Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM2040EQ _53 Suspension _014706 REAR SUSPENSION _0074975 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.

Install the 2 hole plugs to the rear suspension member sub-assembly.


Hide 52272A 2.INSTALL REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH

a.
C253274C01
2.813,0.875 2.813,0.885 false
V100135

Front of the Vehicle


Temporarily install a new rear suspension member body mounting front cushion LH to the position shown in the illustration.


b.

Using SST and a press, install the rear suspension member body mounting front cushion LH to the rear suspension member sub-assembly.

C240560N08
1.573,1.073 1.281,1.073 false 1.188,1.313 0.927,1.313 false 1.438,2.188 1.188,2.188 false 1,0.99 1.365,1.229 0.365,0.24 10 false SST 0.646,1.229 1.01,1.438 0.365,0.208 10 false SST 0.906,2.104 1.26,2.354 0.354,0.25 10 false SST

SST
09710-30012  (09710-04061)
09950-60010  (09951-00650)
09950-70010  (09951-07100)

HINT:

Slowly press in the rear suspension member body mounting front cushion LH.



c.
C240562

While observing from the side, press in the rear suspension member body mounting front cushion LH until there is no clearance between the rear suspension member body mounting front cushion LH and the rear suspension member sub-assembly as shown in the illustration.

NOTICE:

Do not press the rear suspension member excessively, or it will easily deform.



Hide 52271E 3.INSTALL REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH

a.
C253275C01
2.865,0.979 2.854,0.969 false
V100135

Front of the Vehicle


Temporarily install a new rear suspension member body mounting front cushion RH to the position shown in the illustration.


b.

Using SST and a press, install the rear suspension member body mounting front cushion RH to the rear suspension member sub-assembly.

C240566N08
5.542,1.021 5.896,1.021 false 5.938,1.25 6.146,1.25 false 5.677,2.229 6,2.229 false 5.938,0.948 6.292,1.167 0.354,0.219 10 false SST 6.188,1.177 6.542,1.396 0.354,0.219 10 false SST 6.052,2.156 6.438,2.385 0.385,0.229 10 false SST

SST
09710-30012  (09710-04061)
09950-60010  (09951-00650)
09950-70010  (09951-07100)

HINT:

Slowly press in the rear suspension member body mounting front cushion RH.



c.
C240567

While observing from the side, press in the rear suspension member body mounting front cushion RH until there is no clearance between the rear suspension member body mounting front cushion RH and the rear suspension member sub-assembly as shown in the illustration.

NOTICE:

Do not press the rear suspension member excessively, or it will easily deform.



Hide 52275A 4.INSTALL REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)

a.
C253276C01
2.792,0.938 2.802,0.927 false
V100135

Front of the Vehicle


Temporarily install a new rear suspension member body mounting rear cushion (LH side) to the position shown in the illustration.


b.

Using SST and a press, install the rear suspension member body mounting rear cushion (LH side) to the rear suspension member sub-assembly.

C240561N08
5.448,1.073 5.781,1.073 false 5.844,1.292 6.031,1.292 false 5.594,2.292 5.917,2.292 false 5.823,0.99 6.208,1.188 0.385,0.198 10 false SST 6.073,1.208 6.417,1.406 0.344,0.198 10 false SST 5.958,2.208 6.313,2.396 0.354,0.188 10 false SST

SST
09710-30012  (09710-04061)
09950-60010  (09951-00650)
09950-70010  (09951-07100)

HINT:

Slowly press in the rear suspension member body mounting rear cushion.



c.
C240567

While observing from the side, press in the rear suspension member body mounting rear cushion (LH side) until there is no clearance between the rear suspension member body mounting rear cushion (LH side) and the rear suspension member sub-assembly as shown in the illustration.

NOTICE:

Do not press the rear suspension member excessively, or it will easily deform.



Hide 52275A 5.INSTALL REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

HINT:

Perform the same procedure as the LH side.


Hide 51249 6.INSTALL REAR SUSPENSION MEMBER DAMPER

a.

Install the rear suspension member damper to the rear suspension member sub-assembly with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48720A 7.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 8.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 48740F 9.TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 10.TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 51206A 11.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C249991C12
0.365,2.188 0.188,2.188 0.188,2.188 0.188,2.323 false 1.177,1.74 1.042,1.74 1.042,1.74 1.042,2.344 false 1.146,1.865 1.042,1.865 false 0.708,1.948 0.354,1.948 false 2.073,1.688 2.229,1.688 false 0.094,2.333 0.313,2.552 0.219,0.219 10 false *1 0.958,2.354 1.177,2.563 0.219,0.208 10 false *2 0.198,1.865 0.406,2.073 0.208,0.208 10 false *2 2.26,1.604 2.49,1.833 0.229,0.229 10 false *2
*1 Engine Lifter
*2 Attachment
V100155

Attachment Placement Location


Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools.

NOTICE:
·

Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.

·

Use the attachments to keep the rear suspension member sub-assembly level.




b.

Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and the vehicle body.

NOTICE:

When raising the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.



c.

Install the rear suspension member sub-assembly, rear suspension member lower stopper sub-assembly LH and rear suspension member lower stopper sub-assembly RH with the 4 nuts.

C241285C06
1.823,3.375 1.406,3.375 1.406,3.375 1.406,3.604 false 5.5,3.365 5.823,3.365 5.823,3.365 5.823,3.563 false 6.74,0.906 6.99,1.177 0.25,0.271 10 false (A) 6.833,0.125 7.115,0.375 0.281,0.25 10 false (B) 0.521,0.896 0.75,1.156 0.229,0.26 10 false (A) 0.417,0.125 0.729,0.406 0.313,0.281 10 false (B) 1.313,3.615 1.521,3.781 0.208,0.167 10 false *1 5.74,3.583 5.958,3.781 0.219,0.198 10 false *1
*1 Rear suspension member lower stopper - -


Torque:
Nut A : 55 N*m (561 kgf*cm, 41 ft.*lbf)
Nut B : 38 N*m (387 kgf*cm, 28 ft.*lbf)


d.

Install the 2 rear suspension member lower stoppers with the 2 bolts to the rear suspension member sub-assembly.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)

NOTICE:

Be sure to install the rear suspension member sub-assembly with the rear suspension member lower stoppers in the correct direction, as shown in the illustration.



Hide 17573A 12.INSTALL NO. 3 EXHAUST PIPE SUPPORT BRACKET

a.

Install the No. 3 exhaust pipe support bracket to the rear suspension member sub-assembly with the 2 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


Hide 58219C 13.INSTALL REAR CENTER FLOOR END PLATE

a.

Install the rear center floor end plate to the rear suspension member sub-assembly with the 2 bolts.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 48720A 14.CONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 15.CONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 48740F 16.CONNECT REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 17.CONNECT REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 48812 18.INSTALL REAR STABILIZER BAR

Hide 48840A 19.CONNECT REAR STABILIZER LINK ASSEMBLY LH

a.

Connect the rear stabilizer link assembly LH to the rear stabilizer bar with nut.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)

If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.


Hide 48830D 20.CONNECT REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 48720A 22.FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 23.FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 48740F 24.FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C244179N06
3.177,1.177 3.396,1.354 0.219,0.177 10 (A) 0.625,1.938 0.844,2.115 0.219,0.177 10 (B)

Fully tighten the bolt (A).

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


b.

Fully tighten the bolt (B).

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

NOTICE:

When fully tightening the bolt, keep the nut from rotating.



Hide 48730F 25.FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 58399B 26.INSTALL NO. 2 FLOOR UNDER COVER

Hide 58398H 27.INSTALL NO. 1 FLOOR UNDER COVER

Hide 17420 28.INSTALL CENTER EXHAUST PIPE ASSEMBLY

Hide 29.INSTALL REAR WHEELS

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 30.INSPECT AND ADJUST REAR WHEEL ALIGNMENT