When replacing the windshield glass of a vehicle equipped with a lane departure warning camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the lane departure warning camera may not be able to be installed due to a missing bracket or the lane departure alert system may not operate properly due to a difference in the transmissivity or black ceramic border.
56116C
1.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Using a brush or sponge, coat the application area of 2 new No. 2 windshield glass stoppers with Primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Install the 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.
| *A | Back Side | - | - |
| *1 | Ceramic Notch | - | - |
| *a | Windshield Glass Edge Side | - | - |
| Area | Dimension |
|---|---|
| a | 13.7 to 14.7 mm (0.539 to 0.578 in.) |
Only 2-piece type windshield glass stoppers are provided as supply parts. Use the 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
56115A
2.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
56114
3.INSTALL WINDSHIELD GLASS RETAINER
Using a brush or sponge, coat the application area of a new windshield outside moulding with Primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
| *A | Back Side |
| *1 | Ceramic Notch |
Install the 2 windshield glass retainers onto the windshield glass as shown in the illustration.
4.INSTALL WINDSHIELD OUTSIDE MOULDING
Using a brush or sponge, coat the application area of a new windshield outside moulding with Primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *A | Back Side |
Install the windshield outside moulding onto the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 6.7 mm (0.264 in.) |
56117A
5.INSTALL WINDSHIELD GLASS ADHESIVE DAM
Using a brush or sponge, coat the application area of a new windshield glass adhesive dam with Primer G.
| *A | Back Side | - | - |
| *1 | Primer G | *2 | Ceramic Notch |
| *3 | Label Area | - | - |
| Area | Dimension |
|---|---|
| a | 33.0 mm (1.30 in.) |
| b | 10.0 mm (0.394 in.) |
| c | 55.0 mm (2.17 in.) |
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
Keep label area clear of primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Install the windshield glass adhesive dam onto the windshield glass as shown in the illustration.
| *A | Back Side | - | - |
| *1 | Ceramic Notch | *2 | Windshield Glass Adhesive Dam |
| Area | Dimension |
|---|---|
| a | 36.0 mm (1.42 in.) |
56111
6.INSTALL WINDSHIELD GLASS SUB-ASSEMBLY
| *1 | Matchmark |
Position the windshield glass sub-assembly.
Using suction cups, place the windshield glass sub-assembly in the correct position.
Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.
Align the matchmarks on the windshield glass sub-assembly and vehicle body.
Check that the windshield glass stoppers are attached to the vehicle body correctly.
Remove the windshield glass sub-assembly.
Using a brush, coat the installation surface on the vehicle body with Primer M.
| *1 | Brush | *2 | Primer M |
| *3 | Adhesive | - | - |
| *a | CORRECT | *b | INCORRECT |
Do not coat the adhesive with Primer M.
Do not apply too much primer M.
Allow the primer M to dry for 3 minutes or more.
Throw away any leftover primer M.
If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.
Using a brush or sponge, coat the application area of adhesive with Primer G.
| *A | Back Side | - | - |
| *1 | Primer G | *2 | Ceramic Notch |
| *3 | Adhesive Center | - | - |
| Area | Dimension |
|---|---|
| a | 9.6 mm (0.378 in.) or more |
| b | 16.5 mm (0.650 in.) or more |
| c | 18.5 mm (0.728 in.) or more |
| d | 11.0 mm (0.433 in.) or more |
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
Apply Primer G onto the ceramic notches.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Apply adhesive to the glass.
Toyota Genuine Windshield Glass Adhesive or equivalent
| *1 | Nozzle |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 8.0 mm (0.315 in.) or more |
| b | 12.0 mm (0.472 in.) or more |
After cutting off the tip, use all adhesive within the time described in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the windshield glass sub-assembly as shown in the illustration.
| *A | Back Side | - | - |
| *1 | Adhesive | *2 | Ceramic Notch |
| *3 | Adhesive Center | - | - |
| Area | Dimension |
|---|---|
| a | 9.5 mm (0.374 in.) |
| b | 9.5 mm (0.374 in.) |
| c | 4.0 mm (0.157 in.) |
| d | 8.0 mm (0.315 in.) |
| e | 4.0 mm (0.157 in.) |
Apply adhesive onto the ceramic notches.
| *1 | Matchmark |
Install the windshield glass sub-assembly.
Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
Check that the windshield glass stoppers are attached to the vehicle body correctly.
Check the clearance between the vehicle body and windshield glass sub-assembly.
Lightly press the front surface of the windshield glass sub-assembly to ensure that the windshield glass is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Hold the windshield glass using protective tape until the applied adhesive becomes hard.
Do not drive the vehicle for the time described in the table below.
| Temperature | Minimum Time prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
7.INSPECT FOR LEAK AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
8.INSTALL ROOF HEADLINING ASSEMBLY
Return the front section of the roof headlining assembly to the original position.
63318C
9.INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
74348
10.INSTALL VISOR HOLDER
74320
11.INSTALL VISOR ASSEMBLY LH
74325
12.INSTALL VISOR BRACKET COVER (for LH Side)
74310
13.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74325
14.INSTALL VISOR BRACKET COVER (for RH Side)
Use the same procedure as for the LH side.
74630E
15.INSTALL REAR ASSIST GRIP ASSEMBLY LH
74620C
16.INSTALL REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure as for the LH side.
74610A
17.INSTALL ASSIST GRIP SUB-ASSEMBLY (for LH Side)
74610A
18.INSTALL ASSIST GRIP SUB-ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
81240
19.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)
81360T
20.INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)
63650A
21.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)
63650A
22.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)
62212
23.INSTALL FRONT PILLAR GARNISH LH
62312B
24.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62211
25.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62311B
26.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
86468
27.INSTALL LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)
89941
28.INSTALL RAIN SENSOR (w/ Rain Sensor)
87810
29.INSTALL INNER REAR VIEW MIRROR ASSEMBLY
55781E
30.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53867H
31.INSTALL FRONT FENDER TO COWL SIDE SEAL LH
53866J
32.INSTALL FRONT FENDER TO COWL SIDE SEAL RH
Use the same procedure as for the LH side.
33.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
34.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH