Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1202/68  Master Reservoir Level Malfunction  


DESCRIPTION

When a fluid level drop in the brake master cylinder reservoir assembly is detected, a signal is sent to the skid control ECU (brake booster with master cylinder assembly).

If a DTC for the fluid level drop is stored, the warning will be canceled and the DTC will be cleared when the fluid level returns to normal.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1202/68 Master Reservoir Level Malfunction 371
·

INF Code: 371

·

An open is detected in the switch signal circuit for 2 seconds or more.


·

INF Code: -

·

The reservoir level remains low.



·

INF Code: 371

·

Brake fluid level warning switch (Brake master cylinder reservoir assembly) internal open circuit


·

Open in wire harness


·

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: -

·

Low brake fluid level


·

Brake fluid leaks


·

Brake fluid level warning switch (Brake master cylinder reservoir assembly) internal short circuit


·

Short in wire harness


·

Brake disc rotor excessive wear


·

Skid control ECU (Brake booster with master cylinder assembly)



Electronically controlled brake system DTC

WIRING DIAGRAM

C269751E05
2.615,2.104 4.677,2.667 2.063,0.563 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 4.417,1.24 4.521,1.396 0.104,0.156 10 false 1 2.219,2.104 2.896,2.458 0.677,0.354 10 false A31 2.458,1.24 2.75,1.531 0.292,0.292 10 false 2 5.531,1.24 5.948,1.552 0.417,0.313 10 false 36 5.063,2.979 7.125,3.448 2.063,0.469 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.802,1.333 6.25,1.615 0.448,0.281 10 false LBL 4.677,2.979 5.073,3.313 0.396,0.333 10 false A28 4.188,1.24 4.385,1.469 0.198,0.229 10 false + 2.677,1.24 2.875,1.521 0.198,0.281 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


HINT:

Before releasing the parking brake, chock the wheels for safety.


PROCEDURE

1.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is sufficient.

OK:

Brake fluid level is sufficient.


HINT:

If the fluid level is low, check for fluid leaks, and repair as necessary.


i.

Check for brake fluid leaks (Connection between the brake booster pump assembly, brake master cylinder reservoir assembly and brake booster with master cylinder assembly, and the brake booster with master cylinder assembly and wheel cylinders).

HINT:

If no leaks exist, add and adjust fluid using the intelligent tester.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION



ii.

Check that the DTC is not output again.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105


b.

Check that there are no leaks from the connections between the brake booster pump assembly and brake booster with master cylinder assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

Bleed the air from the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the power switch on (IG).


iv.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor Min.: 0.00 V, Max.: 5.00 V Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Sensor
50003 105 13

v.

Wait for 30 seconds without depressing the brake pedal.


vi.

Check that the accumulator pressure sensor output value change is within the specified range.

OK:

Accumulator pressure sensor output value change is less than 0.55 V.




Result:
Proceed to
OK
NG



OK

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.
C213271C04
1.542,1.854 0.875,2.885 false 2,1.896 2.656,2.927 false 0.781,2.917 1.063,3.198 0.281,0.281 10 E 2.646,2.938 2.885,3.167 0.24,0.229 10 + 0.375,0.354 0.688,0.51 0.313,0.156 10 *a
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Turn the power switch off.


b.

Remove the reservoir filler cap.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the A31 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the level of brake fluid.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (E) Brake fluid level warning switch OFF (float up) 1.84 to 2.16 kΩ
1 (+) - 2 (E) Brake fluid level warning switch ON (float down) Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-36 (LBL) - A31-1 (+) Always Below 1 Ω
A28-36 (LBL) - Body ground Always 10 kΩ or higher
A31-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT SKID CONTROL ECU (SWITCH INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SKID CONTROL ECU (SWITCH INPUT)
a.
C156573C08
0.396,1.083 0.813,1.333 0.417,0.25 1.573,2.271 1.083,2.813 false 0.5,1.115 1.094,1.458 0.594,0.344 10 false A31 1,2.833 1.188,3.063 0.188,0.229 10 false + 0.24,0.25 0.719,0.542 0.479,0.292 10 false *a
*a Front view of wire harness connector
(to Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A31-1 (+) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK BRAKE DISC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK BRAKE DISC
a.

Turn the power switch off.


b.

Reconnect the A31 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


c.

Disconnect the A41 brake pedal stroke sensor assembly connector.


d.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper pistons and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

Uneven disc wear can be checked by measuring the disc thickness variation.

for Front: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION

for Rear: Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION




Result:
Proceed to
OK
NG



OK

6.RECONFIRM DTC

NG

REPLACE BRAKE DISC

6.RECONFIRM DTC
a.

Reconnect the A41 brake pedal stroke sensor assembly connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1202/68 is not output. A
DTC C1202/68 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY