1. PRECAUTION
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67914
3.REMOVE FRONT DOOR SCUFF PLATE LH
62112A
4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
62312B
5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Disconnect the front door opening trim weatherstrip LH.
55318C
6.REMOVE INSTRUMENT SIDE PANEL LH
Using a moulding remover, disengage the 4 claws as shown in the illustration.
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
55431B
7.REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)
Disengage the 2 claws and 4 clips as shown in the illustration.
Disconnect the connector to remove the upper instrument panel finish panel.
55650
8.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.
55410C
9.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.
Using a moulding remover, disengage the 4 clips and 2 guides.
for LHD:
Disengage the 3 claws, 7 clips and 4 guides.
for RHD:
Disengage the 4 claws, 5 clips and 4 guides.
Disconnect each connector.
Remove the instrument cluster finish panel assembly as shown in the illustration.
83100
10.REMOVE COMBINATION METER ASSEMBLY
53922B
11.REMOVE FRONT PANEL GARNISH LH
Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.
53601
12.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
55432D
13.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
for LHD:
Remove the 2 bolts <B>.
Disengage the 5 clips and 3 guides to remove the lower No. 1 instrument panel finish panel.
for RHD:
Remove the 2 bolts <B>.
Disengage the 4 claws, 9 clips and 3 guides.
Disconnect each connector and remove the lower No. 1 instrument panel finish panel.
53921B
14.REMOVE FRONT PANEL GARNISH RH
Disengage the 3 clips and 8 guides to remove the front panel garnish RH as shown in the illustration.
33504F
15.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
58805C
16.REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
58801E
17.REMOVE UPPER CONSOLE BOX SUB-ASSEMBLY
58864B
18.REMOVE NO. 4 CONSOLE BOX DUCT
58815A
19.REMOVE CONSOLE BOX CARPET
20.REMOVE CONSOLE BOX ASSEMBLY
55405B
21.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Using a moulding remover, pry up on the center instrument cluster finish panel sub-assembly until there is enough of a gap to make it possible to pull on the panel by hand.
Pull the center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 7 clips and 2 guides and remove the center instrument cluster finish panel sub-assembly as shown in the illustration.
55660
22.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 4 clips as shown in the illustration.
Disconnect the connector to remove the No. 2 instrument panel register assembly.
58831A
23.REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Disengage the 2 claws as shown in the illustration.
Disconnect each connector to remove the front console upper panel garnish.
74110E
24.REMOVE FRONT ASH RECEPTACLE ASSEMBLY
Remove the 2 screws <C>.
Disengage the 2 clips as shown in the illustration.
Disconnect each connector to remove the front ash receptacle assembly.
25.REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)
26.REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)
67913
27.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62111A
28.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62311B
29.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Disconnect the front door opening trim weatherstrip RH.
55317A
30.REMOVE INSTRUMENT SIDE PANEL RH
Using a moulding remover, disengage the 4 claws as shown in the illustration.
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
55607
31.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Disengage the 4 claws.
Disengage the 2 guides.
Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.
55303B
32.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Remove the bolt <B> and screw <C>.
Open the lower instrument panel door.
Remove the 3 screws <C>.
Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.
55670
33.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
Using a moulding remover, disengage the 10 clips to remove the No. 3 instrument panel register assembly as shown in the illustration.
62212
34.REMOVE FRONT PILLAR GARNISH LH
55408F
35.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 clips and 3 claws.
Disengage the 2 guides to remove the No. 1 instrument panel speaker panel sub-assembly.
86160P
36.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
55510F
37.REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY
Disengage the 6 clips as shown in the illustration.
Disconnect the connector to remove the No. 1 speaker opening cover assembly.
86160J
38.REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)
62211
39.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
55409F
40.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 clips and 3 claws.
Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly.
86160P
41.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
58817A
42.REMOVE FRONT NO. 2 CONSOLE BOX INSERT
Remove the 2 screws <C>.
Disengage the clip and 4 guides to remove the front No. 2 console box insert as shown in the illustration.
for LHD:
Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.
58816B
43.REMOVE CONSOLE BOX INSERT
Remove the 2 screws <C>.
Disengage the clip and 4 guides to remove the console box insert as shown in the illustration.
for RHD:
Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.
55480D
44.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
for LHD:
Disengage the 3 clips and guide.
Disconnect the connector to remove the lower instrument panel finish panel assembly.
for RHD:
Disengage the 3 clips and guide to remove the lower instrument panel finish panel assembly.
55011A
45.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Disengage the 10 clips to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
82142A
46.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE
47.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Disconnect each connector.
Disengage each clamp.
Disconnect the glove box light as shown in the illustration.
Remove the 2 passenger airbag bolts <A>.
| *1 | Passenger Airbag Bolt <A> | *2 | Bolt <B> |
| *3 | Nut <D> | *4 | Clip |
Remove the 3 bolts <B> and nut <D> .
Remove the 2 clips.
Disengage the 5 guides and remove the instrument panel safety pad assembly as shown in the illustration.
Do not damage the instrument panel safety pad assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.