Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE UNIT
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074906 ENGINE UNIT A

2AR-FXE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 82219A 2.INSTALL SENSOR WIRE

a.

Install the sensor wire with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the knock control sensor connector.


Hide 23814B 3.INSTALL FUEL DELIVERY PIPE

Hide 88431 5.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

a.

Install the No. 1 compressor mounting bracket with the 4 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 16323 6.INSTALL WATER INLET HOUSING

a.

Using an E5 "TORX" socket, install the stud bolt to the water inlet housing.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Using an E8 "TORX" socket, install the stud bolt to the cylinder block.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


c.

Install a new gasket.


d.
A260226
1.083,0.073 1.25,0.229 0.167,0.156 10 true *1 2.021,0.219 2.188,0.375 0.167,0.156 10 true *1 1.458,1.813 1.625,1.969 0.167,0.156 10 true *1 2.385,0.771 2.552,0.927 0.167,0.156 10 true *2
*1 Bolt
*2 Nut


Install the water inlet housing with the 3 bolts and nut.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Install the harness clamp bracket to the water inlet housing with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Install the harness clamp bracket to the cylinder block with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 16031 7.INSTALL WATER INLET SUB-ASSEMBLY

a.

Install a new gasket and the water inlet sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16100 8.INSTALL ENGINE WATER PUMP ASSEMBLY

a.

Install a new gasket and the engine water pump assembly with the 5 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the connector to the engine water pump assembly.


c.

Connect the clamp.


Hide 25611A 9.INSTALL NO. 1 EGR PIPE

a.

Install the No. 1 EGR pipe with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25680 10.INSTALL EGR COOLER ASSEMBLY

a.

Install the No. 4 water by-pass hose, No. 6 water by-pass hose and No. 1 water by-pass pipe with the 2 clamps.


b.
A260670
0.938,0.573 1.104,0.75 0.167,0.177 10 true A 2.427,1.594 2.594,1.792 0.167,0.198 10 true A 2.677,2.104 2.875,2.302 0.198,0.198 10 true B 1.104,2.75 1.271,2.938 0.167,0.188 10 true B

Temporarily install 2 new gaskets and the EGR cooler assembly with the bolt (A) and nut (A).


c.

Temporarily install the bolt (B) and nut (B).


d.

Tighten the 3 bolts and nut.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Make sure that all installation surfaces of the EGR cooler assembly are in even contact when tightening the bolts and nuts.



Hide 25051 11.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 17167 15.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 16261G 16.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose with the clamp.


Hide 22030 17.INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 11452 18.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 19.INSTALL ENGINE HANGERS

a.
A195856
0.098,1.982 0.302,2.172 0.204,0.19 10 *1 0.329,2.071 0.498,2.071 0.498,2.071 0.832,1.568 false 3.032,1.953 3.236,2.143 0.204,0.19 10 *2 3.003,2.054 2.852,2.054 2.852,2.054 2.501,1.265 false
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the 2 engine hangers with the 4 bolts as shown in the illustration.

Part No.
Item Part No.
No. 1 Engine Hanger 12281-36020
No. 2 Engine Hanger 12282-36021
Bolt 91552-81040 or 91552-81025

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


b.

Attach an engine sling device and hang the engine with a chain block.