist System) |
| 2. INSTALL RADIO RECEIVER ASSEMBLY (for Radio Receiver Type) |
| 3. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type) |
| 4. INSTALL NAVIGATION ECU SUB-ASSEMBLY (for Radio and Display Type with Intuitive Parking Assist System) |
| 5. INSTALL HARD DISK DRIVE (for Radio and Display Type with Intuitive Parking Assist System) |
![]() |
Insert the hard disk drive in the direction shown by the arrow in the illustration to install it.
Engage the 2 guides to temporarily install the cover.
Install the cover with the 2 screws.
| 6. INSTALL EXTENSION MODULE (for Radio and Display Type) |
| 7. INSTALL AIR CONDITIONING CONTROL ASSEMBLY |
![]() |
Engage the guide and 4 clips to install the air conditioning control assembly as shown in the illustration.
| 8. INSTALL NO. 1 RADIO BRACKET (for Radio Receiver Type) |
Install the No. 1 radio bracket with the 5 screws.
| 9. INSTALL NO. 2 RADIO BRACKET (for Radio Receiver Type) |
Install the No. 2 radio bracket with the 5 screws.
| 10. INSTALL NO. 1 RADIO BRACKET (for Radio and Display Type) |
w/o Navigation System:
Install the No. 1 radio bracket with the 5 screws.
w/ Navigation System:
Install the No. 1 radio bracket with the 7 screws.
| 11. INSTALL NO. 2 RADIO BRACKET (for Radio and Display Type) |
w/o Navigation System:
Install the No. 2 radio bracket with the 5 screws.
w/ Navigation System:
Install the No. 2 radio bracket with the 7 screws.
| 12. INSTALL NO. 1 RADIO RECEIVER BRACKET (for Radio and Display Type with Intuitive Parking Assist System) |
Install the No. 1 radio receiver bracket with the 5 screws.
| 13. INSTALL NO. 2 RADIO RECEIVER BRACKET (for Radio and Display Type with Intuitive Parking Assist System) |
Install the No. 2 radio receiver bracket with the 5 screws.
| 14. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio Receiver Type) |
Connect each connector.
Engage the 8 clips to the vehicle body to temporarily install the radio receiver assembly with air conditioning control assembly.
Install the radio receiver assembly with air conditioning control assembly with the 4 bolts.
| 15. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type) |
Connect each connector.
Engage the 8 clips to the vehicle body to temporarily install the radio receiver assembly with air conditioning control assembly.
Install the radio receiver assembly with air conditioning control assembly with the 4 bolts.
| 16. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 6 clips to install the No. 2 instrument panel register assembly.
| 17. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
Connect the connector.
Engage the clamp.
![]() |
Engage the 6 clips and 7 claws to install the center instrument cluster finish panel assembly.
| 18. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
Connect each connector.
Engage the 4 clips and guide.
Install the upper console panel sub-assembly with the 2 screws <C> or <D>.
| 19. INSTALL BOX BOTTOM MAT |
Install the box bottom mat.
| 20. INSTALL REAR CONSOLE BOX ASSEMBLY |
| 21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Radio and Display Type with Intuitive Parking Assist System) |
| 22. INSPECT HARD DISK DRIVE (for Radio and Display Type with Intuitive Parking Assist System) |
| 23. REPLACED OPERATION (w/ Parking Assist Monitor System) |