Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE UNIT
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074906 ENGINE UNIT A

2AR-FXE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.
A198197C07
2.374,2.431 2.555,2.586 0.181,0.155 10 *a
*a Protrusion Height


Using a plastic-faced hammer, tap in 2 ring pins until they stop.

Standard protrusion height:

4.3 to 5.3 mm (0.169 to 0.209 in.)



Hide 13620B 2.INSTALL ENGINE BALANCER ASSEMBLY

a.
A198170C09
2.188,0.99 1.521,0.698 1.521,0.698 2.188,1.104 true 1.729,1.333 1.063,1.333 true 1.104,0.885 1.188,0.885 1.188,0.885 1.583,1.063 true 1.323,0.615 1.479,0.76 0.156,0.146 10 true *a 0.833,1.24 0.99,1.385 0.156,0.146 10 true *2 0.927,0.792 1.083,0.938 0.156,0.146 10 true *1
*1 Driven Gear
*2 Damper Cover
*a Alignment Mark


Check that the alignment marks of the balance shaft damper cover and balance shaft driven gear are aligned.

If the alignment marks are not aligned, realign them.

i.
A198171C08
1.177,0.917 1.313,0.917 1.313,0.917 1.563,1.198 true 2.208,1.281 2.635,1.583 2.635,1.583 2.292,1.156 true 1.156,1.688 1.302,1.688 1.302,1.688 1.667,1.552 true 0.969,0.823 1.167,0.979 0.198,0.156 10 true *1 0.958,1.635 1.146,1.813 0.188,0.177 10 false *2 2.677,1.594 2.875,1.771 0.198,0.177 10 true *a
*1 Driven Gear
*2 Damper Cover
*a Alignment Mark


Place a wrench on the rear cutout part of the No. 2 balance shaft and secure the shaft in place.


ii.

Rotate the balance shaft driven gear of the No. 1 balance shaft counterclockwise to align the alignment mark of the balance shaft driven gear with the alignment mark of the balance shaft damper cover.



b.
A196927N07
0.927,1.406 1.094,1.573 0.167,0.167 10 true 1 2.615,0.188 2.729,0.365 0.115,0.177 10 true 2 2.719,1.688 2.844,1.833 0.125,0.146 10 true 3

Install the engine balancer assembly to the stiffening crankcase with the 3 bolts, and tighten the bolts in the sequence shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 3.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


a.

Using an E5 and E8 "TORX" socket wrench, install the 3 stud bolts.

A198166C06
5.063,0.385 4.76,0.74 false 5.146,1.802 4.76,2.083 false 5.104,1.417 4.76,1.146 false 5.156,2.615 4.76,2.375 false 5.198,1.719 6.427,1.917 1.229,0.198 10 false 8.5 mm (0.335 in.) 5.229,2.563 6.49,2.771 1.26,0.208 10 false 8.0 mm (0.315 in.) 5.385,2.167 6.583,2.354 1.198,0.188 10 false 18 mm (0.709 in.) 2.26,1.063 2.375,1.219 0.115,0.156 10 false A 4.146,0.115 4.26,0.271 0.115,0.156 10 false A 1.063,1.875 1.208,2.021 0.146,0.146 10 false B 1.625,2.271 1.729,2.427 0.104,0.156 10 true B 4.156,1.646 4.302,1.792 0.146,0.146 10 false B 5.135,1.344 6.281,1.573 1.146,0.229 10 false 13 mm (0.512 in.) 5.115,0.26 6.26,0.5 1.146,0.24 10 false 20 mm (0.787 in.) 5.365,0.813 6.531,1.021 1.167,0.208 10 false 35 mm (1.38 in.) 0.208,0 0.396,0.167 0.188,0.167 10 false *a 0.208,1.302 0.396,1.49 0.188,0.188 10 false *b
*a Front Side *b Lower Side


Torque:
for Stud Bolt A : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
for Stud Bolt B : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 11420 4.INSTALL STIFFENING CRANKCASE ASSEMBLY

a.
A198168C06
0.771,0.646 1.5,1.052 true 0.583,0.552 0.75,0.74 0.167,0.188 10 false *a 1.188,1.563 1.427,1.729 0.24,0.167 10 true 90°
*a Key


Rotate the crankshaft clockwise so that the crankshaft key is at the position 90° from the bottom as shown in the illustration.


