Home › Brake › BRAKE (REAR) › REAR BRAKE
RM2040EQ _54 Brake _014711 BRAKE (REAR) _0074992 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C238505C10
1.948,1.281 2.938,1.198 2.938,1.198 1.927,1.198 false 2.979,1.104 3.229,1.365 0.25,0.26 10 false *a
*a Matchmark


Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.

NOTICE:

When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 42491 2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Install the parking brake shoe adjusting hole plug.


Hide 47722A 3.INSTALL DISC BRAKE CYLINDER MOUNTING

a.
C243125

Install the disc brake cylinder mounting with the 2 bolts.

Torque:
62 N*m (630 kgf*cm, 46 ft.*lbf)


Hide 4.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.
C239548C02
1.375,0.802 1.365,0.792 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



b.
C243124

Install the 2 rear disc brake bushing dust boots to the disc brake cylinder mounting.


Hide 5.INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSHING

a.
C211757C07
1.74,1.156 1.74,1.146 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the rear disc brake cylinder slide pin.


b.

Install a new rear disc brake cylinder slide bushing to the rear disc brake cylinder slide pin.


Hide 47814 6.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN (for Lower Side)

a.
C211758C07
1.24,0.927 1.229,0.927 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the rear disc brake cylinder slide pin.


b.
C243123

Install the rear disc brake cylinder slide pin to the disc brake cylinder mounting.


c.

Push the rear disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.


Hide 47814 7.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN (for Upper Side)

a.
C211759C06
1.333,0.875 1.344,0.875 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the rear disc brake cylinder slide pin.


b.
C243122

Install the rear disc brake cylinder slide pin to the disc brake cylinder mounting.


c.

Push the rear disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.


Hide 47716A 8.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.
C273541C01
0.833,0.521 1.052,0.521 1.052,0.521 1.24,0.646 false 2.292,1.635 2.625,1.833 2.625,1.833 2.844,1.833 false 0.677,0.469 0.99,0.625 0.313,0.156 10 *1 2.885,1.781 3.198,1.938 0.313,0.156 10 *2 1.323,0.104 1.479,0.302 0.156,0.198 10 A 2.813,1.063 2.969,1.26 0.156,0.198 10 b 2.792,1.323 2.948,1.521 0.156,0.198 10 B 1.885,0.083 2.042,0.281 0.156,0.198 10 a
*1 Rear Disc Brake Pad Support Plate
*2 Disc Brake Cylinder Mounting


Install the 2 rear disc brake pad support plates to the disc brake cylinder mounting.

NOTICE:

Firmly push to install the rear disc brake pad support plate and disc brake cylinder mounting against each other so that there is no clearance between the surfaces A and a, and B and b.



Hide 04946 9.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.
C239557

Install the pad wear indicator plate to each rear disc brake pad.

NOTICE:

Install each pad wear indicator plate in the correct position and direction.



b.
C239556C02
0.979,1.479 0.979,1.49 false
V100155

Disc Brake Grease


Apply disc brake grease to the inside of the rear disc brake anti-squeal shims.


c.
C239558

Install the rear disc brake anti-squeal shim to each rear disc brake pad with pad wear indicator plate.

NOTICE:
·

Disc brake grease may seep out slightly from the areas where the rear disc brake anti-squeal shims are installed.

·

Make sure that disc brake grease is not applied onto the lining surface.




Hide 04466 10.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 rear disc brake pads with rear disc brake anti-squeal shim kit to the disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.



Hide 47850 11.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C239570C04
2.26,0.448 2.594,0.74 0.333,0.292 10 false *b 2.74,1.833 3.052,2.156 0.313,0.323 10 false *a
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin, and install the rear disc brake cylinder assembly to the disc brake cylinder mounting with the 2 bolts.

Torque:
27 N*m (270 kgf*cm, 20 ft.*lbf)


Hide 47319F 12.CONNECT REAR FLEXIBLE HOSE

a.
C243121C07
1.885,1 2.458,1.563 2.458,1.563 2.656,1.563 false 2.677,1.469 2.938,1.729 0.26,0.26 10 false *a
*a Lock Hole


Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
33 N*m (340 kgf*cm, 25 ft.*lbf)

NOTICE:

Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



Hide 13.CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2AR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION


b.

Perform the following procedure if air bleeding is not necessary:

i.

Connect the reservoir level switch connector.




Hide 14.BLEED BRAKE LINE

Hide 55702A 15.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 16.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 17.ADJUST PARKING BRAKE

Hide 18.INSTALL REAR WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)