Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2013.07
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074417 ENGINE UNIT A

2GR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly and oil filler cap gasket.


Hide 12101A 3.REMOVE OIL PAN DRAIN PLUG

a.
A129654

Remove the oil pan drain plug and oil pan drain plug gasket.


Hide 12204 4.REMOVE VENTILATION VALVE SUB-ASSEMBLY

a.
A129655

Remove the ventilation valve sub-assembly.


Hide 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 15771 8.REMOVE NO. 1 OIL PIPE

a.
A306358C01
1.979,1.906 2.292,2.104 0.313,0.198 10 false *1 1.354,0.771 1.667,0.969 0.313,0.198 10 false *1
*1 Oil Pipe Union


Remove the 2 oil pipe unions, 3 gaskets and No. 1 oil pipe.


b.

Remove the oil control valve filter LH.


Hide 15771M 9.REMOVE OIL PIPE

a.
A200607C06
1.677,0.604 1.844,0.76 0.167,0.156 10 false *1 1.521,1.667 1.75,1.823 0.229,0.156 10 false *1 2.344,1.135 2.583,1.302 0.24,0.167 10 false *2
*1 Oil Pipe Union
*2 Bolt


Remove the bolt.


b.

Remove the 2 oil pipe unions, 3 gaskets and oil pipe.


c.

Remove the oil control valve filter RH.


Hide 11415 10.REMOVE TAPER SCREW PLUG

HINT:

Perform this operation only when a taper screw plug is installed.


a.
A292824

Remove the taper screw plug from the cylinder block sub-assembly.


Hide 11415 11.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

A305214C01
0.094,0.083 0.406,0.281 0.313,0.198 12 false *A 0.094,1.729 0.406,1.927 0.313,0.198 12 false *B
*A for Bank 1
*B for Bank 2


a.

for Bank 1:

i.

Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.


ii.

Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.



b.

for Bank 2:

HINT:

Perform this operation only when a cylinder block water drain cock sub-assembly is installed.


i.

Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.


ii.

Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.



Hide 04152 12.REMOVE OIL FILTER CAP ASSEMBLY

Hide 15710 14.REMOVE OIL COOLER ASSEMBLY

Hide 15781 15.REMOVE NO. 1 OIL COOLER BRACKET

a.
A268434

Remove the 3 bolts, 3 nuts, gasket and No. 1 oil cooler bracket together with the oil cooler pipe.


b.

Using an E7 "TORX" socket wrench, remove the stud bolt.


c.
A268435C05
2.563,1.198 2.74,1.354 0.177,0.156 10 false *1 2.906,1.021 3.083,1.177 0.177,0.156 10 false *2 2.823,0.427 3,0.583 0.177,0.156 10 false *1
*1 Nut
*2 Bolt


Remove the bolt, 2 nuts, No. 1 oil cooler bracket, and gasket.


d.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.


Hide 11452 16.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A210128

Remove the engine oil level dipstick guide.


b.
A171897

Remove the O-ring.


Hide 12315 17.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.
A129672

Remove the 6 bolts and front No. 1 engine mounting bracket LH.


b.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.


Hide 16323 18.REMOVE WATER INLET HOUSING

a.
A129673

Remove the 2 nuts, water inlet and thermostat.


b.

Remove the gasket.


c.

Remove the 2 stud bolts.


d.

Slide the clip and disconnect the No. 1 water by-pass hose from the water inlet housing.


e.
A307377C01
1.021,1.333 1.333,1.531 0.313,0.198 10 false *1 1.969,0.573 2.281,0.771 0.313,0.198 10 false *2 1.813,1.948 2.125,2.146 0.313,0.198 10 false *2
*1 Nut
*2 Bolt


Remove the drain cock plug.


f.

Remove the drain cock assembly.


g.

Remove the 2 bolts, nut, and water inlet housing.


h.
A129675

Remove the 2 O-rings.


Hide 16331 19.REMOVE WATER OUTLET

a.
A268436C05
0.896,0.396 1.063,0.563 0.167,0.167 10 false *1 0.823,1.552 0.99,1.719 0.167,0.167 10 false *1 2.646,1.396 2.813,1.563 0.167,0.167 10 false *1 2.458,0.333 2.625,0.5 0.167,0.167 10 false *1 1.917,1.521 2.083,1.688 0.167,0.167 10 false *2 1.531,1.542 1.698,1.708 0.167,0.167 10 false *2
*1 Nut
*2 Bolt


Remove the 2 bolts, 4 nuts and water outlet.


b.
A129677

Remove the 2 gaskets and O-ring.


Hide 11201 20.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A129679C04
1.438,0.792 1.677,0.792 1.677,0.792 1.875,1.115 true 1.25,0.688 1.563,0.885 0.313,0.198 10 false *1
*1 Seal Washer


Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.


b.
A129699

Remove the 3 gaskets.