b.
A260216C02
1.885,0.094 2.031,0.094 2.031,0.094 2.281,0.698 false 0.979,0.031 2.281,0.521 1.302,0.49 10 false 2.5 to 3.5 mm 2.438,0.042 3.167,0.354 0.729,0.313 10 false 28 mm 2.083,2.469 3.313,2.885 1.229,0.417 10 false 7.0 to 9.0 mm 2.99,0.292 3.26,0.563 0.271,0.271 10 false A 1.344,2.302 1.656,2.615 0.313,0.313 10 false A 0.292,2.885 1.635,3.26 1.344,0.375 10 false 2.5 to 3.5 mm
V100144

Stiffening Crankcase
V100146

Cylinder Block


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Dimension:
Area Specified Condition
Continuous Line 2.5 to 3.5 mm (0.0984 to 0.138 in.)
Dashed Line 7.0 to 9.0 mm (0.276 to 0.354 in.) wide and 2.5 to 3.5 mm (0.0984 to 0.138 in.) thick


Application Length A:

28 mm (1.10 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes after applying seal packing.

·

Do not apply oil for at least 2 hours after the installation.




c.
A285537C04
1.417,0.979 1.208,0.302 1.208,0.302 1.99,0.99 false 1.083,0.125 1.396,0.281 0.313,0.156 10 *a
*a Cutout


Check that the rear cutout parts are as shown in the illustration.


d.

Clean the bolts and their installation holes.


e.
A198186C07
1.545,0.47 1.708,0.647 0.163,0.177 10 *1 1.742,0.557 2.086,0.832 false
*1 Adhesive


Apply adhesive to 3 or more threads of the ends of bolts A.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.
A198172N02
0.698,0.25 0.813,0.406 0.115,0.156 10 false A 0.948,1.948 1.063,2.104 0.115,0.156 10 false A 2.719,0.031 2.865,0.177 0.146,0.146 10 false B 2.948,1.844 3.094,1.99 0.146,0.146 10 false B 2.865,0.844 3.01,0.99 0.146,0.146 10 true C 2.573,1.927 2.719,2.073 0.146,0.146 10 false C 2.854,1.083 2.979,1.219 0.125,0.135 10 true C 2.313,0.052 2.458,0.208 0.146,0.156 10 false D 2.198,1.031 2.323,1.188 0.125,0.156 10 true D 1.531,2.021 1.646,2.177 0.115,0.156 10 true D 1.49,0 1.625,0.146 0.135,0.146 10 true D

Temporarily install the stiffening crankcase with the 11 bolts.

Bolt Length :
Item Length
Bolt A 65 mm (2.56 in.)
Bolt B 35 mm (1.38 in.)
Bolt C 125 mm (4.92 in.)
Bolt D 165 mm (6.50 in.)


HINT:

Apply adhesive to bolts A before installation.



g.
A198172N03
2.833,1.073 2.938,1.219 0.104,0.146 10 true 9 2.542,1.948 2.635,2.104 0.094,0.156 10 false 1 2.333,0.042 2.458,0.219 0.125,0.177 10 false 2 2.208,1.031 2.323,1.177 0.115,0.146 10 true 3 2.719,0.042 2.813,0.198 0.094,0.156 10 false 4 2.969,1.854 3.083,2 0.115,0.146 10 false 5 1.542,0.021 1.656,0.177 0.115,0.156 10 true 6 1.531,2.021 1.656,2.167 0.125,0.146 10 true 7 2.833,0.875 2.927,1.021 0.094,0.146 10 true 8 0.604,0.25 0.781,0.396 0.177,0.146 10 false 10 0.865,1.938 1.042,2.083 0.177,0.146 10 false 11

Tighten the 11 bolts in the sequence shown in the illustration to install the stiffening crankcase

Torque:
for Bolt A : 24 N*m (245 kgf*cm, 18 ft.*lbf)
except Bolt A : 43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 12121 5.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.
A196920N02
1.135,0.563 1.26,0.708 0.125,0.146 10 true 1 2.083,1.948 2.177,2.125 0.094,0.177 10 false 2 0.635,0.844 0.75,0.99 0.115,0.146 10 true 3 1.479,1.948 1.604,2.104 0.125,0.156 10 true 4 1.219,0.188 1.333,0.344 0.115,0.156 10 true 5

Install the No. 1 oil pan baffle plate and uniformly tighten the 5 bolts in several steps, in the sequence shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new gasket.


b.
A198187C02
1.635,0.365 2.115,0.625 false 1.417,0.25 1.594,0.438 0.177,0.188 10 false *a 0.573,1.927 0.708,2.083 0.135,0.156 10 true 1 0.646,3.052 0.74,3.229 0.094,0.177 10 true 2 2.146,2.99 2.26,3.135 0.115,0.146 10 true 3
*a Protrusion


Align the protrusion of the gasket with the cutout of the oil strainer, and install the gasket to the oil strainer sub-assembly.


c.

Install the oil strainer sub-assembly with the 3 bolts in several steps, in the sequence shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 12101 7.INSTALL OIL PAN SUB-ASSEMBLY

a.
A210205N05
1.5,1.656 1.844,1.656 false 0.563,1.583 1.552,1.75 0.99,0.167 10 false 2.5 to 3.5 mm

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.

·

Do not apply oil for at least 2 hours after the installation.




b.
A210204C09
0.76,1.208 1.771,1.427 1.771,1.427 1.49,1.823 false 1.833,1.354 2.01,1.5 0.177,0.146 10 false *1 2.042,0 2.313,0.156 0.271,0.156 10 false 1, 9 1.104,2 1.469,2.156 0.365,0.156 10 false 2, 15 0.823,1.938 0.938,2.083 0.115,0.146 10 false 3 0.427,1.625 0.521,1.781 0.094,0.156 10 false 4 0.385,1.01 0.5,1.156 0.115,0.146 10 false 5 0.708,0.708 0.823,0.865 0.115,0.156 10 false 6 0.99,0.5 1.083,0.635 0.094,0.135 10 true 7 1.146,0.063 1.24,0.208 0.094,0.146 10 false 8 2.313,0.292 2.49,0.438 0.177,0.146 10 false 10 2,2 2.177,2.146 0.177,0.146 10 false 14 2.458,1.76 2.635,1.906 0.177,0.146 10 false 13 2.583,1.146 2.76,1.292 0.177,0.146 10 true 12 2.583,0.729 2.76,0.875 0.177,0.146 10 true 11 1.583,1.833 1.698,1.99 0.115,0.156 10 true A 1.688,0.083 1.833,0.229 0.146,0.146 10 false A
*1 Nut


Install the oil pan with the 11 bolts and 2 nuts in several steps, in the sequence shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Bolt A and nut A are tightened twice.



Hide 12101A 8.INSTALL OIL PAN DRAIN PLUG

a.

Install a new gasket and oil pan drain plug to the oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15620 9.INSTALL OIL FILTER CAP ASSEMBLY

Hide 11445 11.INSTALL CYLINDER BLOCK WATER JACKET SPACER

a.
A196938

Install the cylinder block water jacket spacer to the cylinder block.


Hide 11101 13.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 11151A 14.INSTALL CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.
A198195C09
2.422,1.604 2.595,1.757 0.172,0.152 10 *a
*a Protrusion Height


Using a plastic-faced hammer, tap in 10 camshaft bearing cap setting ring pins to the camshaft housing sub-assembly.

Standard protrusion height:

2.7 to 3.3 mm (0.106 to 0.130 in.)



Hide 11114A 15.INSTALL STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.


a.
A198194C07
2.109,1.583 2.27,1.739 0.162,0.156 10 *a
*a Protrusion Height


Using a plastic-faced hammer, tap in 2 straight pins to the camshaft housing sub-assembly.

Standard protrusion height:

5.0 to 7.0 mm (0.197 to 0.276 in.)



Hide 16.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


a.

When reusing the stud bolt.

i.

Apply adhesive to threads of the stud bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent




b.
A198196N07
1.875,1.688 1.75,1.688 1.75,1.688 1.531,2.271 false 1.531,2.802 1.896,3.25 1.896,3.25 2.125,3.25 false 2.167,3.167 3.313,3.396 1.146,0.229 10 false 13 mm (0.512 in.) 1.948,1.594 3.094,1.833 1.146,0.24 10 false 20 mm (0.787 in.) 2.25,2.375 3.375,2.573 1.125,0.198 10 false 35 mm (1.38 in.)

Using an E8 "TORX" socket wrench, install the camshaft housing stud bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 11811 17.INSTALL NO. 1 CAMSHAFT BEARING

a.

Clean the No. 1 camshaft bearing.


b.
A243410C03
2.333,2.583 2.01,2.583 2.01,2.583 1.802,2.271 false 2.365,2.5 2.719,2.75 0.354,0.25 10 false *1 0.125,2.375 0.448,2.75 0.323,0.375 10 false A 1.635,2.375 2.01,2.802 0.375,0.427 10 false B
*1 Vernier Caliper


Install the No. 1 camshaft bearing to the No. 1 camshaft bearing cap.


c.

Using a vernier caliper, measure the distance between the No. 1 camshaft bearing cap edge and the No. 1 camshaft bearing edge.

Standard dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



Hide 11821 18.INSTALL NO. 2 CAMSHAFT BEARING

a.

