Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2015.04
RM2030EQ _58 Vehicle Interior _014674 INTERIOR PANELS / TRIM _0074669 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


PROCEDURE

Hide 1.INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

a.
B279105C20
2.26,1.552 2.677,1.844 0.417,0.292 10 false *b 1.292,0.885 1.646,1.188 0.354,0.302 10 false *a
*a Clip (Black)
*b Clip (White)


Install the 2 clips to the roof headlining assembly.


b.
B279011

Put the roof headlining assembly into the vehicle through the front passenger side door.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.



c.

Engage the 2 clips.

B396414C01
5.26,4.208 5.635,4.448 0.375,0.24 12 false *A
*A w/ Digital Audio Broadcasting Antenna - -



d.

Install the roof headlining assembly with the 2 clips.


e.

Engage the 4 clamps to the front pillar LH.


f.

Engage the 3 clamps to the front pillar RH.


g.

Connect the bracket with the bolt to the front pillar RH.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


h.

Engage the 2 clamps and connect the connector to the rear pillar RH.


i.

w/ Digital Audio Broadcasting Antenna:

i.

Engage the clamp and connect the connector to the rear pillar LH.



j.

w/ EC Mirror:

i.

Connect the connector to the inner rear view mirror.



k.

w/ Lane Departure Alert System:

i.

Connect the connector to the lane departure warning camera.


ii.

Connect the connector to the rain sensor.



Hide 2.INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

a.
B279105C20
2.26,1.552 2.677,1.844 0.417,0.292 10 false *b 1.292,0.885 1.646,1.188 0.354,0.302 10 false *a
*a Clip (Black)
*b Clip (White)


Install the 2 clips to the roof headlining assembly.


b.
B279012

Put the roof headlining assembly into the vehicle through the front passenger side door.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.



c.

Engage the 2 clips and 2 fasteners.

B396416C01
5.25,4.219 5.625,4.458 0.375,0.24 12 false *A
*A w/ Digital Audio Broadcasting Antenna - -



d.

Install the roof headlining assembly with the 2 clips.


e.

Engage the 4 clamps to the front pillar LH.


f.

Engage the 3 clamps to the front pillar RH.


g.

Connect the bracket with the bolt to the front pillar RH.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


h.

Engage the 2 clamps and connect the connector to the rear pillar RH.


i.

Connect the connector to the sliding roof drive gear assembly.


j.

w/ Digital Audio Broadcasting Antenna:

i.

Engage the clamp and connect the connector to the rear pillar LH.



k.

w/ EC Mirror:

i.

Connect the connector to the inner rear view mirror.



l.

w/ Lane Departure Alert System:

i.

Connect the connector to the lane departure warning camera.


ii.

Connect the connector to the rain sensor.



Hide 74348 3.INSTALL VISOR HOLDER

a.
B211698

Engage the 2 claws.


b.

Push in the visor holder as shown in the illustration.

HINT:

Use the same procedure for the other visor holder.



Hide 74320 4.INSTALL VISOR ASSEMBLY LH

a.

Install the visor assembly LH with the 2 screws.


Hide 74325 5.INSTALL VISOR BRACKET COVER (for LH Side)

a.
B278993

Engage the 4 claws to install the visor bracket cover.


Hide 74310 6.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74325 7.INSTALL VISOR BRACKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 63318C 8.INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

a.
B279103C10
1.052,2.896 0.99,2.719 false 0.531,2.354 0.354,2.313 false 0.188,2.208 0.469,2.438 0.281,0.229 10 false *a 1,2.917 1.26,3.094 0.26,0.177 10 false *b
*a Notch
*b Alignment Mark


Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.

NOTICE:

After installation, check that the corners fit correctly.



Hide 74610A 9.INSTALL ASSIST GRIP SUB-ASSEMBLY (for LH Side)

a.
B279001

Put the assist grip sub-assembly together as shown in the illustration.


b.
B279003

Engage the 2 clips to install the assist grip sub-assembly.


c.
B278996

Engage the 4 claws to install the 2 assist grip covers.


Hide 74610A 10.INSTALL ASSIST GRIP SUB-ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 74630E 11.INSTALL REAR ASSIST GRIP ASSEMBLY LH

a.
B279002

Put an rear assist grip assembly LH together as shown in the illustration.


b.
B279004

Engage the 2 clips to install the rear assist grip assembly LH.


c.
B278998

Engage the 4 claws to install the 2 assist grip covers.


Hide 74620C 12.INSTALL REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 81240 13.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)

Hide 81360T 14.INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)

Hide 63650A 15.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)

Hide 63650A 16.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)

Hide 86466 17.INSTALL NO. 1 LANE DEPARTURE WARNING CAMERA COVER (w/ Lane Departure Alert System)

Hide 86466C 18.INSTALL NO. 2 LANE DEPARTURE WARNING CAMERA COVER (w/ Lane Departure Alert System)

Hide 89943 19.INSTALL RAIN SENSOR COVER (w/ Lane Departure Alert System)

Hide 87834 20.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

w/o Lane Departure Alert System: Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR>INSTALLATION

Hide 23.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62472A 24.INSTALL ROOF SIDE INNER GARNISH LH

a.

Engage the guide.


b.

Engage the 5 clips to install the roof side inner garnish LH.


Hide 62412B 25.INSTALL CENTER PILLAR UPPER GARNISH LH

a.

Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH.


b.

Engage the clip.


c.

Install the center pillar upper garnish LH with the 2 screws.


Hide 62414A 26.INSTALL CENTER PILLAR LOWER GARNISH LH

a.

Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.


Hide 73220 27.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73233 28.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 62332A 29.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B334263C15
1.948,3.604 2.042,3.365 2.042,3.365 2.167,3.365 false 2.188,3.25 2.5,3.448 0.313,0.198 10 false *a
*a Alignment Mark (Red)


Align the alignment mark (Red) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

NOTICE:

After installation, check that the corners fit correctly.



Hide 67918A 30.INSTALL REAR DOOR SCUFF PLATE LH

a.

Engage the 6 claws to install the rear door scuff plate LH.

HINT:

Engage the claws from the rear side of the scuff plate.



Hide 62471A 31.INSTALL ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62411B 32.INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 33.INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73210 34.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 35.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 62331A 36.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.
B334264C13
1.458,3.594 1.385,3.313 1.385,3.313 1.198,3.313 false 1.052,3.198 1.365,3.396 0.313,0.198 10 false *a
*a Alignment Mark (Blue)


Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

NOTICE:

After installation, check that the corners fit correctly.



Hide 67917A 37.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 38.INSTALL REAR SEATBACK ASSEMBLY LH

Hide 39.INSTALL REAR SEATBACK ASSEMBLY RH

Hide 40.INSTALL REAR SIDE SEATBACK ASSEMBLY LH

Hide 41.INSTALL REAR SIDE SEATBACK ASSEMBLY RH

Hide 72693 42.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 43.INSTALL REAR SEAT CUSHION ASSEMBLY

Hide 62212 44.INSTALL FRONT PILLAR GARNISH LH

a.

Remove the protective cover.


b.

Make sure that the front pillar garnish clip is not damaged.

NOTICE:

If the front pillar garnish clip is damaged, replace the front pillar garnish clip with a new one.



c.
B278987

Install the front pillar garnish clip to front pillar garnish LH.

HINT:

Install the front pillar garnish clip so that it faces as shown in the illustration.

B453135C01
0.917,0.167 1.229,0.365 0.313,0.198 10 false *a 3,0.167 3.313,0.365 0.313,0.198 10 false *b 5.083,0.167 5.396,0.365 0.313,0.198 10 false *b
*a Correct *b Incorrect




d.

Engage the 2 guides as shown in the illustration.


e.
B278984

Engage the front pillar garnish clip and clip to install the front pillar garnish LH.

HINT:

Make sure that the curtain shield airbag assembly LH is not pinched.



Hide 62312B 45.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B334260C13
1.948,3.615 2.01,3.344 2.01,3.344 2.167,3.344 false 2.188,3.229 2.5,3.427 0.313,0.198 10 false *a
*a Alignment Mark (Yellow)


Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

NOTICE:

After installation, check that the corners fit correctly.



Hide 62112A 46.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

a.
B294701

Insert the 2 clips as shown in the illustration to engage them.


b.

Install the cowl side trim sub-assembly LH with the clip.


Hide 67914 47.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Engage the 10 claws to install the front door scuff plate LH.


Hide 62211 48.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 49.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B334262C13
1.094,3.24 1.344,3.24 1.344,3.24 1.458,3.604 false 0.938,3.156 1.25,3.354 0.313,0.198 10 false *a
*a Alignment Mark (White)


Align the alignment mark (White) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

NOTICE:

After installation, check that the corners fit correctly.



Hide 62111A 50.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 67913 51.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 52.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION