Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0057  Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)  P0058  Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  P105D  O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON  


DESCRIPTION

Refer to DTC P0136 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0136).

HINT:

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

A256047E11
0.083,0.021 3.313,0.302 3.229,0.281 10 false Reference (System Diagram of Bank 1 Sensor 2) : 1.167,1.229 1.823,1.75 0.656,0.521 10 false EFI-MAIN NO. 1 2.104,2.385 2.896,2.625 0.792,0.24 10 false EFI MAIN 3.49,2.208 5.01,2.385 1.521,0.177 10 false Heated Oxygen Sensor 3.479,0.99 3.906,1.25 0.427,0.26 10 false +B 4.552,1 5.219,1.26 0.667,0.26 10 false HT1B 3.49,1.552 3.938,1.813 0.448,0.26 10 false E2 4.552,1.552 5.167,1.875 0.615,0.323 10 false OX1B 3.885,1.208 4.323,1.385 0.438,0.177 10 false Heater 3.875,1.844 4.333,2.021 0.458,0.177 10 false Sensor 5.823,3.469 6.146,3.646 0.323,0.177 10 false ECM 5.146,1 5.802,1.531 0.656,0.531 10 false HT1B 5.135,1.563 5.708,1.885 0.573,0.323 10 false OX1B 5.146,2.594 5.948,3.063 0.802,0.469 10 false EX1B 5.146,2.99 5.844,3.292 0.698,0.302 10 false MREL 0.156,1.073 1.281,1.375 1.125,0.302 10 false from Battery 2.927,1.229 3.833,1.521 0.906,0.292 10 false EFI NO. 3


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (bank 1 sensor 2) heater circuit

·

Heated oxygen sensor (bank 1 sensor 2)

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) Heated oxygen sensor heater current reaches high limit
(Hybrid IC high current limiter monitor input "Fail")
(1 trip detection logic).
·

Short in heated oxygen sensor (bank 1 sensor 2) heater circuit

·

Heated oxygen sensor (bank 1 sensor 2)

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (bank 2 sensor 2) heater circuit

·

Heated oxygen sensor (bank 2 sensor 2)

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) Heated oxygen sensor heater current reaches high limit
(Hybrid IC high current limiter monitor input "Fail")
(1 trip detection logic).
·

Short in heated oxygen sensor (bank 2 sensor 2) heater circuit

·

Heated oxygen sensor (bank 2 sensor 2)

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P102D O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM Comes on DTC stored
P105D O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM Comes on DTC stored

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check (P0037, P0038, P0057, P0058, P102D and P105D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.




MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

P0037 and P0057
Time after heater on 10 seconds or more

P0038 and P0058
Time after heater on 10 seconds or more

P102D and P105D
Time after heater on 10 seconds or more

CONFIRMATION DRIVING PATTERN

A198819E50
0.749,0.969 1.396,1.162 0.647,0.193 10 3000 rpm 0.969,1.739 1.376,1.9 0.406,0.161 10 Idling 0.417,2.006 1.346,2.345 0.929,0.339 10 Ignition Switch ON 1.926,2.132 2.161,2.297 0.235,0.166 10 [A] 2.762,1.623 2.956,1.816 0.193,0.193 10 [B] 4.026,0.868 4.284,1.006 0.258,0.138 10 [C] 5.39,1.6 5.614,1.782 0.223,0.182 10 [D] 2.272,2.589 3.465,2.746 1.193,0.156 10 5 minutes or more 4.873,2.608 6.067,2.764 1.193,0.156 10 5 minutes or more 3.85,2.617 4.423,2.783 0.573,0.166 10 1 minute 5.98,3.028 6.183,3.231 0.203,0.203 10 [E]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine / DTC [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P0037, P0038, P0057, P0058, P102D or P105D.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Refer to "Data List / Active Test" [O2 Heater B1S2, O2 Heater B2S2, O2 Heater Curr Val B1S2 and O2 Heater Curr Val B2S2].

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

When the values for the Data List items O2 Heater Curr Val B1S2 and O2 Heater Curr Val B2S2 are not 0 A, the heaters are on.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage (Click here Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
a.

Disconnect the heated oxygen sensor connector.

A255506C02
0.646,1.49 1.021,1.719 0.375,0.229 3.802,1.49 4.177,1.719 0.375,0.229 5.125,1.427 5.552,1.24 false 2.052,1.813 2.479,1.625 false 0.146,0.146 0.573,0.563 0.427,0.417 10 *a 5.604,1.167 6.063,1.531 0.458,0.365 10 +B 2.521,1.552 3.125,2.021 0.604,0.469 10 +B 0.708,1.531 1.281,2.01 0.573,0.479 10 E22 1.073,1.531 1.583,1.979 0.51,0.448 10 *1 3.875,1.531 4.365,1.885 0.49,0.354 10 E20 4.219,1.531 4.635,1.948 0.417,0.417 10 *2
*1 Bank 1 *2 Bank 2
*a Front view of wire harness connector
(to Heated Oxygen Sensor)
- -



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E22-2 (+B) - Body ground Ignition switch ON 11 to 14 V
E20-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-1 (HT1B) - E26-28 (HT1B) Always Below 1 Ω
E20-1 (HT2B) - E26-22 (HT2B) Always Below 1 Ω
E22-1 (HT1B) or E26-28 (HT1B) - Body ground Always 10 kΩ or higher
E20-1 (HT2B) or E26-22 (HT2B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0057, P0058, P102D OR P105D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0057, P0058, P102D OR P105D)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the tester on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / DTC.


j.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P0037, P0038, P0057, P0058, P102D or P105D is output B




A

B

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-2 (+B) - 1A-8 Always Below 1 Ω
E20-2 (+B) - 1A-8 Always Below 1 Ω
E22-2 (+B) or 1A-8 - Body ground Always 10 kΩ or higher
E20-2 (+B) or 1A-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR