Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > REMOVAL

for Preparation Click here


HINT:
  1. The following procedure is for the No. 1 parking brake cable assembly and No. 3 parking brake cable assembly.
  2. Use the same procedure for the No. 3 parking brake cable assembly and No. 2 parking brake cable assembly.



1. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY
(Click here)


2. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY


    C239385
  1. Pull up the parking brake pedal claw.

    NOTICE:
    Do not damage the No. 1 parking brake cable assembly.



    C239384
  1. Remove the adjusting nut.



    C239386
  1. Remove the clip from the No. 1 parking brake cable assembly.

  1. Remove the No. 1 parking brake cable assembly from the parking brake pedal assembly.



3. REMOVE REAR DOOR SCUFF PLATE LH


    B278979
  1. Disengage the 6 claws and remove the rear door scuff plate LH.

    HINT:
    Disengage the claws from the rear side of the scuff plate.



4. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the rear door opening trim weatherstrip LH.



5. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    B271081
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



6. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B271082
  1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.



7. REMOVE CENTER PILLAR LOWER GARNISH LH


    B278989
  1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.



8. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



10. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



12. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side.



13. REMOVE FRONT SEAT ASSEMBLY LH
  1. for TMMK Made Manual Seat: (Click here)
  2. for TMMK Made Power Seat: (Click here)
  3. for SIA Made Manual Seat: (Click here)
  4. for SIA Made Power Seat: (Click here)


14. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



15. REMOVE AUDIO AMPLIFIER COVER (for 10 Speakers)


    E223732
  1. Using a clip remover, remove the 2 clips and audio amplifier cover.



16. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)


    E223733
  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect each connector.

  1. Disengage the clamp.



    E223734
  1. Remove the bolt.

  1. Disengage the 2 guides and remove the stereo component amplifier assembly with bracket.



17. REMOVE AUDIO AMPLIFIER COVER (w/ Manual (SOS) Switch)


    E223742
  1. Using a clip remover, remove the 2 clips and audio amplifier cover.



18. REMOVE DCM (TELEMATICS TRANSCEIVER) WITH BACK-UP BATTERY (w/ Manual (SOS) Switch)


    E223743
  1. Disconnect each connector.

  1. Disengage the 3 clamps.



    E223744
  1. Remove the bolt.

  1. Disengage the 2 guides and remove the DCM (telematics transceiver) with back-up battery.



19. REMOVE FLOOR CARPET HOOK


    E227413E01
  1. Disengage the 6 guides.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



    E227415E01
  1. Disengage the 6 claws and remove the 6 floor carpet hooks.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



20. REMOVE NO. 4 CROSS MEMBER FLOOR REINFORCEMENT SUB-ASSEMBLY


    E227149
  1. Remove the screw.



    E227150
  1. Disengage the guide to disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

  1. Turn back the floor carpet to a position where the No. 4 cross member floor reinforcement sub-assembly can be removed.



    C239387
  1. Remove the 8 bolts and No. 4 cross member floor reinforcement sub-assembly.



21. REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY


    C239388E01
  1. Separate the No. 3 parking brake cable assembly from the parking brake equalizer.
    Text in Illustration 
    *1
    Parking Brake Equalizer
    *2
    No. 2 Parking Brake Cable Assembly
    *3
    No. 3 Parking Brake Cable Assembly
    *4
    No. 4 Parking Brake Cable Assembly

  1. Separate the No. 2 parking brake cable assembly to remove the parking brake equalizer.



    C239389E01
  1. Slide the parking brake equalizer and rubber boot.
    Text in Illustration 
    *1
    Rubber Boot
    *2
    Parking Brake Equalizer
    *3
    No. 4 Parking Brake Cable Assembly

  1. Remove the No. 4 parking brake cable assembly from the parking brake equalizer.



22. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2AR-FE)
(Click here)


23. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for 2AR-FE)


    C239390
  1. Remove the 3 nuts and front No. 2 floor heat insulator.



24. REMOVE PARKING BRAKE SHOE LEVER
(Click here)


25. REMOVE NO. 2 FLOOR UNDER COVER (for LH Side)


  1. w/ Floor Under Cover:



      C239063
    1. Remove the 2 bolts and 2 clips.
      Text in Illustration 
      V100135
      Bolt
      V100136
      Nut (attached to under cover)

    2. Disengage the 3 nuts and remove the No. 2 floor under cover.



26. REMOVE NO. 1 FLOOR UNDER COVER (for RH Side)


    C239064
  1. Remove the 2 bolts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut (attached to under cover)

  1. Disengage the 3 nuts and 2 clips, and remove the No. 1 floor under cover.



27. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C239391
  1. Remove the clip from the No. 3 parking brake cable assembly.



    C239392
  1. Remove the bolt and separate the No. 3 parking brake cable assembly.



  1. Remove the 4 bolts, nut and No. 3 parking brake cable assembly.


    C239393



28. REMOVE NO. 2 PARKING BRAKE CABLE CLAMP
  1. Remove the No. 2 parking brake cable clamp.