The A/C inverter assembly monitors the voltage of the HV battery. It stops compressor control and stores the DTC when the monitored voltage is outside the specified range.
The DTC will be stored as a history DTC. Compressor control may not resume unless the power switch is turned off.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1471/71 | A/C Inverter High Voltage Power Resource System Malfunction | ·
Open or short in A/C inverter high voltage power resource system. ·
The boost inverter is broken or malfunctioning. |
·
Electric vehicle fuse ·
No. 4 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly) ·
Compressor with motor assembly ·
Hybrid control system ·
CAN communication system |
Memorized |
Wear electrically insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Be sure to carry the removed service plug grip because other workers may install it by mistake.
Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.
Using the intelligent tester to check if the CAN communication system is functioning normally.
| Result | Proceed to |
|---|---|
| CAN DTC is not output | A |
| CAN DTC is output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if DTCs for the hybrid control system are output using the intelligent tester.
Hybrid control system DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Turn the power switch off.
Remove the service plug grip.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL
Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.
After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.
Remove the connector cover assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL
Be sure to prevent foreign objects or water from entering the inverter with converter assembly.
| *a | Electric Vehicle Fuse |
Check that bolts A and B are tightened securely.
Measure the resistance according to the value(s) in the table below.
| Tester Item
(Tester Connection) |
Condition | Specified Condition |
|---|---|---|
| Electric vehicle fuse(A - B) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Disconnect the No. 4 engine wire connector.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-1 (PE) - G2-1 (ACPE) | Always | Below 1 Ω |
| G1-2 (PB) - G2-2 (ACPB) | Always | Below 1 Ω |
| G1-1 (PE) - Body ground | Always | 10 kΩ or higher |
| G1-2 (PB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG