Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1273/73  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274/74  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1466/33  Rear Speed Sensor RH Circuit  C1467/34  Rear Speed Sensor LH Circuit  


DESCRIPTION

Each speed sensor detects the wheel speed and sends signals to the skid control ECU. These signals are used for ABS control.

DTCs C1273/73 and C1274/74 can be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1273/73 and C1274/74 are output only in Test Mode.

C276868E01
1.583,0.854 1.583,0.281 1.583,0.281 1.875,0.281 false 1.938,0.198 3.771,0.396 1.833,0.198 10 Speed Sensor 1.01,2.208 2.844,2.406 1.833,0.198 10 Speed Sensor Rotor 4.042,2.167 5.875,2.365 1.833,0.198 10 Low speed 5,2.156 6.833,2.354 1.833,0.198 10 High speed 6.063,1.271 7.156,1.521 1.094,0.25 10 1.4 V 6.094,1.656 7.156,1.875 1.063,0.219 10 0.7 V

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor RH

·

Sensor installation

·

Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH)


ABS Test Mode DTC
C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor LH

·

Sensor installation

·

Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH)


ABS Test Mode DTC
C1466/33 Rear Speed Sensor RH Circuit 521
522
523
524
526
527
528
·

INF Code: 521

·

While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 522

·

A malfunction occurs in 2 or more wheels.



·

INF Code: 523

·

An open is detected in the speed sensor signal circuit for 0.05 seconds or more.



·

INF Code: 524

·

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 526

·

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 527

·

While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 528

·

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 521, 522, 524, 527

·

Open or short in speed sensor


·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


·

Open or short in wire harness


·

Improperly connected connector, deformation or corrosion of terminals


·

Rear speed sensor RH


·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 523

·

Open or short in speed sensor


·

Open or short in wire harness


·

Improperly connected connector, deformation or corrosion of terminals


·

Rear speed sensor RH


·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 526, 528

·

Open or short in wire harness


·

Skid control ECU (Brake booster with master cylinder assembly)



ABS DTC
C1467/34 Rear Speed Sensor LH Circuit 531
532
533
534
536
537
538
·

INF Code: 531

·

While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 532

·

A malfunction occurs in 2 or more wheels.



·

INF Code: 533

·

An open is detected in the speed sensor signal circuit for 0.05 seconds or more.



·

INF Code: 534

·

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 536

·

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 537

·

While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 538

·

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 531, 532, 534, 537

·

Open or short in speed sensor


·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


·

Open or short in wire harness


·

Improperly connected connector, deformation or corrosion of terminals


·

Rear speed sensor LH


·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 533

·

Open or short in speed sensor


·

Open or short in wire harness


·

Improperly connected connector, deformation or corrosion of terminals


·

Rear speed sensor LH


·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 536, 538

·

Open or short in wire harness


·

Skid control ECU (Brake booster with master cylinder assembly)



ABS DTC

HINT:
·

DTCs C1466/33 and C1273/73 are for the rear speed sensor RH.

·

DTCs C1467/34 and C1274/74 are for the rear speed sensor LH.



