Perform "Inspection After Repair" after replacing the camshaft, No. 2 camshaft or camshaft timing gear assembly.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
13050
1.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
11821
2.INSTALL NO. 2 CAMSHAFT BEARING
11811
3.INSTALL NO. 1 CAMSHAFT BEARING
15678A
4.INSTALL OIL CONTROL VALVE FILTER
13523
5.INSTALL CAMSHAFT TIMING SPROCKET
Secure the camshaft in a vice by clamping the hexagonal part using aluminum plates.
Do not damage the camshaft by tightening the vice excessively.
Install the camshaft timing sprocket to the No. 2 camshaft with the bolt.
Do not damage the No. 2 camshaft or camshaft timing sprocket.
6.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *a | Timing Notch |
Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover are aligned.
13512
7.INSTALL NO. 2 CAMSHAFT
Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.
| *A | Type A | *B | Type B |
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Lash Adjuster Assembly |
| *3 | Valve Stem Cap | - | - |
Clean the camshaft journals.
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.
| *a | Paint Mark |
| *b | Timing mark |
Hold up the chain and align the timing mark and the paint mark, and install the No. 2 camshaft.
Perform "Inspection After Repair" after replacing the No. 2 camshaft.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
13511
8.INSTALL CAMSHAFT
Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.
| *A | Type A | *B | Type B |
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Lash Adjuster Assembly |
| *3 | Valve Stem Cap | - | - |
Clean the camshaft journals.
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.
| *1 | Knock Pin |
| *a | Approximately 17° |
Install the camshaft to the camshaft housing as shown in the illustration.
Perform "Inspection After Repair" after replacing the camshaft.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
9.INSTALL CAMSHAFT BEARING CAP
Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.
Using several steps, uniformly tighten the 10 bolts in the sequence shown in the illustration.
Using several steps, uniformly tighten the 11 bolts in the sequence shown in the illustration.
Check the torque of each bolt again.
13050
10.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
| *1 | Knock Pin Hole |
| *a | Advanced Position |
| *b | Retarded Position |
| *c | Alignment Mark |
Check the camshaft timing gear position.
If the camshaft timing gear is set to the advanced position, do not let the camshaft timing gear rotate clockwise during installation.
If the camshaft timing gear has rotated to the most retarded position, make sure to release the lock pin and set the camshaft timing gear to the most advanced position before tightening the camshaft timing gear.
| *a | Narrow |
| *b | Wide |
Install the camshaft timing gear as shown in the illustration.
| *a | Narrow |
| *b | Wide |
Turn the camshaft timing gear approximately 180° counterclockwise.
| *a | Paint Mark |
| *b | Timing mark |
Align the paint mark with the timing mark to install the chain.
| *1 | Knock Pin |
| *a | Knock Pin Hole |
Align and attach the knock pin of the camshaft with the pin hole of the camshaft timing gear.
| *1 | Camshaft Timing Gear |
| *a | Camshaft Flange |
| *b | No Clearance |
Check that there is no clearance between the camshaft timing gear and camshaft flange.
Secure the camshaft in place by hand, and then install the installation bolt of the camshaft timing gear by hand.
Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.
If the lock pin has not been released, release it.
| *a | Make a Hole |
| *b | Adhesive Tape Sealing Area |
After cleaning and degreasing the intake side VVT oil hole on the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.
Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.
Make a hole in the adhesive tape covering the oil hole as shown in the illustration. (Procedure A)
Apply approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the hole made in procedure A to release the lock pin.
If air leaks out, reattach the adhesive tape.
Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.
Forcibly turn the camshaft timing gear in the advance direction (counterclockwise).
Depending on the air pressure applied, the camshaft timing gear may turn in the advance direction without assistance by hand.
Remove the adhesive tape from the No. 1 camshaft bearing cap.
| *a | Hold |
| *b | Turn |
Using a wrench to hold the hexagonal portion of the camshaft, install the bolt.
Be careful not to damage the cylinder head or spark plug tube with the wrench.
| *a | Paint Mark |
| *b | Timing Mark |
Check that each timing mark of the camshaft timing gear and camshaft timing sprocket are aligned with each timing mark located as shown in the illustration.
Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
11.ADD ENGINE OIL
13566B
12.INSTALL TIMING CHAIN GUIDE
13540
13.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Turn the crankshaft approximately 10° clockwise.
Install a new gasket and the No. 1 chain tensioner assembly with the 2 bolts.
Make sure not to drop the gasket inside the timing chain cover.
Remove the pin from the stopper plate.
14.SET NO. 1 CYLINDER TO TDC/COMPRESSION
Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover are aligned.
| *a | Approximately 7° | *b | Approximately 32° |
| *c | Timing Mark | *d | Timing Notch |
Check that the timing marks of the camshaft timing gears are as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.
"A" is not a timing mark.
11324
15.INSTALL TIMING CHAIN COVER PLATE
Install a new gasket and the timing chain cover plate with the 4 bolts.
16.INSTALL OIL PUMP RELIEF VALVE PLUG
11201
17.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
19500
18.INSTALL IGNITION COIL ASSEMBLY
82121
19.CONNECT ENGINE WIRE
Install the engine wire to the engine with the 5 bolts and 3 nuts.
| *1 | Nut | - | - |
Connect the 8 connectors and 2 harness clamps.
12309
20.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY
82284
21.CONNECT EARTH WIRE
12327A
22.INSTALL NO. 2 ENGINE MOUNTING STAY RH
17701
23.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
24.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17735
25.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
17750A
26.INSTALL INLET AIR CLEANER ASSEMBLY
27.INSPECT FOR OIL LEAK
53736
28.INSTALL FRONT FENDER APRON SEAL RH
51441C
29.INSTALL ENGINE UNDER COVER RH
53851Z
30.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH
12601B
31.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
53295E
32.INSTALL COOL AIR INTAKE DUCT SEAL
33.INSTALL FRONT WHEEL RH