Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM2030EQ _58 Vehicle Interior _014672 HEATING / AIR CONDITIONING _0074651 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the air conditioning amplifier assembly is turned on, a magnetic clutch on signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the engine room junction block assembly turns on to operate the magnetic clutch assembly.

WIRING DIAGRAM

E227683E04
6.125,3.021 6.583,3.448 0.458,0.427 10 MGC 5.875,5.625 7.052,6.104 1.177,0.479 10 Air Conditioning Amplifier Assembly 5.021,3.688 5.344,3.958 0.323,0.271 10 3 4.802,4.271 5.396,4.615 0.594,0.344 10 1 4.01,4.448 4.615,5.052 0.604,0.604 10 Magnetic Clutch Assembly 3.885,5.646 5.75,5.969 1.865,0.323 10 Cooler Compressor Assembly 1.99,5.51 3.427,5.917 1.438,0.406 10 Engine Room Junction Block Assembly 5.823,2.896 6.146,3.302 0.323,0.406 10 20 5.875,5.469 6.177,5.646 0.302,0.177 10 I77 4.01,4.281 4.313,4.427 0.302,0.146 10 a2 3.885,5.479 4.385,5.677 0.5,0.198 10 E73 4.99,3.927 5.521,4.25 0.531,0.323 10 MG+ 2.927,2.323 3.552,2.771 0.625,0.448 10 MGCT 3.458,2.344 4.104,2.677 0.646,0.333 10 1M 3.49,3.01 3.958,3.375 0.469,0.365 10 1F 1.688,2.344 1.938,2.625 0.25,0.281 10 A 1.698,2.146 2.063,2.573 0.365,0.427 10 1 1.698,2.802 2.042,3.125 0.344,0.323 10 1 3.5,2.146 4.083,2.458 0.583,0.313 10 1 3.521,2.802 3.979,3.073 0.458,0.271 10 9 1.656,3.469 2.042,3.885 0.385,0.417 10 15 1.698,4.125 1.969,4.417 0.271,0.292 10 3 1.698,4.792 2.01,5.063 0.313,0.271 10 4 1.271,0.625 2.49,0.885 1.219,0.26 10 ECU-IG1 NO. 1 2.844,1.354 3.979,1.792 1.135,0.438 10 from Battery 2.844,0.448 4.469,0.823 1.625,0.375 10 from IG1 NO. 2 Relay 2.844,0.896 4.083,1.333 1.24,0.438 10 from ALT Fuse 1.698,3.01 2.042,3.448 0.344,0.438 10 B 2.927,2.99 3.615,3.323 0.688,0.333 10 MCLS 1.99,2.344 2.49,2.5 0.5,0.156 10 BATT 1.99,3.021 2.656,3.365 0.667,0.344 10 ALT 1.656,3.667 1.927,4.021 0.271,0.354 10 1F 1.656,4.333 2.042,4.677 0.385,0.344 10 1F 1.979,3.667 2.781,4.073 0.802,0.406 10 IGN 1.979,4.354 2.719,4.677 0.74,0.323 10 GND1 1.646,4.99 2.083,5.24 0.438,0.25 10 1G 1.979,4.99 2.417,5.271 0.438,0.281 10 GND2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Using a voltmeter, check the signal reading of the engine room junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

A normal signal reading is output.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - POWER SOURCE AND BODY GROUND)

NG

INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULT OF SIGNAL READING CHECK)

2.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.

Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL

E230000C12
2.781,2.615 3.094,2.813 0.313,0.198 4.729,2.708 5.042,2.906 0.313,0.198 6.188,3.094 6.5,3.292 0.313,0.198 0.771,3.073 1.083,3.271 0.313,0.198 5.104,3.656 5.271,3.979 false 0.865,3.583 0.792,3.896 false 2.625,3.656 2.563,4.104 false 6.281,3.625 6.219,3.948 false 2.865,2.635 3.083,2.833 0.219,0.198 10 false 1F 4.802,2.729 5.021,2.927 0.219,0.198 10 false 1G 6.302,3.115 6.5,3.313 0.198,0.198 10 false A 0.885,3.094 1.01,3.26 0.125,0.167 10 false B 0.271,0.208 0.479,0.406 0.208,0.198 10 false *a 6.083,3.969 6.479,4.156 0.396,0.188 10 false BATT 5.115,4 5.573,4.188 0.458,0.188 10 false GND2 2.344,4.115 2.771,4.281 0.427,0.167 10 false GND1 0.646,3.927 0.938,4.115 0.292,0.188 10 false ALT
*a Component without engine room junction block assembly
(Engine Room Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 (BATT) - Body ground Always 11 to 14 V
B-1 (ALT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-3 (GND1) - Body ground Always Below 1 Ω
1G-4 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - MAGNETIC CLUTCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - MAGNETIC CLUTCH ASSEMBLY)
a.

Disconnect the E73 cooler compressor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1M-1 (MGCT) - E73-3 (MG+) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT COOLER COMPRESSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT COOLER COMPRESSOR ASSEMBLY
a.

Remove the engine room junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Disconnect the a2 magnetic clutch assembly connector.


c.
E228787C05
1.5,0.115 1.958,0.396 0.458,0.281 1.5,2.01 1.958,2.292 0.458,0.281 1.76,1.417 2.594,1.417 false 1.583,0.167 1.875,0.333 0.292,0.167 10 false E73 1.635,2.063 1.823,2.229 0.188,0.167 10 false a2 2.698,1.323 3.146,1.646 0.448,0.323 10 false MG+ 0.5,0.177 0.667,0.323 0.167,0.146 10 false *a 0.5,1.792 0.667,1.938 0.167,0.146 10 false *b
*a Component without harness connected
(Cooler Compressor Assembly)
*b Component without harness connected
(Magnetic Clutch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E73-3 (MG+) - a2-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAGNETIC CLUTCH ASSEMBLY

NG

REPLACE COOLER COMPRESSOR ASSEMBLY

5.INSPECT MAGNETIC CLUTCH ASSEMBLY
a.
E167401C02
0.374,0.245 0.641,0.582 0.267,0.336 10 *a 0.91,1.823 1.103,1.969 0.193,0.147 10 a2 0.812,1.783 1.225,2.04 0.413,0.258
*a Component without harness connected
(Magnetic Clutch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a2-1 - Body ground 20°C (68°F) 3.8 to 4.2 Ω



b.

When connector terminal a2-1 is connected to a positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch operating sound can be heard, and 2) the magnetic clutch hub and rotor lock.


Result:
Proceed to
OK
NG



OK

6.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

REPLACE MAGNETIC CLUTCH ASSEMBLY

6.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Disconnect the I77 air conditioning amplifier assembly connector.


b.

Reconnect the engine room junction block assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I77-20 (MGC) - Body ground Ignition switch off Below 1 V
I77-20 (MGC) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
7.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the I77 air conditioning amplifier assembly connector.


b.
E227427C30
0.182,0.168 0.341,0.317 0.159,0.149 10 *a 0.604,1.549 0.961,1.698 0.358,0.149 10 MGC 1.277,0.296 1.74,0.582 0.463,0.286 1.393,0.353 1.696,0.509 0.303,0.156 10 I77 0.932,1.013 0.778,1.531 false
*a Component without harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage and voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I77-20 (MGC) - Body ground Ignition switch ON
A/C switch: off
11 to 14 V
I77-20 (MGC) - Body ground Ignition switch off
A/C switch: on
Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
a.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I77-20 (MGC) - 1F-9 (MCLS) Always Below 1 Ω
I77-20 (MGC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR