SFI SYSTEM > Starter Signal Circuit |

| 1.CHECK WHETHER ENGINE CAN BE CRANKED |
Check if the engine can be cranked.
| Result | Proceed to |
| Engine cannot be cranked | A |
| Engine can be cranked | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Starter Signal.
Check the value displayed on the Techstream when the engine switch is turned to the on (IG) and the engine is started.
| Switch Condition | Tester Display (Starter Signal) |
| Engine switch on (IG) | Close (Off) |
| Engine started | Open (On) |
|
| ||||
| OK | |
| 3.INSPECT RELAY (ST RELAY) |
Inspect the ST relay (Click here).
|
| ||||
| OK | |
| 4.INSPECT STARTER ASSEMBLY |
Inspect the starter assembly (Click here).
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY) |
Remove the ST relay from the engine room relay block and junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (ST relay) - E9-1 | Always | Below 1 Ω |
| 3 (ST relay) or E9-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY) |
Disconnect the starter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F2-1 - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND) |
Remove the ST relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (ST relay) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY) |
Remove the ST relay from the engine room relay block and junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E4-9 - 2 (ST relay) | Always | Below 1 Ω |
| A43-7 (STA) - 2 (ST relay) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (BATTERY - ST RELAY) |
Remove the ST relay from the engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 5 (ST relay) - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | ||
| ||
| 10.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Starter Signal.
Check the value displayed on the Techstream when the engine switch is turned to the on (IG) and the engine is started.
| Switch Condition | Tester Display (Starter Signal) |
| Engine switch on (IG) | Close (OFF) |
| Engine started | Open (ON) |
|
| ||||
| OK | ||
| ||
| 11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch assembly (Click here).
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM) |
Disconnect the park/neutral position switch assembly connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A43-7 (STA) - E4-4 | Always | Below 1 Ω |
| A43-7 (STA) - E26-65 (NSW) | Always | Below 1 Ω |
| A43-7 (STA) or E4-4 or E26-65 (NSW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY - CERTIFICATION ECU) |
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Remove the ST relay from the engine room relay block and junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E4-9 - A25-9 (STA) | Always | Below 1 Ω |
| E4-9 or A25-9 (STA) or 2 (ST relay) or A43-7 (STA) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||