Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  P0156  Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  P0158  Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A203088E13
2.729,1.427 3.333,1.219 false 2.927,1.313 3.25,1.021 false 2.74,1.635 3.281,1.635 false 2.604,2.24 3.281,2.208 false 2.698,2.427 3.271,2.563 false 1.198,2.865 1.427,2.865 false 1.521,0.823 2.531,1.021 1.01,0.198 10 false Atmospheric Air 3.302,0.917 4.042,1.115 0.74,0.198 10 false Housing 3.375,1.146 4.906,1.344 1.531,0.198 10 false Platinum Electrode 4.063,0.844 5.031,1.042 0.969,0.198 10 false Output Voltage 4.906,0.531 6.292,0.729 1.385,0.198 10 false Ideal Air Fuel Mixture 2.021,3.115 2.917,3.313 0.896,0.198 10 false Exhaust Gas 3.344,1.563 4.49,1.958 1.146,0.396 10 false Solid Electrolyte (Zirconia Element) 3.313,2.49 4.51,2.688 1.198,0.198 10 false Coating (Ceramic) 3.333,2.115 3.813,2.313 0.479,0.198 10 false Heater 1.469,2.792 1.906,3 0.438,0.208 10 false Cover 4.625,2.875 6.604,3.073 1.979,0.198 10 false Richer - Air Fuel Ratio - Leaner

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) Abnormal voltage output:

During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

Heated oxygen sensor voltage does not decrease to less than 0.21 V

2.

Heated oxygen sensor voltage does not increase to 0.59 V or higher



·

Heated oxygen sensor (bank 1 sensor 2) circuit

·

Heated oxygen sensor (bank 1 sensor 2)

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

PCV valve and hose

·

Intake system


Comes on (Euro-OBD) / - (except Euro-OBD) DTC stored (Euro-OBD) / - (except Euro-OBD)
P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) Low voltage (open):

During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

Heated oxygen sensor voltage output less than 0.21 V

2.

Target air fuel ratio rich



·

Heated oxygen sensor (bank 1 sensor 2) circuit

·

Heated oxygen sensor (bank 1 sensor 2)

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Gas leak from exhaust system


Comes on DTC stored
P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) High voltage (short):

During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

Heated oxygen sensor voltage output higher than 0.59 V

2.

Target air fuel ratio lean



·

Heated oxygen sensor (bank 1 sensor 2) circuit

·

Heated oxygen sensor (bank 1 sensor 2)

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on (Euro-OBD) / - (except Euro-OBD) DTC stored (Euro-OBD) / - (except Euro-OBD)
P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) Abnormal voltage output:

During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

Heated oxygen sensor voltage does not decrease to less than 0.21 V

2.

Heated oxygen sensor voltage does not increase to 0.59 V or higher



·

Heated oxygen sensor (bank 2 sensor 2) circuit

·

Heated oxygen sensor (bank 2 sensor 2)

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

PCV valve and hose

·

Intake system


Comes on (Euro-OBD) / - (except Euro-OBD) DTC stored (Euro-OBD) / - (except Euro-OBD)
P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) Low voltage (open):

During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

Heated oxygen sensor voltage output less than 0.21 V

2.

Target air fuel ratio rich



·

Heated oxygen sensor (bank 2 sensor 2) circuit

·

Heated oxygen sensor (bank 2 sensor 2)

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Gas leak from exhaust system


Comes on DTC stored
P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) High voltage (short):

During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

Heated oxygen sensor voltage output higher than 0.59 V

2.

Target air fuel ratio lean



·

Heated oxygen sensor (bank 2 sensor 2) circuit

·

Heated oxygen sensor (bank 2 sensor 2)

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on (Euro-OBD) / - (except Euro-OBD) DTC stored (Euro-OBD) / - (except Euro-OBD)

MONITOR DESCRIPTION

Active Air Fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of Heated Oxygen Sensor (DTCs P0136 and P0156)


While the ECM is performing active air fuel ratio control, the air fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the heated oxygen sensor voltage does not decrease to less than 0.21 V and does not increase to 0.59 V or higher during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136 or P0156.

