Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2012.02–2015.04
RM2040EQ _58 Vehicle Interior _014730 HEATING / AIR CONDITIONING _0075108 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1498/98  Communication Malfunction (A/C Inverter Local)  


DESCRIPTION

The power management control ECU and compressor with motor assembly transmit information to one another via a communication line. Compressor control is stopped and the DTC is stored if communication information is cut off or abnormal information occurs.

The DTC is also detected if high-voltage power supplied from the inverter with converter assembly to the compressor control circuit is shut off.

The DTC will be stored as a history DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1498/98 Communication Malfunction (A/C Inverter Local)
·

Communication line error or open between the power management control ECU and compressor with motor assembly.

·

High-voltage power source is shut off.


·

Harness or connector between power management control ECU, compressor with motor assembly and body ground

·

Power management control ECU

·

Compressor with motor assembly

·

No. 4 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly)

·

Electric vehicle fuse

·

CAN communication system

·

Hybrid control system


Memorized

WIRING DIAGRAM

E235673E01
0.281,6.281 1.333,6.74 1.052,0.458 10 false Compressor with Motor Assembly 5.781,3.958 7.104,4.302 1.323,0.344 10 false Power Management Control ECU 6.052,1.844 6.344,1.99 0.292,0.146 10 false STB 6.052,2.854 6.344,3 0.292,0.146 10 false ITE 6.052,3.375 6.344,3.521 0.292,0.146 10 false CLK 6.052,2.354 6.292,2.5 0.24,0.146 10 false ETI 0.854,1.833 1.188,1.979 0.333,0.146 10 false STBI 0.927,2.854 1.188,3 0.26,0.146 10 false DIN 0.906,3.344 1.198,3.49 0.292,0.146 10 false CLK 0.948,3.917 1.188,4.063 0.24,0.146 10 false IG1 0.865,4.479 1.198,4.625 0.333,0.146 10 false GND 0.979,5.281 1.292,5.51 0.313,0.229 10 false PE 0.979,5.781 1.344,6.042 0.365,0.26 10 false PB 0.771,2.333 1.188,2.479 0.417,0.146 10 false DOUT 1.333,1.833 1.615,1.979 0.281,0.146 10 false E65 1.333,2.344 1.615,2.49 0.281,0.146 10 false E65 1.333,2.844 1.615,2.99 0.281,0.146 10 false E65 1.333,3.365 1.615,3.51 0.281,0.146 10 false E65 1.333,4.479 1.615,4.646 0.281,0.167 10 false E65 1.333,3.917 1.615,4.063 0.281,0.146 10 false E65 5.781,1.74 5.969,1.885 0.188,0.146 10 false 20 5.792,2.24 5.969,2.385 0.177,0.146 10 false 30 5.792,2.76 5.969,2.906 0.177,0.146 10 false 31 5.792,3.271 5.969,3.417 0.177,0.146 10 false 19 4.927,7.115 7.063,7.375 2.135,0.26 10 false Inverter with Converter Assembly 5.229,5.677 5.333,5.844 0.104,0.167 10 false 2 5.229,5.156 5.333,5.323 0.104,0.167 10 false 1 1.365,5.25 1.74,5.521 0.375,0.271 10 false G1 1.365,5.771 1.729,6.031 0.365,0.26 10 false G1 1.427,5.073 1.531,5.219 0.104,0.146 10 false 1 1.438,5.583 1.542,5.75 0.104,0.167 10 false 2 1.417,1.667 1.521,1.813 0.104,0.146 10 false 4 1.417,2.146 1.521,2.313 0.104,0.167 10 false 3 1.417,2.667 1.521,2.813 0.104,0.146 10 false 2 1.417,3.167 1.521,3.333 0.104,0.167 10 false 1 1.417,3.74 1.521,3.885 0.104,0.146 10 false 6 1.427,4.292 1.531,4.458 0.104,0.167 10 false 5 5.406,5.156 5.813,5.302 0.406,0.146 10 false ACPE 5.406,5.667 5.813,5.813 0.406,0.146 10 false ACPB 5.719,5.938 6.229,6.531 0.51,0.594 10 false Electric Vehicle Fuse 2.594,4.042 3.115,4.188 0.521,0.146 10 false A/C-IG1 4.167,3.906 5.563,4.052 1.396,0.146 10 false from IG1 NO. 1 Relay 2.26,7.135 3.979,7.281 1.719,0.146 10 false : CAN Communication Line 4.927,6.948 5.177,7.156 0.25,0.208 10 false G2 5.781,3.813 6.073,4 0.292,0.188 10 false A38 0.365,1.063 2.646,1.26 2.281,0.198 10 false Air Conditioning Amplifier Assembly 2.729,6.313 3.938,6.542 1.208,0.229 10 false No. 4 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear electrically insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Be sure to carry the removed service plug grip because other workers may install it by mistake.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.

