Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074592 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the vehicle and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P or N and the brake pedal is depressed, the engine can be started by pressing the engine switch.

HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).

·

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.



CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / Trouble Codes.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Engine does not start
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

Shift P Signal

·

Neutral SW/ Clutch SW

·

Starter Request Signal


Entry&Start
·

L Code Check

·

Engine Start Request

·

Immobiliser


Starting Control
·

Ignition

·

Starter SW

·

Shift Position P or N


-


HINT:

If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal to illuminate the stop lights increases.


PROCEDURE

1.CHECK BATTERY
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:
·

It may be possible to tell whether the vehicle battery is discharged by operating the horn.

·

If the battery voltage is less than 11 V, charge or replace it.




Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Using the intelligent tester, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.



Result:
Proceed to
OK
NG



OK

3.CHECK WAVE ENVIRONMENT

NG

GO TO DTC CHART

3.CHECK WAVE ENVIRONMENT
a.

If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

HINT:

Whether or not the problem is due to wave interference can be checked by holding the electrical key transmitter near the door control receiver (RF band).



Result:
Proceed to
NEXT



NEXT

4.CHECK ENGINE SWITCH CONDITION
4.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the engine switch causes the power source mode to change.

Result:
Result Proceed to
Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) and on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D




A

5.CHECK CRANKING FUNCTION

B

C

D

5.CHECK CRANKING FUNCTION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Depress the brake pedal.


d.

Confirm that the smart warning light is displayed , and then press the engine switch and check that the engine cranks.

OK:

Engine cranks.



Result:
Result Proceed to
OK A
NG B



A

6.CHECK SECURITY INDICATOR LIGHT (ENGINE IMMOBILISER SYSTEM UNSET)

B

GO TO SFI SYSTEM (PROBLEM SYMPTOMS TABLE)

6.CHECK SECURITY INDICATOR LIGHT (ENGINE IMMOBILISER SYSTEM UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

OK:

Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


HINT:

It is determined that the engine immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

7.CHECK COMBINATION METER ASSEMBLY

NG

19.CHECK STEERING LOCK
7.CHECK COMBINATION METER ASSEMBLY
a.

Get into the vehicle while carrying the electrical key transmitter sub-assembly, move the shift lever to P, press the engine switch while depressing the brake pedal and check that the combination meter indicator changes.

OK:

The smart warning light is displayed.


HINT:

If the smart warning light is displayed when the procedure above is performed, the P, N and brake signals can be considered to be normal.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING INTELLIGENT TESTER (STARTER SW)

NG

13.READ VALUE USING INTELLIGENT TESTER (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
8.READ VALUE USING INTELLIGENT TESTER (STARTER SW)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Starting Control / Data List.


e.

Get into the vehicle while carrying an electrical key transmitter sub-assembly and press the engine switch with the shift lever in P and brake pedal depressed to check if the Data List display changes.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request ON orOFF ON: Starter operation requested
OFF: Starter operation not requested
When malfunctioning, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The Data List item changes.



Result:
Proceed to
OK
NG



OK

9.INSPECT ST RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.INSPECT ST RELAY
a.
B060778N17
2.531,1.604 3.01,1.604 false 2.531,1.104 2.979,1.104 false 2.667,0.708 3.01,0.708 false 2,0.719 1.76,0.719 false 3.073,1.51 3.26,1.708 0.188,0.198 10 3 0.146,0.719 0.281,0.917 0.135,0.198 10 3 1.198,0.719 1.396,0.917 0.198,0.198 10 5 3.094,1.021 3.271,1.219 0.177,0.198 10 5 0.156,1.25 0.292,1.448 0.135,0.198 10 2 3.083,0.583 3.26,0.781 0.177,0.198 10 2 1.219,1.25 1.396,1.448 0.177,0.198 10 1 1.542,0.625 1.677,0.823 0.135,0.198 10 1

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 93.8 to 136.4 Ω
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



c.

Reinstall the ST relay to the engine room relay block and junction block assembly.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

NG

REPLACE ST RELAY

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.
B268625C22
0.091,0.052 0.277,0.214 0.186,0.161 10 *a 0.241,1.304 0.729,1.597 0.487,0.292 0.334,1.362 0.63,1.518 0.296,0.157 10 A43 1.581,1.469 1.1,1.9 false 0.948,1.916 1.311,2.062 0.363,0.146 10 STA 1.859,1.471 2.245,1.863 false 2.031,1.873 2.585,2.019 0.554,0.146 10 STAR
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the A43 connector from the certification ECU (smart key ECU assembly).


b.

Move the shift lever to P or N.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-5 (STAR) - Body ground 20°C (68°F) 93.75 to 136.36 Ω
A43-7 (STA) - Body ground



Result:
Proceed to
OK
NG



OK

11.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT STARTER ASSEMBLY
a.

Remove the starter assembly.

Click hereEngine / Hybrid System>2GR-FE STARTING>STARTER>REMOVAL


b.

Inspect the starter assembly.

Click hereEngine / Hybrid System>2GR-FE STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY AND ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY AND ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
a.

Remove the starter assembly from the vehicle to perform an inspection.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F2-1 (B) - Body ground Always 11 to 14 V
5 - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - E9-1 (ST) Always Below 1 Ω
3 or E9-1 (ST) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.READ VALUE USING INTELLIGENT TESTER (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control or Starting Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P and N) ON or OFF ON: Shift lever in P or N
OFF: Shift lever in any position other than P or N
·

Use this item to determine whether the park/neutral position switch is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/neutral position switch status ON or OFF ON: Shift lever in P or N
OFF: Shift lever in any position other than P or N
When malfunctioning, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2
OK:

The item in the Data List changes according to the shift position.



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH1)

NG

17.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY
14.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The item in the Data List changes when the brake pedal is depressed and released.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

15.INSPECT STOP LIGHT SWITCH ASSEMBLY
15.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Disconnect the A33 connector from the stop light switch assembly.


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Disconnect the E4 park/neutral position switch assembly connector.


b.
A125187C04
1.222,0.954 0.832,0.914 false 1.344,1.389 1.046,1.718 false 0.889,1.712 1.016,1.859 0.126,0.147 10 L 0.672,0.834 0.812,0.981 0.14,0.147 10 B 0.162,0.132 0.554,0.364 0.392,0.232 10 *a
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
Shift lever in any position other than P or N 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

NG

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the A43 connector from the certification ECU (smart key ECU assembly).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-5 (STAR) - E4-4 (B) Always Below 1 Ω
A43-5 (STAR) or E4-4 (B) - Body ground Always 10 kΩ or higher



c.

Reconnect the E4 park/neutral position switch assembly connector.


d.
B268625C23
0.091,0.052 0.277,0.214 0.186,0.161 10 *a 0.241,1.304 0.729,1.597 0.487,0.292 0.334,1.362 0.63,1.518 0.296,0.157 10 A43 1.859,1.471 2.245,1.863 false 2.031,1.873 2.585,2.019 0.554,0.146 10 STAR
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-5 (STAR) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Engine switch released after approximately 1 second elapses (starter off) 6 V or higher* → 1.5 V or less


HINT:

*: When the engine is cranking, the battery voltage may momentarily drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK STEERING LOCK
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

20.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER)

NG

22.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)
20.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system determined by certification ECU (smart key ECU assembly) Set or Unset Set: Engine immobiliser system set (engine start prohibited) (engine switch off)
Unset: Engine immobiliser system unset (engine start permitted) (engine switch on (ACC) or on (IG))
The engine cannot be started when Set is displayed.
HINT:
·

The security indicator light blinks when Set is displayed.

·

The security indicator light is linked with set/unset of the immobiliser and not linked with steering lock/unlock.



Body Electrical > Entry&Start > Data List
Tester Display
Immobiliser
50003 125 34
OK:

The Data List item changes to "unset" when the engine switch is turned on (ACC) or on (IG).



Result:
Proceed to
OK
NG



OK

21.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

21.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status ON or OFF ON: With the shift lever in P and brake pedal depressed, the engine switch is pressed and held
OFF: After approximately. 1 second. has elapsed, the engine switch is released
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the smart warning is displayed on the multi-information display on the combination meter assembly, and then press the engine switch.


OK:

The display changes in response to the operation of the engine switch.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

22.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly ON or OFF ON: Steering unlocked
OFF: Steering locked
·

When the shift lever is in P and the engine switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter sub-assembly is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.


Body Electrical > Power Source Control > Data List
Tester Display
Steering Unlock Switch
50003 223 2
OK:

The item in the Data List indicates "ON" (the steering is unlocked).



Result:
Proceed to
OK
NG



OK

GO TO STEERING LOCK SYSTEM (UNABLE TO UNLOCK STEERING WHEEL)

NG

23.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
23.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

L code has not been registered for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly).

·

Steering cannot be locked.

·

Steering cannot be unlocked (the engine cannot be started).


OK:

The Data List item changes to "OK" when the electrical key transmitter sub-assembly is inside the vehicle.


HINT:

Reasons for verification failure:

·

The steering lock ECU is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

24.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

25.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
24.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform the registration procedures (Refer to the Service Bulletin).


c.

Turn the engine switch on (IG).


d.

Operate the steering wheel and check the steering condition.


Result:
Proceed to
NEXT



NEXT

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE)

25.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform the registration procedures (Refer to the Service Bulletin).


c.

Use the Data List to check if L code certification is functioning properly again.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

L code has not been registered for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly).

·

Steering cannot be locked.

·

Steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK (L code certification result normal) appears on the screen.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)