Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE UNIT
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074906 ENGINE UNIT A

2AR-FXE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


PROCEDURE

Hide 1.REMOVE ENGINE HANGERS

a.
A264710
1,0.229 1.25,0.229 false 2.75,0.24 2.99,0.24 false 1.271,0.125 1.542,0.323 0.271,0.198 10 false *1 3.042,0.146 3.292,0.354 0.25,0.208 10 false *2
*1 No. 1 Engine Hanger
*2 No .2 Engine Hanger


Remove the 2 bolts and 2 engine hangers.


Hide 11452 2.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A260233

Remove the engine oil level dipstick.


b.

Remove the bolt and engine oil level dipstick guide.


c.

Remove the O-ring from the engine oil level dipstick guide.


Hide 17167 3.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A260235

Remove the 4 bolts and No. 1 exhaust manifold heat insulator.


Hide 16261G 4.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
A264717

Disconnect the No. 1 water by-pass hose.


Hide 22030 5.REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 25051 9.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 25680 10.REMOVE EGR COOLER ASSEMBLY

a.
A268332

Disconnect the water by-pass hose.


b.
A260744

Remove the bolt and nut.


c.
A265183

Separate the 2 clamps.


d.

Disconnect the No. 4 water by-pass hose and No. 6 water by-pass hose.


e.
A257336

Remove the bolt, nut and separate the EGR cooler assembly from the engine.


Hide 25611A 11.REMOVE NO. 1 EGR PIPE

a.
A260230

Remove the 2 bolts and No. 1 EGR pipe.


Hide 16100 12.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A259412

Disconnect the harness clamp.


b.
A260241

Disconnect the connector from the engine water pump assembly.


c.
A259348

Remove the 5 bolts and engine water pump assembly.


d.

Remove the gasket from the engine water pump assembly.


Hide 16031 13.REMOVE WATER INLET SUB-ASSEMBLY

a.
A260228

Remove the 2 bolts and water inlet sub-assembly.


b.
A259352

Remove the gasket from the water inlet sub-assembly.


Hide 16323 14.REMOVE WATER INLET HOUSING

a.
A260229

Remove the bolt and harness clamp bracket from the cylinder block.


b.
A260227

Remove the bolt and harness clamp bracket from the water inlet housing.


c.
A260226
1.083,0.073 1.25,0.229 0.167,0.156 10 true *1 2.021,0.219 2.188,0.375 0.167,0.156 10 true *1 1.458,1.813 1.625,1.969 0.167,0.156 10 true *1 2.385,0.771 2.552,0.927 0.167,0.156 10 true *2
*1 Bolt
*2 Nut


Remove the 3 bolts, nut, and water inlet housing.


d.
A260225

Remove the gasket.


e.
A260224

Using an E8 "TORX" socket wrench, remove the stud bolt from the cylinder block.


f.
A261349

Using an E5 "TORX" socket wrench, remove the stud bolt from the water inlet housing.


Hide 88431 15.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A262245

Remove the 4 bolts and No. 1 compressor mounting bracket.


Hide 23814B 17.REMOVE FUEL DELIVERY PIPE

Hide 82219A 18.REMOVE SENSOR WIRE

a.
A260236

Disconnect the knock control sensor connector.


b.

Remove the bolt and knock control sensor wire.