WIRING DIAGRAM

C220952E12
0.927,1.417 2.448,1.583 1.521,0.167 10 false Rear Speed Sensor RH 2.229,0.917 2.49,1.208 0.26,0.292 10 false 1 1.063,0.917 1.302,1.146 0.24,0.229 10 false 2 0.948,3.365 2.469,3.531 1.521,0.167 10 false Rear Speed Sensor LH 2.229,2.865 2.344,3.031 0.115,0.167 10 false 1 1.063,2.865 1.177,3.031 0.115,0.167 10 false 2 4.99,4.083 7.052,4.604 2.063,0.521 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.771,1.01 5.948,1.156 0.177,0.146 10 false 9 5.979,0.552 6.417,0.792 0.438,0.24 10 false RR+ 5.698,0.469 6.021,0.708 0.323,0.24 10 false 22 5.979,1.125 6.344,1.375 0.365,0.25 10 false RR- 5.771,2.969 6,3.115 0.229,0.146 10 false 7 5.979,2.531 6.479,2.823 0.5,0.292 10 false RL+ 5.698,2.406 6.01,2.646 0.313,0.24 10 false 20 5.979,3.083 6.354,3.375 0.375,0.292 10 false RL- 1.01,1.125 1.302,1.292 0.292,0.167 10 false h1 4.24,1.521 4.906,1.688 0.667,0.167 10 false Shielded 4.26,3.521 4.948,3.76 0.688,0.24 10 false Shielded 4.667,4.083 5.01,4.333 0.344,0.25 10 false A28 1.354,1.125 1.74,1.333 0.385,0.208 10 false RR+ 1.76,1.125 2.146,1.344 0.385,0.219 10 false RR- 1.344,3.073 1.698,3.219 0.354,0.146 10 false RL+ 1.771,3.073 2.021,3.219 0.25,0.146 10 false RL- 2.99,0.344 3.208,0.583 0.219,0.24 10 false 1 2.99,0.917 3.104,1.083 0.115,0.167 10 false 2 2.198,1.135 2.49,1.302 0.292,0.167 10 false h1 0.677,1.75 2.542,1.917 1.865,0.167 10 false Skid Control Sensor Wire RH 2.906,0.573 3.302,0.74 0.396,0.167 10 false hO1 2.906,1.135 3.302,1.302 0.396,0.167 10 false hO1 1.031,3.073 1.281,3.24 0.25,0.167 10 false i1 2.229,3.073 2.479,3.24 0.25,0.167 10 false i1 0.677,3.677 2.656,3.896 1.979,0.219 10 false Skid Control Sensor Wire LH 2.99,2.302 3.104,2.469 0.115,0.167 10 false 1 2.99,2.875 3.229,3.083 0.24,0.208 10 false 2 2.938,2.51 3.26,2.677 0.323,0.167 10 false iN1 2.938,3.083 3.281,3.25 0.344,0.167 10 false iN1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Open Rear speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
a.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

b.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the power switch off.


b.

Perform the sensor check in the Test Mode Procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the power switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1466/33 and C1467/34 are not output. A
DTCs C1466/33 and/or C1467/34 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
5.CHECK REAR SPEED SENSOR INSTALLATION
a.
C144931C04
0.99,1.51 1.208,0.979 1.208,0.979 1.427,0.979 false 0.156,0.115 1.563,0.323 1.406,0.208 10 false *1 1.458,0.885 2.344,1.073 0.885,0.188 10 false *a 0.885,2.792 1.146,2.979 0.26,0.188 10 false *b 2.354,2.802 2.688,3.073 0.333,0.271 10 false *c
*1 Rear Speed Sensor
*a No clearance
*b OK
*c NG


Turn the power switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and rear axle carrier.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)
a.
C275487C04
0.188,0.677 0.51,0.906 0.323,0.229 1.823,0.698 2.146,0.927 0.323,0.229 0.198,2.844 0.521,3.073 0.323,0.229 1.833,2.865 2.156,3.094 0.323,0.229 0.563,2.073 0.969,1.333 false 2.219,2.073 2.427,1.573 false 1.552,2.073 1.229,1.323 false 2.938,2.073 2.667,1.594 false 1.563,4.396 1.24,3.646 false 0.552,4.385 0.958,3.646 false 2.125,4.406 2.333,3.906 false 2.948,4.396 2.677,3.917 false 0.25,0.125 0.563,0.323 0.313,0.198 10 *a 0.25,0.354 0.563,0.552 0.313,0.198 10 *A 0.281,0.708 0.594,0.906 0.313,0.198 10 h1 1.875,0.729 2.188,0.927 0.313,0.198 10 hO1 1.021,0.51 1.333,0.708 0.313,0.198 10 *b 2.396,0.552 2.708,0.75 0.313,0.198 10 *c 0.302,2.563 0.615,2.76 0.313,0.198 10 *B 0.313,2.875 0.625,3.073 0.313,0.198 10 i1 1.906,2.896 2.219,3.094 0.313,0.198 10 iN1 2.417,3.073 2.729,3.271 0.313,0.198 10 *c 1.01,2.896 1.323,3.094 0.313,0.198 10 *b 0.448,2.094 0.906,2.292 0.458,0.198 10 RR- 1.406,2.094 1.865,2.292 0.458,0.198 10 RR+ 2.115,2.094 2.573,2.292 0.458,0.198 10 RR+ 2.771,2.094 3.229,2.292 0.458,0.198 10 RR- 0.417,4.417 0.875,4.615 0.458,0.198 10 RL- 1.469,4.427 1.927,4.625 0.458,0.198 10 RL+ 1.938,4.438 2.396,4.635 0.458,0.198 10 RL+ 2.885,4.427 3.344,4.625 0.458,0.198 10 RL-
*A for RH
*B for LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the h1 or i1 rear speed sensor connector and the skid control sensor wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
h1-2 (RR+) - hO1-1 (RR+) Always Below 1 Ω
h1-2 (RR+) - hO1-2 (RR-) Always 10 kΩ or higher
h1-2 (RR+) - Body ground Always 10 kΩ or higher
h1-1 (RR-) - hO1-2 (RR-) Always Below 1 Ω
h1-1 (RR-) - hO1-1 (RR+) Always 10 kΩ or higher
h1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
i1-2 (RL+) - iN1-1 (RL+) Always Below 1 Ω
i1-2 (RL+) - iN1-2 (RL-) Always 10 kΩ or higher
i1-2 (RL+) - Body ground Always 10 kΩ or higher
i1-1 (RL-) - iN1-2 (RL-) Always Below 1 Ω
i1-1 (RL-) - iN1-1 (RL+) Always 10 kΩ or higher
i1-1 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)

NG

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A28-22 (RR+) - hO1-1 (RR+) Always Below 1 Ω
A28-22 (RR+) - Body ground Always 10 kΩ or higher
A28-9 (RR-) - hO1-2 (RR-) Always Below 1 Ω
A28-9 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A28-20 (RL+) - iN1-1 (RL+) Always Below 1 Ω
A28-20 (RL+) - Body ground Always 10 kΩ or higher
A28-7 (RL-) - iN1-2 (RL-) Always Below 1 Ω
A28-7 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
C213978C11
0.271,1.031 0.677,1.292 0.406,0.26 1.708,1.031 2.115,1.292 0.406,0.26 1.198,2.01 1.354,2.521 false 2.604,2 2.865,2.521 false 0.323,0.25 0.708,0.573 0.385,0.323 10 false *a 1.219,2.563 1.688,2.854 0.469,0.292 10 false RR+ 2.719,2.542 3.146,2.854 0.427,0.313 10 false RL+ 0.354,1.073 0.813,1.344 0.458,0.271 10 false hO1 1.823,1.073 2.188,1.313 0.365,0.24 10 false iN1
*a Front view of wire harness connector
(to Skid Control Sensor Wire)


Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
hO1-1 (RR+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
iN1-1 (RL+) - Body ground Power switch on (IG) 5.7 to 14 V



Result:
Proceed to
OK
NG



OK

9.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.RECONFIRM DTC
a.

Turn the power switch off.


b.

Reconnect the h1 or i1 rear speed sensor connector and the skid control sensor wire.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the power switch on (READY).


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1466/33 and/or C1467/34 are output. A
DTCs C1466/33 and C1467/34 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
a.

Turn the power switch off.


b.

Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch on (READY).


c.

Perform a road test.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1466/33 and/or C1467/34 are output. A
DTCs C1466/33 and C1467/34 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

END