·

Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.CHECK DIAGNOSTIC TROUBLE CODE

B

2.CHECK DIAGNOSTIC TROUBLE CODE
a.

Check if DTCs for the hybrid control system are output using the intelligent tester.

OK:

Hybrid control system DTCs are not output.



Result:
Result Proceed to
DTC is not output A
Only DTC P3108 is output A
DTCs other than P3108 are output B



A

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.

Disconnect the E65 compressor with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Item Condition Specified Condition
E65-5 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - AUXILIARY BATTERY, GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - AUXILIARY BATTERY, GROUND)
a.

Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E65-6 (IG1) - E65-5 (GND) Power switch on (IG) 11 to 14 V
E65-6 (IG1) - E65-5 (GND) Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
a.

Disconnect the A38 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E65-1 (CLK) - A38-19 (CLK) Always Below 1 Ω
E65-2 (DIN) - A38-31 (ITE) Always Below 1 Ω
E65-3 (DOUT) - A38-30 (ETI) Always Below 1 Ω
E65-1 (CLK) - Body ground Always 10 kΩ or higher
E65-2 (DIN) - Body ground Always 10 kΩ or higher
E65-3 (DOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ELECTRIC VEHICLE FUSE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ELECTRIC VEHICLE FUSE
CAUTION:

Be sure to wear insulated gloves.


a.

Turn the power switch off.


b.

Remove the service plug grip.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.



c.

Remove the connector cover assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL

NOTICE:

Be sure to prevent foreign objects or water from entering the inverter with converter assembly.



d.
E230460C03
2.177,0.833 1.208,0.833 false 2.177,1.448 1.198,1.448 false 0.333,0.375 0.646,0.625 0.313,0.25 10 false *a 1.042,0.75 1.167,0.948 0.125,0.198 10 false A 1.042,1.365 1.167,1.563 0.125,0.198 10 false B
*a Electric Vehicle Fuse


Check that bolts A and B are tightened securely.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Item
(Tester Connection)
Condition Specified Condition
Electric vehicle fuse(A - B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 4 ENGINE WIRE

NG

7.INSPECT NO. 4 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Disconnect the No. 4 engine wire connector.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Item
(Tester Connection)
Condition Specified Condition
G1-1 (PE) - G2-1 (ACPE) Always Below 1 Ω
G1-2 (PB) - G2-2 (ACPB) Always Below 1 Ω
G1-1 (PE) - Body ground Always 10 kΩ or higher
G1-2 (PB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG

8.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY
a.

Replace the compressor with motor assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL

HINT:

Since the compressor with motor assembly cannot be inspected while it is removed from the vehicle, replace the compressor with motor assembly with a new or a known good one and check that the condition returns to normal.



b.

Check for the DTC.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
Result:
Result Proceed to
DTC B1498/98 is not output A
DTC B1498/98 is output B




A

END (COMPRESSOR WITH MOTOR ASSEMBLY WAS DEFECTIVE)

B