1.REMOVE FRONT SEAT ASSEMBLY RH
67913
2.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62311B
3.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL
67917A
4.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62331A
5.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL
73233
6.REMOVE LAP BELT OUTER ANCHOR COVER
Use the same procedure as for the LH side.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL
73210
7.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL
62413A
8.REMOVE CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
67918A
9.REMOVE REAR DOOR SCUFF PLATE LH
10.REMOVE REAR SEAT CUSHION ASSEMBLY
72693
11.REMOVE REAR SEAT CUSHION LOCK HOOK
12.REMOVE REAR SIDE SEATBACK ASSEMBLY LH
64711
13.REMOVE LUGGAGE COMPARTMENT FLOOR MAT
58387
14.REMOVE REAR FLOOR FINISH PLATE
64725D
15.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
64722
16.REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH
77306
17.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
77035
18.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
Disengage the 2 clamps.
Disengage the clamp and disconnect the wire harness.
Disengage the 2 clamps and remove the 2 scuff plate clips.
Turn back the floor carpet so that the fuel lid lock control cable sub-assembly can be removed.
| *1 | Tape |
| *2 | Fuel Lid Lock Control Cable Sub-assembly |
| *3 | Luggage Door Lock Control Cable Sub-assembly |
Remove the 2 pieces of tape that connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.
Remove the No. 2 noise control plate.
| *1 | Cutout |
| *2 | Guide <A> |
Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts with the guides <A>, and then pull the fuel filler opening lid lock retainer.
| *1 | Cutout |
| *2 | Guide <B> |
Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts with guides <B>, and then pull the fuel filler opening lid lock retainer.
| *1 | Cutout |
| *2 | Guide <C> |
| *3 | Guide <B> |
Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.
Disengage the 2 claws and remove the fuel filler opening lid lock retainer.
Disengage the 7 clamps and remove the fuel lid lock control cable sub-assembly.
| *1 | Fuel Lid Lock Control Cable Sub-assembly | *2 | Luggage Door Lock Control Cable Sub-assembly |