A152942E33
2.969,2.125 3.156,1.625 false 3.156,1.625 3.292,1.625 false 2.792,2.344 2.917,2.604 false 2.917,2.604 3.115,2.604 false 0.073,0.052 5.271,0.333 5.198,0.281 10 false Heated Oxygen Sensor Circuit Malfunction (P0136 and P0156: Abnormal Voltage) 4.74,1.292 5.438,1.49 0.698,0.198 10 false Operation 4.531,0.802 5.677,1.042 1.146,0.24 10 false 15 to 20 seconds 3.333,1.552 3.854,1.74 0.521,0.188 10 false Normal 2.177,1.354 2.521,1.531 0.344,0.177 10 false OFF 2.083,2.135 2.542,2.302 0.458,0.167 10 false 0.59 V 2.083,2.896 2.542,3.073 0.458,0.177 10 false 0.21 V 3.177,2.521 3.865,2.708 0.688,0.188 10 false Abnormal 0.083,1.333 1.958,1.552 1.875,0.219 10 false Active air fuel ratio control 0.083,2.531 2.052,2.771 1.969,0.24 10 false Heated oxygen sensor voltage


Open or Short in Heated Oxygen Sensor Circuit (DTCs P0137 and P0157 or P0138 and P0158)


During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short circuit, or the voltage output of the sensor noticeably decreases, the OSC indicated an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor voltage output is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157. When the target air fuel ratio is lean and the voltage output is higher than 0.59 V (rich) during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormally high and stores DTC P0138 or P0158.

*: The TWC has the capability to store oxygen. The OSC and the emissions purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated, based on the calculated OSC value (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0420).

A152992E27
5.792,3.792 6.021,4.031 false 4.281,2.063 4.448,1.729 false 4.448,1.729 4.594,1.729 false 5.323,2.406 5.448,1.719 false 5.448,1.719 5.625,1.719 false 5.688,3.031 5.844,2.563 false 5.844,2.563 6,2.563 false 5.75,6.583 5.969,6.104 false 5.969,6.104 6.104,6.104 false 0.063,0.052 4.5,0.333 4.438,0.281 10 false Heated Oxygen Sensor Circuit Low Voltage (P0137 and P0157: Open) 0.281,1.219 1.229,1.563 0.948,0.344 10 false Active Air Fuel Ratio Control 0.292,3.208 1.354,3.573 1.063,0.365 10 false Heated Oxygen Sensor Voltage 0.281,2.083 1.635,2.281 1.354,0.198 10 false Target Air Fuel Ratio 2.156,2.052 3.073,2.49 0.917,0.438 10 false Stoichiometric Air Fuel Level 2.823,1.375 3.188,1.573 0.365,0.198 10 false Off 2.625,3.5 3.073,3.698 0.448,0.198 10 false 0.21 V 0.063,4.208 4.51,4.469 4.448,0.26 10 false Heated Oxygen Sensor Circuit High Voltage (P0138 and P0158: Short) 0.281,4.854 1.313,5.229 1.031,0.375 10 false Active Air Fuel Ratio Control 0.281,6.906 1.385,7.271 1.104,0.365 10 false Heated Oxygen Sensor Voltage 0.281,5.74 1.76,5.938 1.479,0.198 10 false Target Air Fuel Ratio 2.094,5.667 3.01,6.104 0.917,0.438 10 false Stoichiometric Air Fuel Level 2.76,4.979 3.115,5.177 0.354,0.198 10 false Off 4.313,0.792 5.469,0.99 1.156,0.198 10 false 15 to 20 seconds 4.521,1.313 5.281,1.51 0.76,0.198 10 false Operation 4.5,4.927 5.198,5.125 0.698,0.198 10 false Operation 4.667,5.74 5.063,5.938 0.396,0.198 10 false Lean 4.646,1.646 5.208,1.844 0.563,0.198 10 false Normal 6.156,6.021 6.844,6.219 0.688,0.198 10 false Abnormal 5.677,1.635 6.323,1.833 0.646,0.198 10 false Abnormal 6.063,4.052 6.802,4.25 0.74,0.198 10 false Abnormal 6.052,2.479 6.615,2.677 0.563,0.198 10 false Normal 4.719,2.469 5.083,2.667 0.365,0.198 10 false Rich 2.5,6.688 2.99,6.885 0.49,0.198 10 false 0.59 V


MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor (sensor 2)
Required Sensors/Components (Related) Crankshaft position sensor
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Throttle position sensor
Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

