Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › CAMSHAFT
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074901 CAMSHAFT A

2AR-FXE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL RH

Hide 53851Z 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441C 3.REMOVE ENGINE UNDER COVER RH

Hide 53736 4.REMOVE FRONT FENDER APRON SEAL RH

Hide 12601B 5.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53295E 6.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 7.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17735 8.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 9.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 10.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 12327A 11.REMOVE NO. 2 ENGINE MOUNTING STAY RH

Hide 12309 13.REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

Hide 82121 14.DISCONNECT ENGINE WIRE

a.

Disconnect the 8 connectors and 2 harness clamps.

A260217


b.

Remove the 5 bolts and 3 nuts and disconnect the engine wire from the engine.


Hide 11201 16.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 17.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A259740C02
0.948,0.927 1.76,0.313 1.76,0.313 2.74,0.958 true 1.844,3.25 2.177,3.094 true 0.885,1.208 1.76,1.573 1.76,1.573 2.719,1.073 true 1.688,0.094 1.906,0.302 0.219,0.208 10 true *a 1.688,1.594 1.906,1.833 0.219,0.24 10 true *b 2.208,2.99 2.479,3.281 0.271,0.292 10 true *c
*a Paint Mark
*b Timing Mark
*c Timing Notch


Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover are aligned.


b.

Check that each timing mark of the camshaft timing gear assembly and camshaft timing sprocket are aligned with each timing mark located as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.


c.

Place paint marks on the chain in alignment with the timing marks on the camshaft timing gear and camshaft timing sprocket.


Hide 11324 18.REMOVE TIMING CHAIN COVER PLATE

a.
A259741

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 13540 19.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A259742N05
1.958,0.052 2.198,0.208 0.24,0.156 10 true 10°

Turn the crankshaft approximately 10° clockwise.


b.
A259743N03
1.948,0.021 2.177,0.177 0.229,0.156 10 true 10°

Turn the crankshaft approximately 10° counterclockwise.


c.
A249932C10
1.906,1.896 1.615,1.708 true 1.948,1.833 2.177,1.979 0.229,0.146 10 true *1
*1 Pin


Align the holes of the stopper plate and tensioner, and insert a pin into the stopper plate hole to lock the tensioner.


d.
A259742N05
1.958,0.052 2.198,0.208 0.24,0.156 10 true 10°

Turn the crankshaft approximately 10° clockwise.


e.
A249933

Remove the 2 bolts, chain tensioner and gasket.

NOTICE:

Make sure not to drop the gasket inside the timing chain cover.



f.
A259743N03
1.948,0.021 2.177,0.177 0.229,0.156 10 true 10°

Turn the crankshaft approximately 10° counterclockwise.


Hide 21.REMOVE OIL PUMP RELIEF VALVE PLUG

Hide 13050 22.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A259765C02
2.17,0.498 2.322,0.652 0.152,0.154 10 *a 0.466,0.889 0.618,1.043 0.152,0.154 10 *b
*a Hold
*b Turn


Hold the hexagonal portion of the camshaft with a wrench and remove the bolt from the camshaft.

NOTICE:

Be careful not to damage the cylinder head or spark plug tube with the wrench.



b.
A259766

Separate the camshaft timing gear assembly from the camshaft.


c.
A259767C02
2.702,1.995 2.854,2.149 0.152,0.154 10 *a 2.768,2.988 2.92,3.142 0.152,0.154 10 *b 1.24,1.995 1.392,2.149 0.152,0.154 10 *b 1.181,2.988 1.333,3.142 0.152,0.154 10 *a
*a Narrow
*b Wide


Remove the timing chain from the camshaft timing gear assembly, and turn the camshaft timing gear assembly approximately 180°.


d.
A259739

Remove the camshaft timing gear assembly.

NOTICE:

Do not disassemble the camshaft timing gear.



Hide 23.REMOVE CAMSHAFT BEARING CAP

a.
A259738N03
1.177,0.021 1.448,0.208 0.271,0.188 10 true 6 1.688,0.021 1.948,0.229 0.26,0.208 10 true 10 2.292,0.031 2.385,0.188 0.094,0.156 10 true 8 2.833,0.031 2.927,0.188 0.094,0.156 10 true 4 0.729,0.052 0.99,0.25 0.26,0.198 10 true 2 0.552,1.802 0.76,1.99 0.208,0.188 10 true 1 1.135,1.542 1.344,1.781 0.208,0.24 10 true 7 2.333,1.542 2.542,1.792 0.208,0.25 10 true 9 2.938,1.542 3.135,1.813 0.198,0.271 10 true 5 1.688,1.542 1.927,1.781 0.24,0.24 10 true 11 0.156,1.135 0.292,1.323 0.135,0.188 10 true 3

Using several steps, remove the 11 bearing cap bolts in the sequence shown in the illustration.


b.
A259759N03
1.677,0.333 1.906,0.5 0.229,0.167 10 true 10 0.552,1.906 0.646,2.063 0.094,0.156 10 false 1 1.125,1.75 1.292,2.01 0.167,0.26 10 true 5 2.333,1.76 2.521,2.01 0.188,0.25 10 true 7 2.948,1.75 3.167,1.969 0.219,0.219 10 true 3 2.281,0.313 2.49,0.5 0.208,0.188 10 true 8 2.844,0.333 3.042,0.5 0.198,0.167 10 true 4 1.146,0.313 1.385,0.5 0.24,0.188 10 true 6 0.594,0.292 0.74,0.448 0.146,0.156 10 true 2 1.74,1.75 1.906,2.021 0.167,0.271 10 true 9

Using several steps, remove the 10 bearing cap bolts in the sequence shown in the illustration.


c.

Remove the 5 bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 24.REMOVE CAMSHAFT

a.
A259737

Remove the camshaft from the camshaft housing.


Hide 13512 25.REMOVE NO. 2 CAMSHAFT

a.
A259760

Hold up the chain and remove the No. 2 camshaft from the camshaft housing.


b.
A249941

Suspend the chain with a string or equivalent as shown in the illustration.

NOTICE:

Be careful not to drop the chain inside the timing chain cover.



Hide 13523 26.REMOVE CAMSHAFT TIMING SPROCKET

a.

Secure the camshaft in a vice by clamping the hexagonal part using aluminum plates.

NOTICE:

Do not damage the camshaft by tightening the vice excessively.



b.
A259736

Remove the flange bolt and camshaft timing sprocket.

NOTICE:

Do not damage the No. 2 camshaft or camshaft timing sprocket.



Hide 15678A 27.REMOVE OIL CONTROL VALVE FILTER

Hide 11811 28.REMOVE NO. 1 CAMSHAFT BEARING

Hide 11821 29.REMOVE NO. 2 CAMSHAFT BEARING