Home › Drivetrain › P314 HYBRID TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE
RM2040EQ _52 Drivetrain _014701 P314 HYBRID TRANSMISSION / TRANSAXLE _0074948 TRANSMISSION CONTROL CABLE A

P314 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before installing the transmission control cable assembly, check that the shift lever position sensor and the shift lever are in neutral.


a.

Pass the transmission control cable assembly from the cabin to the engine compartment.


b.

Install the transmission control cable assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Install the dash panel insulator to the original position.


d.

Install the No. 1 parking brake cable assembly with the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


e.

Install the floor carpet to the original position.


f.

Connect the transmission control cable assembly to the 2 transmission control cable brackets.


g.

Install a new clip to the control cable bracket.


h.
C245030C03
2.833,0.531 2.719,0.531 2.719,0.531 2.646,1.104 false 1.24,1.396 1.063,0.49 1.063,0.49 2.156,1.396 true 1.125,1.615 2.656,2.771 2.656,2.771 2.271,1.615 true 1.438,2.438 1.302,3.021 1.302,3.021 1.177,3.021 true 0.99,2.938 1.156,3.083 0.167,0.146 10 false *1 2.885,0.438 3.052,0.583 0.167,0.146 10 false *2 0.854,0.375 1.021,0.521 0.167,0.146 10 false *a 2.698,2.708 2.865,2.854 0.167,0.146 10 false *b
*1 Transmission Control Cable Assembly
*2 No. 1 Transmission Control Cable Bracket
*a Claw A
*b Claw B


Install the transmission control cable assembly to the No. 1 transmission control cable bracket

NOTICE:
·

Make sure that the claws A on the clip are securely fit into the bracket holes.

·

Make sure that the cable is securely installed inside of the claws B of the clip.




i.

Connect the transmission control cable to the control shaft lever with the nut.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


j.

Engage the 2 claws to connect the transmission control cable assembly.


k.
C194520C19
2.25,2.573 2.594,2.573 false 1.958,1.75 2.094,1.531 2.094,1.531 2.198,1.531 false 1.635,0.906 1.823,1.083 0.188,0.177 10 true *a 1.792,1.365 1.979,1.542 0.188,0.177 10 false *a 2.469,0.875 2.656,1.052 0.188,0.177 10 false *b 2.229,1.458 2.417,1.635 0.188,0.177 10 false *1 2.229,2.333 2.417,2.51 0.188,0.177 10 false *b 2.615,2.49 2.802,2.667 0.188,0.177 10 false *2
*1 Slider
*2 Lock Piece
*a Slide
*b Pull


Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.


l.
C241614C05
1.281,2.24 1.406,2.042 1.406,2.042 1.542,2.042 false 1.583,1.958 1.875,2.146 0.292,0.188 10 false *1
*1 Lock Piece


Install the end of transmission control cable to the lower shift lever assembly.

NOTICE:
·

Check that the lock piece is pulled up.

·

Install the cable end all the way to the base of the pin.




m.

Push the lock piece into the adjuster case.

NOTICE:
·

Check that the shift lever position sensor and the shift lever are in neutral.

·

Securely push in the lock piece until the slider lock is engaged.




Hide 3.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 4.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 5.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17750A 6.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 7.INSTALL COOL AIR INTAKE DUCT SEAL