P0136, P0137, P0138, P0156, P0157 and P0158: Heated Oxygen Sensor Voltage Check (Voltage Malfunction, High Voltage and Low Voltage)
Active air fuel ratio control Executing
Active air fuel ratio control begins when all of the following conditions are met -
Battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idling Off
Engine speed Less than 3200 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 70%

TYPICAL MALFUNCTION THRESHOLDS

P0136 and P0156: Heated Oxygen Sensor Voltage Check (Voltage Malfunction)
Either of the following conditions is met 1 or 2
1. Both of the following conditions are met -
Commanded air fuel ratio 14.3 or less
Heated oxygen sensor voltage 0.21 V or higher, and less than 0.59 V
2. Both of the following conditions are met -
Commanded air fuel ratio 14.9 or more
Heated oxygen sensor voltage 0.21 V or higher, and less than 0.59 V

P0137 and P0157: Heated Oxygen Sensor Voltage Check (Low Voltage)
Both of the following conditions are met -
Commanded air fuel ratio 14.3 or less
Heated oxygen sensor voltage Less than 0.21 V

P0138 and P0158: Heated Oxygen Sensor Voltage Check (High Voltage)
Both of the following conditions are met -
Commanded air fuel ratio 14.9 or more
Heated oxygen sensor voltage Higher than 0.59 V

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A200170E22
2.698,2.354 2.927,2.573 0.229,0.219 10 false [B] 4.115,0.729 4.375,1.01 0.26,0.281 10 false [C] 5.073,3.104 5.313,3.333 0.24,0.229 10 false [D] 1.052,0.5 1.688,0.688 0.635,0.188 10 false 100 km/h 1.125,1.365 2.396,1.552 1.271,0.188 10 false 60 km/h 1.292,2.177 1.688,2.531 0.396,0.354 10 false Idling 0.531,2.479 1.75,2.656 1.219,0.177 10 false Ignition Switch ON 2.427,3.135 3.281,3.375 0.854,0.24 10 false Warming up 3.604,3.146 4.906,3.385 1.302,0.24 10 false 10 minutes or more 2.073,2.552 2.313,2.792 0.24,0.24 10 false [A]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

With the shift lever in D, drive the vehicle at 60 to 100 km/h (37 to 62 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.




