Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › 2012.02–2015.04
RM2040EQ _58 Vehicle Interior _014730 HEATING / AIR CONDITIONING _0075123 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  INSTALLATION  


PROCEDURE

Hide 88460 1.INSTALL COOLER CONDENSER ASSEMBLY

a.
E248177

Temporarily install the cooler condenser assembly to the radiator assembly with the 2 bolts <A>.


b.

Insert the cooler condenser assembly with radiator assembly.


c.
E248176E02
2.677,1.333 3,1.521 0.323,0.188 10 false <A> 0.438,2.292 0.76,2.479 0.323,0.188 10 true <A> 2.417,2.115 2.76,2.323 0.344,0.208 10 true <C> 1.042,1.667 1.385,1.865 0.344,0.198 10 true <C> 2.885,0.896 3.281,1.135 0.396,0.24 10 true <B> 0.323,0.063 0.688,0.281 0.365,0.219 10 true <B>

Temporarily install the 2 bolts <B> and the 2 bolts <C>.


d.

Install the cooler condenser assembly with the 2 bolts <A>, 2 bolts<B> and 2 bolts <C>.

Torque:
Bolt<A>, <C> : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
Bolt<B> : 5.0 N*m (51 kgf*cm, 44 in.*lbf)

HINT:

If the cooler condenser assembly is replaced with a new one, add compressor oil to the new cooler condenser assembly.


Capacity:

40 cc (1.4 fl. oz.)


Compressor oil:

ND-OIL 11 or equivalent



Hide 88710E 2.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the tube and the connector of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.


d.

Install the air conditioner tube and accessory assembly to the cooler condenser assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88711 3.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the vinyl tape from the pipe and the connector of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


d.

Install the No. 1 cooler refrigerant discharge hose to the cooler condenser assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 53294C 4.INSTALL RADIATOR SIDE DEFLECTOR LH

a.
E230563E02
1.865,0.885 2.104,1.146 0.24,0.26 10 false (1) 1.802,2.042 2.042,2.302 0.24,0.26 10 false (2)

Engage the guide and 3 claws to install the radiator side deflector LH as shown in the illustration.


Hide 53293C 5.INSTALL RADIATOR SIDE DEFLECTOR RH

Hide 53216A 6.INSTALL UPPER RADIATOR SUPPORT

Hide 16470 8.INSTALL RADIATOR RESERVE TANK ASSEMBLY

Hide 17750A 10.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 52021 11.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

Hide 52611 12.INSTALL FRONT BUMPER ENERGY ABSORBER

Hide 13.INSTALL FRONT BUMPER ASSEMBLY

Hide 14. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 53301 17.ADJUST HOOD SUB-ASSEMBLY