Hide 11202 21.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A293123C03
2.448,0.875 2.563,0.875 2.563,0.875 2.979,1.01 true 1.781,1.083 1.885,0.875 1.885,0.875 1.958,0.875 false 2.271,0.813 2.635,1.104 0.365,0.292 10 false *1 1.99,0.802 2.354,1.094 0.365,0.292 10 false *2
*1 Baffle Plate
*2 Seal Washer


Remove the 12 bolts, seal washer, cylinder head cover sub-assembly LH and No. 2 cylinder head cover gasket.

NOTICE:

The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the cylinder head cover sub-assembly LH.



b.
A129705

Remove the 3 gaskets.


Hide 12102A 22.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A306210C01
0.344,1.667 0.656,1.865 0.313,0.198 10 false *1 2.458,0.531 2.771,0.729 0.313,0.198 10 false *1
*1 Nut


Remove the 16 bolts and 2 nuts.


b.
A120816

Insert the blade of on oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.



c.

Using an E6 "TORX" socket wrench, remove the 2 stud bolts.


Hide 15104 23.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A129681C03
2.406,1.323 2.573,1.49 0.167,0.167 10 *1 1,1.813 1.167,1.979 0.167,0.167 10 *2 1.167,0.802 1.333,0.969 0.167,0.167 10 *2
*1 Bolt
*2 Nut


Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.


b.

Using an E6 "TORX" socket wrench, remove the 2 stud bolts.


Hide 12101 24.REMOVE OIL PAN SUB-ASSEMBLY

a.
A376238C03
0.292,0.073 0.656,0.313 0.365,0.24 12 false *A 0.292,2.406 0.656,2.677 0.365,0.271 12 false *B
*A Type A
*B Type B
V100135

Bolt
V100136

Nut


Remove the 16 bolts and 2 nuts.

HINT:

Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.



b.
A129683C04
0.625,0.677 1.823,0.229 false 0.563,2.813 0.375,2.667 false 2.833,2.552 3.156,2.479 false 1.906,0.104 2.094,0.281 0.188,0.177 10 false *a 0.177,2.531 0.365,2.708 0.188,0.177 10 false *a 3.177,2.375 3.365,2.552 0.188,0.177 10 false *a
*a Protective Tape


Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A129684

Remove the 2 O-rings.


d.

Using an E8 "TORX" socket wrench, remove the 4 stud bolts.

A376289C02
0.219,0.042 6.948,2.25 6.729,2.208 0.219,2.302 6.948,4.51 6.729,2.208 0.271,0.104 0.604,0.313 0.333,0.208 12 false *A 0.281,2.438 0.656,2.698 0.375,0.26 12 false *B 1.521,0.104 1.833,0.26 0.313,0.156 10 false *a 5.5,0.094 5.813,0.25 0.313,0.156 10 false *b 1.479,4.75 1.792,4.906 0.313,0.156 10 false *c 3.094,2.396 3.406,2.552 0.313,0.156 10 false *b
*A Type A *B Type B
*a Timing Chain Cover Sub-assembly Side *b Cylinder Block Sub-assembly Bottom Side
*c Oil Pan Sub-assembly LH Side - -



Hide 12121 25.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A129685

Remove the 7 bolts and No. 1 oil pan baffle plate.


Hide 11381 26.REMOVE ENGINE REAR OIL SEAL RETAINER

a.
A129686

Remove the 6 bolts.


b.
A304100C05
0.792,1.219 0.896,1.219 0.896,1.219 1.25,1.01 true 0.594,1.125 0.906,1.323 0.313,0.198 10 false *a
*a Protective Tape
V100135

Pry


Using a screwdriver, pry out the engine rear oil seal retainer.

NOTICE:

Be careful not to damage the engine rear oil seal retainer.


HINT:

Tape the screwdriver tip before use.



Hide 11381A 27.REMOVE ENGINE REAR OIL SEAL

a.
A131834C03
0.99,1.75 0.635,1.958 0.635,1.958 2.344,2.021 false 1.49,1.354 0.844,0.635 false 0.625,0.51 0.896,0.698 0.271,0.188 10 false *a 0.417,1.865 0.625,2.052 0.208,0.188 10 false *b
*a Protective Tape
*b Wooden Block


Place the engine rear oil seal retainer on wooden blocks.


b.

Using a screwdriver and a hammer, tap out the engine rear oil seal.

NOTICE:

Be careful not to damage the engine rear oil seal retainer.


HINT:

Tape the screwdriver tip before use.



Hide 16100 28.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A129688

Remove the 16 bolts, engine water pump assembly and water pump gasket.


Hide 11302 29.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A129689C02
2.515,1.723 2.682,1.875 0.167,0.152 10 *1 0.744,1.927 0.911,2.079 0.167,0.152 10 *1
*1 Nut


Remove the 15 bolts and 2 nuts shown in the illustration.


b.
A129690C05
0.469,3.958 1.323,4.219 1.323,4.219 2.885,3.969 false 1.885,0.677 0.729,2.24 0.729,2.24 0.729,1.104 false 2.469,0.99 0.729,2.24 false 0.583,2.292 0.833,2.521 0.25,0.229 10 false *a 1.219,4.25 1.396,4.448 0.177,0.198 10 false *a
*a Protective Tape


Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.

Remove the 4 bolts, timing chain cover plate and timing chain cover plate gasket.


d.
A128006

Remove the gasket.


Hide 11301C 30.REMOVE TIMING CHAIN CASE OIL SEAL

Hide 31.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily tighten the crankshaft pulley set bolt.


b.
A205165C07
0.635,0.615 0.385,1.521 0.385,1.521 1.594,0.938 false 0.458,0.198 0.708,0.198 false 1.906,1.917 2.156,2.031 false 0.76,0.125 0.938,0.292 0.177,0.167 10 false *b 0.229,1.531 0.406,1.698 0.177,0.167 10 false *c 2.198,1.958 2.479,2.156 0.281,0.198 10 false *a
*a Sensor Plate
*b Center Line
*c Timing Mark


Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).


c.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned with the timing marks of the camshaft bearing caps as shown in the illustration.

A293128C03
6.052,2.792 5.594,3.25 5.594,3.25 4.938,2.938 false 4.927,2.469 5.604,3.25 5.604,3.25 6.073,2.51 false 1.156,0.677 1.594,1.427 1.594,1.427 2.427,0.74 false 1.167,1 1.583,1.427 1.583,1.427 2.438,1.177 false 5.521,3.302 5.833,3.5 0.313,0.198 10 *a 1.521,1.427 1.833,1.625 0.313,0.198 10 *a
*a Timing Mark - -


If not, turn the crankshaft 1 revolution (360°) clockwise and align the timing marks as above.


Hide 13540 32.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A124589C10
2.635,1.177 1.885,1.823 1.885,1.823 1.135,1.177 true 2.802,0.875 2.802,0.135 2.802,0.135 0.885,0.135 true 1.125,0.135 1.125,0.865 true 2.677,1.865 2.938,1.865 true 0.688,0.073 0.99,0.323 0.302,0.25 10 false *a 1.833,1.875 2.083,2.135 0.25,0.26 10 false *b 3,1.823 3.26,2.042 0.26,0.219 10 true *c
*a Plunger
*b Stopper Plate
*c Pin


Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.


b.

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.
A095165

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 33.REMOVE CHAIN TENSIONER SLIPPER

a.

Remove the chain tensioner slipper.


Hide 13506 34.REMOVE CHAIN SUB-ASSEMBLY

a.
A211711C04
0.438,0.156 0.646,0.146 false 2,1.896 2.198,2.042 false 0.51,0.688 0.385,1.615 0.385,1.615 1.594,0.927 false 0.115,0.667 0.438,0.823 0.323,0.156 10 false 10° 0.667,0.063 0.854,0.24 0.188,0.177 10 false *b 0.229,1.625 0.427,1.823 0.198,0.198 10 false *c 2.24,1.958 2.396,2.104 0.156,0.146 10 false *a
*a Sensor Plate
*b Center Line
*c Timing Mark


Turn the crankshaft 10° counterclockwise to loosen the chain sub-assembly off the crankshaft timing sprocket.


b.

Remove the crankshaft pulley set bolt.


c.
A134890

Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.


d.
A293117C03
0.083,0.083 0.396,0.281 0.313,0.198 12 false *A
*A for Bank 1


Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) and set it as shown in the illustration.

NOTICE:

Be sure to loosen the chain sub-assembly between the banks.



e.

Remove the chain sub-assembly.


Hide 13530 35.REMOVE IDLE SPROCKET ASSEMBLY

a.
A129695

Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.


Hide 13561 36.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A129696

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13562 37.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.

Remove the 2 No. 2 chain vibration dampers.


Hide 13521 38.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A109720

Remove the crankshaft timing sprocket from the crankshaft.


b.

Remove the 2 keys from the crankshaft.


Hide 39.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

Hide 13550 40.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 41.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

Hide 13512 43.REMOVE NO. 2 CAMSHAFT

Hide 11103C 44.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

Hide 45.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

Hide 13560A 46.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 47.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

Hide 13053 48.REMOVE NO. 3 CAMSHAFT

Hide 13054 49.REMOVE NO. 4 CAMSHAFT

Hide 11104A 50.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 13801 51.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 52.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 54.REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

Hide 11115 55.REMOVE CYLINDER HEAD GASKET RH

Hide 11102 56.REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

Hide 11116 57.REMOVE CYLINDER HEAD GASKET LH

Hide 16322 58.REMOVE WATER INLET PIPE

a.

Slide the clip and disconnect the No. 1 water by-pass hose from the water inlet pipe.


b.
A268438

Remove the 2 bolts and water inlet pipe.