WIRING DIAGRAM

A266381E02
5.719,0.646 6.094,0.813 0.375,0.167 10 false HT1B 5.708,1.448 6.104,1.656 0.396,0.208 10 false OX1B 0.573,1.885 1.198,2.229 0.625,0.344 10 false EFI-MAIN NO. 1 5.375,0.667 5.646,0.823 0.271,0.156 10 false E26 5.365,1.438 5.656,1.656 0.292,0.219 10 false E26 5.365,2.75 5.635,2.906 0.271,0.156 10 false E26 5.375,3.292 5.667,3.5 0.292,0.208 10 false E26 5.375,4.073 5.646,4.229 0.271,0.156 10 false E26 5.375,5.365 5.646,5.521 0.271,0.156 10 false E26 4.708,0.563 4.813,0.708 0.104,0.146 10 false 1 4.708,1.344 4.813,1.49 0.104,0.146 10 false 3 5.417,0.49 5.594,0.635 0.177,0.146 10 false 28 4.146,3.198 4.573,3.365 0.427,0.167 10 false HT2B 4.115,3.896 4.51,4.063 0.396,0.167 10 false OX2B 4.281,0.563 4.708,0.729 0.427,0.167 10 false HT1B 4.271,1.25 4.667,1.417 0.396,0.167 10 false OX1B 3.708,3.198 3.906,3.365 0.198,0.167 10 false +B 3.719,3.969 3.917,4.135 0.198,0.167 10 false E2 4.552,3.188 4.656,3.333 0.104,0.146 10 false 1 4.552,3.969 4.656,4.115 0.104,0.146 10 false 3 3.542,3.188 3.646,3.333 0.104,0.146 10 false 2 3.542,3.979 3.646,4.125 0.104,0.146 10 false 4 5.375,1.26 5.625,1.406 0.25,0.146 10 false 101 5.698,5.354 6.094,5.521 0.396,0.167 10 false EX2B 5.708,4.073 6.135,4.24 0.427,0.167 10 false OX2B 5.406,3.115 5.594,3.26 0.188,0.146 10 false 22 5.385,3.896 5.646,4.042 0.26,0.146 10 false 133 5.365,2.573 5.625,2.719 0.26,0.146 10 false 102 4.885,3.635 5,3.781 0.115,0.146 10 false * 4.979,1 5.156,1.146 0.177,0.146 10 false * 6.052,6.406 6.438,6.646 0.385,0.24 10 false ECM 5.375,5.854 5.656,6.042 0.281,0.188 10 false A25 5.417,5.677 5.594,5.823 0.177,0.146 10 false 46 5.708,5.854 6.146,6.021 0.438,0.167 10 false MREL 5.375,5.177 5.635,5.323 0.26,0.146 10 false 134 3.573,1.958 5.031,2.365 1.458,0.406 10 false Heated Oxygen Sensor (Bank 1 Sensor 2) 0.719,5.333 1.208,5.604 0.49,0.271 10 false Battery 0.573,3.479 1.146,3.688 0.573,0.208 10 false FL MAIN 3.188,6.083 4,6.292 0.813,0.208 10 false *: Shielded 1.521,1.375 2.177,1.594 0.656,0.219 10 false EFI MAIN 1.385,1.719 2.854,2.052 1.469,0.333 10 false No. 1 Integration Relay 5.719,3.292 6.146,3.458 0.427,0.167 10 false HT2B 5.708,2.76 6.104,2.927 0.396,0.167 10 false EX1B 3.677,0.563 3.781,0.74 0.104,0.177 10 false 2 3.688,1.344 3.792,1.49 0.104,0.146 10 false 4 3.854,0.563 4.073,0.729 0.219,0.167 10 false +B 3.865,1.333 4.063,1.5 0.198,0.167 10 false E2 3.573,1.792 3.885,1.958 0.313,0.167 10 false E22 3.281,4.521 4.75,4.958 1.469,0.438 10 false Heated Oxygen Sensor (Bank 2 Sensor 2) 3.281,4.365 3.594,4.531 0.313,0.167 10 false E20 1.042,0.469 1.177,0.656 0.135,0.188 10 false 1 1,0.667 1.219,0.906 0.219,0.24 10 false 1B 2.99,0.469 3.083,0.635 0.094,0.167 10 false 8 2.927,0.667 3.115,0.833 0.188,0.167 10 false 1A 2.24,0.802 2.875,0.969 0.635,0.167 10 false EFI NO. 3 1.313,1.313 1.438,1.49 0.125,0.177 10 false 2 1.177,1.51 1.375,1.677 0.198,0.167 10 false 1E 3.021,1.313 3.115,1.479 0.094,0.167 10 false 7 2.885,1.51 3.083,1.677 0.198,0.167 10 false 1C

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the tester on.

4.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

6.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
O2S B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E17
5.792,3.781 7.115,4.052 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.49,1.594 1.958,1.781 0.469,0.188 8 false 12.5% 1.448,1.833 1.896,2.021 0.448,0.188 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 4.125,1.594 4.573,1.781 0.448,0.188 8 false 12.5% 4.083,1.823 4.531,2.01 0.448,0.188 8 false -12.5% 4.115,3.698 4.563,3.885 0.448,0.188 8 false 12.5% 4.073,3.896 4.521,4.083 0.448,0.188 8 false -12.5% 4.073,5.948 4.521,6.135 0.448,0.188 8 false -12.5% 4.052,8.01 4.5,8.198 0.448,0.188 8 false -12.5% 4.115,5.74 4.563,5.927 0.448,0.188 8 false 12.5% 4.094,7.781 4.542,7.969 0.448,0.188 8 false 12.5% 1.469,7.813 1.917,8 0.448,0.188 8 false 12.5% 1.479,5.75 1.927,5.938 0.448,0.188 8 false 12.5% 1.5,3.677 1.948,3.865 0.448,0.188 8 false 12.5% 1.448,3.896 1.896,4.083 0.448,0.188 8 false -12.5% 1.438,5.948 1.885,6.135 0.448,0.188 8 false -12.5% 1.427,8.021 1.875,8.208 0.448,0.188 8 false -12.5% 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.125,0.688 0.573,0.938 0.448,0.25 10 false Case 0.958,0.583 2.823,1 1.865,0.417 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.5,0.583 5.49,0.99 1.99,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.969,0.583 7.01,1 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4.031 7.125,4.469 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.448 7.125,4.885 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.917,5.792 6.969,6.167 1.052,0.375 10 false - Heated oxygen sensor 5.927,6.198 6.969,6.625 1.042,0.427 10 false - Heated oxygen sensor heater 5.927,6.615 6.969,7.052 1.042,0.438 10 false - Heated oxygen sensor circuit 5.927,7.698 6.813,8.104 0.885,0.406 10 false - Fuel injector assembly 5.917,8.115 7.073,8.448 1.156,0.333 10 false - Fuel pressure 5.917,8.365 6.969,9.375 1.052,1.01 10 false - Gas leak from exhaust system (Air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG

·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2; then press the view button.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
P0138 or P0158 is output A
P0137 or P0157 is output B
P0136 or P0156 is output C
P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output D


HINT:

If any DTCs other than P0136, P0137, P0138, P0156, P0157 and P0158 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

12.CHECK FOR EXHAUST GAS LEAK

C

10.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / O2S B1S2 or O2S B2S2.

Powertrain > Engine > Data List
Tester Display
O2S B1S2
O2S B2S2
50003 234 44,48

e.

Allow the engine to idle.


f.

Read the heated oxygen sensor output voltage while idling.


Result:
Heated Oxygen Sensor Output Voltage Proceed to
1.0 V or higher A
Less than 1.0 V B



A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.

Disconnect the heated oxygen sensor connector.

A258655C04
1.573,0.573 1.885,0.885 false 1.573,1.458 1.917,1.26 false 2.521,1.458 2.208,1.26 false 4.76,0.49 5.073,0.802 false 4.76,1.469 5.073,1.292 false 5.833,1.469 5.51,1.271 false 1.385,0.427 1.594,0.594 0.208,0.167 10 false +B 1.385,1.458 1.594,1.625 0.208,0.167 10 false E2 2.521,1.458 2.917,1.625 0.396,0.167 10 false OX1B 0.365,0.094 0.573,0.26 0.208,0.167 10 false *a 1.99,0.146 2.135,0.313 0.146,0.167 10 false *1 4.573,0.344 4.781,0.51 0.208,0.167 10 false +B 4.573,1.469 4.781,1.635 0.208,0.167 10 false E2 5.833,1.469 6.229,1.635 0.396,0.167 10 false OX2B 5.167,0.146 5.313,0.313 0.146,0.167 10 false *2
*1 Bank 1 *2 Bank 2
*a Component without harness connected
(Heated Oxygen Sensor)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+B) - 4 (E2) Always 10 kΩ or higher
2 (+B) - 3 (OX1B) Always 10 kΩ or higher
2 (+B) - 4 (E2) Always 10 kΩ or higher
2 (+B) - 3 (OX2B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Turn the ignition switch off and wait for 5 minutes or more.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-28 (HT1B) - E26-101 (OX1B) Always 10 kΩ or higher
E26-22 (HT2B) - E26-133 (OX2B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
AFS Voltage B2S1
O2S B1S2
O2S B2S2
50004 234 2 35,37,44,48

f.

Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2, on the tester.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.




Result:
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
Alternates between higher and less than 3.3 V OK
Remains higher than 3.3 V NG
Remains less than 3.3 V


HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1 or AFS Voltage B2S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E61
5.885,2.479 6.365,1.396 false 5.552,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.438,2.042 4.313,2.042 4.313,2.042 4.104,1.688 false 3.573,2.625 3.188,2.938 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.667,0.26 3.188,0.458 0.521,0.198 10 false 12.5% 4.125,1.125 4.781,1.323 0.656,0.198 10 false -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 4,1.344 0.927,0.198 10 false Malfunction 5.854,2.615 6.792,2.792 0.938,0.177 10 false Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.938,1.813 0.531,0.688 10 false Air Fuel Ratio Sensor Output 4.49,1.969 4.979,2.135 0.49,0.167 10 false Normal


OK

6.INSPECT AIR FUEL RATIO SENSOR

NG

7.REPLACE AIR FUEL RATIO SENSOR
6.INSPECT AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate less than 2.2 mA in this test.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


f.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


g.

