Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2012.02–2015.04
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0051  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)  P0052  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  P103D  A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2195).

HINT:
·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A255442E07
0.073,0.063 3.167,0.229 3.094,0.167 10 false Reference (System Diagram of Bank 1 Sensor 1): 1.281,0.979 1.677,1.208 0.396,0.229 10 false A/F 0.292,0.844 0.781,1.281 0.49,0.438 10 false from Battery 2,1.792 2.833,2.125 0.833,0.333 10 false A/F HTR 0.198,2.125 0.802,2.906 0.604,0.781 10 false from EFI MAIN Relay 3.49,0.76 4,1.083 0.51,0.323 10 false +B 3.865,1.01 4.302,1.156 0.438,0.146 10 false Heater 3.854,1.688 4.313,1.833 0.458,0.146 10 false Sensor 3.354,1.438 4.021,1.719 0.667,0.281 10 false A1A- 4.479,1.438 5.021,1.729 0.542,0.292 10 false A1A+ 4.479,0.76 4.99,1.073 0.51,0.313 10 false HA1A 5.198,1.438 5.708,1.833 0.51,0.396 10 false A1A+ 5.198,2.344 5.708,2.667 0.51,0.323 10 false A1A- 5.208,0.76 5.729,1.052 0.521,0.292 10 false HA1A 5.948,3.354 6.49,3.573 0.542,0.219 10 false ECM 3.417,2.042 4.76,2.188 1.344,0.146 10 false Air Fuel Ratio Sensor 6.365,1.292 6.844,1.656 0.479,0.365 10 false Duty Control



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
·

Open in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

A/F fuse

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor heater current reaches the high limit
(Hybrid IC high current limiter monitor input "Fail")
(1 trip detection logic).
·

Short in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

A/F fuse

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
·

Open in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

A/F fuse

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1) Air fuel ratio sensor heater current reaches the high limit
(Hybrid IC high current limiter monitor input "Fail")
(1 trip detection logic).
·

Short in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

A/F fuse

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P101D A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM Comes on DTC stored
P103D A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM Comes on DTC stored

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

P0031 and P0051
Heater output duty cycle 30% or higher

P0032 and P0052
Heater output duty cycle Higher than 0%

P101D and P103D
Both of the following conditions are met -
Heater output duty cycle 10% or higher, and less than 60%
Heater on current 0.8 A or higher

CONFIRMATION DRIVING PATTERN

A198819E49
0.749,0.969 1.396,1.162 0.647,0.193 10 3000 rpm 0.969,1.727 1.376,1.888 0.406,0.161 10 Idling 0.42,2.006 1.344,2.4 0.925,0.394 10 Ignition Switch ON 1.926,2.132 2.161,2.297 0.235,0.166 10 [A] 2.762,1.623 2.956,1.816 0.193,0.193 10 [B] 4.026,0.868 4.284,1.006 0.258,0.138 10 [C] 5.39,1.6 5.614,1.782 0.223,0.182 10 [D] 2.272,2.589 3.465,2.746 1.193,0.156 10 5 minutes or more 4.873,2.608 6.067,2.764 1.193,0.156 10 5 minutes or more 3.85,2.617 4.423,2.783 0.573,0.166 10 1 minute 5.98,3.028 6.183,3.231 0.203,0.203 10 [E]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine / DTC [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P0031, P0032, P0051, P0052, P101D or P103D.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F Heater Duty #1 and A/F Heater Duty #2].

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage (Click here Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
a.
A194092C05
0.375,2.208 0.833,2.479 0.458,0.271 0.385,1.823 0.833,2.094 0.448,0.271 1.906,1.938 2.365,1.646 false 0.198,0.135 0.833,0.573 0.635,0.438 10 *a 2.417,1.542 2.969,1.99 0.552,0.448 10 +B 0.896,2.229 1.448,2.615 0.552,0.385 10 *2 0.479,2.26 1.073,2.625 0.594,0.365 10 E48 0.896,1.844 1.49,2.24 0.594,0.396 10 *1 0.49,1.875 0.76,2.073 0.271,0.198 10 E19
*1 Bank 1
*2 Bank 2
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E19-2 (+B) - Body ground Ignition switch ON 11 to 14 V
E48-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E19-1 (HA1A) - E26-26 (HA1A) Always Below 1 Ω
E48-1 (HA2A) - E26-20 (HA2A) Always Below 1 Ω
E19-1 (HA1A) or E26-26 (HA1A) - Body ground Always 10 kΩ or higher
E48-1 (HA2A) or E26-20 (HA2A) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0051, P0052, P101D OR P103D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0051, P0052, P101D OR P103D)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the tester on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / DTC.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P0031, P0032, P0051, P0052, P101D or P103D is output B




A

B

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E19-2 (+B) - 1A-7 Always Below 1 Ω
E48-2 (+B) - 1A-6 Always Below 1 Ω
E19-2 (+B) or 1A-7 - Body ground Always 10 kΩ or higher
E48-2 (+B) or 1A-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
a.
A256530C06
0.729,1.146 1.146,1.385 0.417,0.24 0.146,0.083 0.563,0.479 0.417,0.396 10 *a 0.854,1.188 1.521,1.552 0.667,0.365 10 1D
*a Front view of wire harness connector
(to No. 1 Integration Relay)


Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1D-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)