Clean the No. 2 camshaft bearing.


b.
A198177C11
0.917,1.313 0.823,1.313 0.823,1.313 0.74,2.531 false 0.854,2.333 0.99,2.5 0.135,0.167 10 false A 0.979,1.198 1.167,1.385 0.188,0.188 10 false *1
*1 Vernier Caliper


Install the No. 2 camshaft bearing to the camshaft housing sub-assembly.


c.

Using a vernier caliper, measure the distance between the camshaft housing edge and the No. 2 camshaft bearing edge.

Standard distance:

1.15 to 1.85 mm (0.0453 to 0.0728 in.)



Hide 15678A 19.INSTALL OIL CONTROL VALVE FILTER

a.
A196915

Install the oil control valve filter to the No. 1 camshaft bearing cap.


Hide 13750 23.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 24.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11103 25.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13050 27.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13521 28.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A196881

Install the crankshaft timing sprocket to the crankshaft.


Hide 13561 30.INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 13540 34.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11324 37.INSTALL TIMING CHAIN COVER PLATE

a.
A196860

Install a new gasket and the timing chain cover plate with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 38.INSTALL OIL PUMP RELIEF VALVE PLUG

a.
A196859

Using a 14 mm hexagon wrench, install a new gasket and the oil pump relief valve plug.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 11302 39.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 12315A 40.INSTALL ENGINE MOUNTING BRACKET RH

Hide 11301C 41.INSTALL TIMING CHAIN COVER OIL SEAL

Hide 11193 42.INSTALL SPARK PLUG TUBE GASKET

a.
A259162C02
1.031,2.76 0.833,2.958 0.833,2.958 0.635,2.958 false 1.135,2.521 1.031,2.073 1.031,2.073 0.917,2.073 false 0.708,2.01 0.885,2.198 0.177,0.188 10 false *1 0.448,2.885 0.625,3.073 0.177,0.188 10 false *2
*1 Spark Plug Tube Gasket
*2 Cylinder Head Cover Sub-assembly


Tap in the 4 new spark plug tube gaskets to the cylinder head cover sub-assembly.

NOTICE:
·

Do not allow foreign matter to contact the lip of the spark plug tube gasket.

·

Do not tap in the spark plug tube gasket at an angle.




Hide 43.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A260355N02
1.125,2.563 1.5,1.813 1.5,1.813 1.719,1.813 false 1.542,2.74 1.885,2.74 false 1.125,2.969 1.573,2.177 1.573,2.177 1.719,2.177 false 1.75,1.729 3.219,1.99 1.469,0.26 10 false 16 mm (0.63 in.) 1.927,2.656 3.333,3.021 1.406,0.365 10 false 27 mm (1.06 in.) 1.76,2.104 3.24,2.406 1.479,0.302 10 false 9 mm (0.354 in.)

Using an E6 "TORX" socket wrench, install the 3 stud bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 11201 44.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A259133

Apply a light coat of engine oil to 2 new gaskets.


b.

Install the 2 gaskets to the camshaft bearing caps.


c.

Install a new gasket to the cylinder head cover sub-assembly.

NOTICE:

Remove any oil from the contact surface.



d.
A259161C05
2.458,2.479 2.281,2.479 2.281,2.479 2.167,2.833 false 1.042,2.479 1.177,2.479 1.177,2.479 1.281,2.833 false 1.948,2.146 1.823,2.146 1.823,2.146 1.688,2.615 false 1.99,2.073 2.219,2.26 0.229,0.188 10 false *1 0.854,2.396 1.156,2.615 0.302,0.219 10 false *2 2.5,2.406 2.896,2.677 0.396,0.271 10 false *3 1.5,3.063 1.646,3.229 0.146,0.167 10 false A 1.802,3.063 1.948,3.229 0.146,0.167 10 false A 0.781,0.135 1.01,0.323 0.229,0.188 10 false *1 0.75,2.167 0.979,2.354 0.229,0.188 10 false *1
*1 Seal Packing
*2 Timing Chain Cover
*3 Camshaft Housing


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)


Application width A:

5.0 mm (0.197 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes after applying seal packing.




e.
A283980C04
0.51,0.115 0.646,0.115 0.646,0.115 0.719,0.344 false 3.208,1.458 3.313,1.552 3.313,1.552 3.313,1.656 false 1.417,1.083 2.271,1.479 2.271,1.479 2.792,1.219 false 2.26,1.479 2.302,1.208 false 0.354,0 0.667,0.156 0.313,0.156 10 false *a 3.24,1.677 3.427,1.865 0.188,0.188 10 false *b 2.177,1.5 2.365,1.667 0.188,0.167 10 true *1 2.115,0.792 2.594,0.99 0.479,0.198 10 false 1, 19 1.354,0.688 1.833,0.885 0.479,0.198 10 false 2, 20 2.615,0.792 3.094,0.99 0.479,0.198 10 false 3, 21 1.813,0.156 2.302,0.365 0.49,0.208 10 false 4, 12 1.615,1.979 2.094,2.177 0.479,0.198 10 false 5, 18 1.198,1.969 1.375,2.146 0.177,0.177 10 false 6 0.302,1.927 0.479,2.104 0.177,0.177 10 false 7 0.094,1.313 0.271,1.49 0.177,0.177 10 false 8 0.302,0.208 0.469,0.396 0.167,0.188 10 false 9 0.781,0.063 0.948,0.25 0.167,0.188 10 false 10 1.375,0.156 1.542,0.344 0.167,0.188 10 false 11 2.344,0.167 2.51,0.354 0.167,0.188 10 false 13 2.969,0.219 3.156,0.417 0.188,0.198 10 false 14 2.948,1.854 3.115,2.042 0.167,0.188 10 false 16 3.219,0.802 3.385,0.99 0.167,0.188 10 false 15 2.281,1.958 2.448,2.146 0.167,0.188 10 false 17
*1 Seal Washer
*a Pin A
*b Pin B


Align the cylinder head cover with pin A. Then align the cylinder head cover with pin B and install the cylinder head cover sub-assembly.


f.

Install 3 new seal washers and the 16 bolts, and then tighten the bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not apply oil for at least 2 hours after the installation.



Hide 13471 45.INSTALL CRANKSHAFT PULLEY

a.
A305738C02
1.313,0.927 0.875,0.875 0.875,0.875 1.198,0.635 true 0.833,0.208 1.146,0.365 0.313,0.156 10 false *a 2.26,1.688 2.573,1.844 0.313,0.156 10 false *b 0.542,0.802 1,1 0.458,0.198 10 false SST
*a Hold
*b Turn


Align the pulley set key with the key groove of the crankshaft pulley.


b.

Using SST, hold the crankshaft pulley and install the pulley bolt.

SST
09213-54015  
09330-00021  

Torque:
260 N*m (2651 kgf*cm, 192 ft.*lbf)

HINT:

SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)



Hide 11301K 46.INSTALL CRANKSHAFT POSITION SENSOR

Hide 12215 47.INSTALL SEPARATOR CASE

a.
A210188

Apply a light coat of engine oil to a new gasket.


b.

Install the gasket to the separator case.


c.

Install the separator case with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12205 48.INSTALL VENTILATION CASE SUB-ASSEMBLY

a.
A210187N06
1.394,1.795 2.298,1.951 0.903,0.156 10 2.5 to 3.5 mm 1.364,1.887 1.248,1.887 1.248,1.887 1.035,1.603 false

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the ventilation case within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A210185N02
0.49,1.323 0.583,1.323 0.583,1.323 0.792,1.427 true 2.719,0.573 2.531,0.573 true 0.896,0 1.094,0.167 0.198,0.167 10 false 10 1.542,0.031 1.719,0.198 0.177,0.167 10 true 11 2.813,0.094 3.135,0.25 0.323,0.156 10 true 2, 12 0.198,1.708 0.469,1.875 0.271,0.167 10 true 1, 8 3.052,0.906 3.156,1.073 0.104,0.167 10 true 3 2.938,1.708 3.052,1.896 0.115,0.188 10 true 4 1.917,1.927 2.021,2.094 0.104,0.167 10 true 5 0.365,0.281 0.563,0.458 0.198,0.177 10 true 9 1.021,1.667 1.125,1.833 0.104,0.167 10 true 7 1.271,1.927 1.375,2.094 0.104,0.167 10 true 6 2.76,0.49 2.885,0.656 0.125,0.167 10 true A 0.365,1.25 0.49,1.417 0.125,0.167 10 true A

Install the ventilation case sub-assembly, and install the 8 bolts and 2 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Do not apply oil for at least 2 hours after the installation.


HINT:

Bolt A is tightened twice.



Hide 12204 49.INSTALL VENTILATION VALVE SUB-ASSEMBLY

Hide 11101J 51.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 12108A 52.INSTALL OIL FILLER CAP GASKET

a.

Install a new oil filler cap gasket to the oil filler cap sub-assembly.


Hide 12108 53.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.


Hide 83530 54.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 55.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 89615 56.INSTALL KNOCK CONTROL SENSOR

Hide 58.INSTALL ENGINE COVER JOINT

a.
A259127

Install the 3 engine cover joints.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)