Stop the vehicle.


h.

Enter the following menus: Powertrain / Engine / Data List / All Data / AFS Current B1S1 and AFS Current B2S1.

Powertrain > Engine > Data List
Tester Display
AFS Current B1S1
AFS Current B2S1
50003 234 39,41

i.

Drive the vehicle at 60 km/h (37 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


A152792E61
1.357,2.513 2.638,2.697 1.281,0.184 10 10 minutes or more 2.973,2.513 4.186,2.697 1.213,0.184 10 5 seconds or more 4.271,2.513 5.468,2.697 1.197,0.184 10 5 seconds or more 5.56,2.513 6.739,2.697 1.179,0.184 10 5 seconds or more 0.152,0.078 1.452,0.293 1.3,0.215 12 Driving Pattern: 0.455,1.379 1.114,1.595 0.659,0.216 10 60 km/h 0.527,2.139 1.063,2.342 0.536,0.203 10 0 km/h

j.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard current:

Less than 2.2 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the tester.




Result:
Proceed to
OK
NG



OK

15.REPLACE HEATED OXYGEN SENSOR

NG

7.REPLACE AIR FUEL RATIO SENSOR
7.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

8.PERFORM CONFIRMATION DRIVING PATTERN
8.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0138, P0156 OR P0158)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0138, P0156 OR P0158)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

e.

Input the DTC: P0136, P0138, P0156 or P0158.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.


Result:
Result Proceed to
ABNORMAL
(DTC P0136, P0138, P0156 or P0158 is output)
A
NORMAL
(DTC is not output)
B



A

B

END

10.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2S B1S2 or O2S B2S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
O2S B1S2
O2S B2S2
50004 234 2 44,48

f.

Change the fuel injection volume using the tester, monitor the voltage output of the heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard Voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.



Result:
Proceed to
OK
NG



OK

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

12.CHECK FOR EXHAUST GAS LEAK
11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
AFS Voltage B2S1
O2S B1S2
O2S B2S2
50004 234 2 35,37,44,48

f.

Change the fuel injection volume using the tester, and monitor the voltage output of air fuel ratio and heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2, on the tester.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
Tester Display
(Sensor)
Voltage Variation Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
Alternates between higher and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V


HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1 or AFS Voltage B2S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E61
5.885,2.479 6.365,1.396 false 5.552,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.438,2.042 4.313,2.042 4.313,2.042 4.104,1.688 false 3.573,2.625 3.188,2.938 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.667,0.26 3.188,0.458 0.521,0.198 10 false 12.5% 4.125,1.125 4.781,1.323 0.656,0.198 10 false -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 4,1.344 0.927,0.198 10 false Malfunction 5.854,2.615 6.792,2.792 0.938,0.177 10 false Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.938,1.813 0.531,0.688 10 false Air Fuel Ratio Sensor Output 4.49,1.969 4.979,2.135 0.49,0.167 10 false Normal



OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

7.REPLACE AIR FUEL RATIO SENSOR
12.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

13.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

13.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

14.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-1 (HT1B) - E26-28 (HT1B) Always Below 1 Ω
E22-3 (OX1B) - E26-101 (OX1B) Always Below 1 Ω
E22-4 (E2) - E26-102 (EX1B) Always Below 1 Ω
E20-1 (HT2B) - E26-22 (HT2B) Always Below 1 Ω
E20-3 (OX2B) - E26-133 (OX2B) Always Below 1 Ω
E20-4 (E2) - E26-134 (EX2B) Always Below 1 Ω
E22-1 (HT1B) or E26-28 (HT1B) - Body ground Always 10 kΩ or higher
E22-3 (OX1B) or E26-101 (OX1B) - Body ground Always 10 kΩ or higher
E20-1 (HT2B) or E26-22 (HT2B) - Body ground Always 10 kΩ or higher
E20-3 (OX2B) or E26-133 (OX2B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE HEATED OXYGEN SENSOR
a.

Result:
Proceed to
NEXT



NEXT

16.PERFORM CONFIRMATION DRIVING PATTERN
16.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

e.

Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result:
Result Proceed to
ABNORMAL
(DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output)
A
NORMAL
(DTC is not output)
B


HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

B

END