Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM
RM2040EQ _53 Suspension _014705 FRONT SUSPENSION _0074967 FRONT LOWER SUSPENSION ARM A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM  INSTALLATION  


PROCEDURE

Hide 48069 1.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for LH Side)

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.


b.
C167143E01
0.656,0.357 0.795,0.515 0.139,0.158 10 1 1.147,0.24 1.286,0.398 0.139,0.158 10 2 2.467,0.926 2.613,1.077 0.146,0.150 10 3

Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt 1, 2 : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt 3 : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

While keeping the nut from rotating, tighten the bolt.



c.

Install the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
75 N*m (765 kgf*cm, 55 ft.*lbf)


Hide 12372A 2.INSTALL ENGINE MOUNTING INSULATOR LH (for LH Side)

a.
C242569C02
1.771,0.813 2.24,0.813 false 2.25,0.719 2.458,0.917 0.208,0.198 9 false *a
*a Pin


Set the engine mounting insulator LH on the front frame assembly.


b.

Slowly lower the engine assembly with transaxle using a jack and a wooden block.

NOTICE:
·

Match the position of the pin (stopper).

·

Do not position the wooden block on the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Ensure that the jack and wooden block are stable.




c.
C246189C01
1.313,1.25 1.073,1.563 1.073,1.563 1.073,2.26 false 2.375,0.948 2.573,1.167 0.198,0.219 10 true *a 0.938,2.281 1.396,2.552 0.458,0.271 10 false SST
*a Fulcrum Length


Using SST, install the nut to the engine mounting insulator LH.

SST
09961-00950  

Torque:
without SST : 95 N*m (969 kgf*cm, 70 ft.*lbf)
with SST : 68 N*m (695 kgf*cm, 50 ft.*lbf)

NOTICE:
·

Use a torque wrench with a fulcrum length of 380 mm (1.25 ft.).

·

This torque value is effective when SST is parallel to the torque wrench.




d.
C243740

Install the engine mounting insulator LH with the 3 nuts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


e.

Install the 2 hole plugs.


Hide 48068 3.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for RH Side)

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly RH.


b.
C239314E01
2.639,0.27 2.746,0.422 0.106,0.152 10 1 2.15,0.233 2.257,0.385 0.106,0.152 10 2 0.853,0.937 0.959,1.089 0.106,0.152 10 3

Install the front lower No. 1 suspension arm sub-assembly RH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt 1, 2 : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt 3 : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

While keeping the nut from rotating, tighten the bolt.



c.

Install the front lower No. 1 suspension arm sub-assembly RH to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
75 N*m (765 kgf*cm, 55 ft.*lbf)


Hide 12362 4.INSTALL ENGINE MOUNTING INSULATOR RH (for RH Side)

a.
C247223C02
2.479,0.427 2.75,0.802 2.75,0.802 2.448,1.26 false 2.792,0.719 3.063,0.979 0.271,0.26 10 false *a
*a Cutout


Set the engine mounting insulator RH on the front frame assembly.


b.

Slowly lower the engine assembly with transaxle using a jack and a wooden block.

NOTICE:
·

Match the position of the cutout (stopper).

·

Do not position the wooden block on the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Ensure that the jack and wooden block are stable.




c.
C239301C06
2.125,1.208 2.552,1.677 2.552,1.677 2.552,2.406 false 0.927,0.906 1.135,1.094 0.208,0.188 10 true *a 2.417,2.427 2.823,2.708 0.406,0.281 10 false SST
*a Fulcrum Length


Using SST, install the nut to the engine mounting insulator RH.

SST
09961-00950  

Torque:
without SST : 95 N*m (969 kgf*cm, 70 ft.*lbf)
with SST : 68 N*m (695 kgf*cm, 50 ft.*lbf)

NOTICE:
·

Use a torque wrench with a fulcrum length of 380 mm (1.25 ft.).

·

This torque value is effective when SST is parallel to the torque wrench.




d.
C247221

Install the engine mounting insulator RH with the 3 nuts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


e.

Install the 2 hole plugs.


Hide 12361A 5.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the front engine mounting insulator to the front frame assembly with the 3 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 89465 6.CONNECT OXYGEN SENSOR

a.

Connect the oxygen sensor connector.


Hide 82124 7.CONNECT NO. 4 ENGINE WIRE

a.

Connect the No. 4 engine wire to the front frame assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 53737B 8.INSTALL FRONT FENDER APRON SEAL LH (for LH Side)

Hide 53736 9.INSTALL FRONT FENDER APRON SEAL RH (for RH Side)

Hide 51442C 10.INSTALL ENGINE UNDER COVER LH

Hide 51441C 11.INSTALL ENGINE UNDER COVER RH

Hide 53852K 12.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851Z 13.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

Hide 12309 14.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

Hide 12327A 15.INSTALL NO. 2 ENGINE MOUNTING STAY RH

Hide 55702A 17.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 18.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 19.INSTALL FRONT WHEELS

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide G9200 20.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 21.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT