The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there are any problems in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123/62 (Lost Communication with Yaw Rate Sensor Module) and U0124/95 (Lost Communication with Lateral Acceleration Sensor Module) will be stored.
These DTCs (C1210/36 and C1336/98) will also be stored when calibration has not been completed.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1210/36 | Zero Point Calibration of Yaw Rate Sensor Undone | - | Yaw rate sensor zero point calibration is incomplete. | ·
Zero point calibration undone ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
Skid control ECU (Brake booster with master cylinder assembly) (Perform zero point calibration and check for DTCs. If no DTCs are output again, the sensor is normal.) |
VSC DTC |
| C1336/98 | Zero Point Calibration of Acceleration Sensor Undone | - | Either of the following is detected:
1.
The vehicle is driven normally without zero point calibration completed. 2.
After completing zero point calibration, zero point voltage of the sensor is not within the range of 2.38 to 2.62 V. |
·
Zero point calibration undone ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
Skid control ECU (Brake booster with master cylinder assembly) (Perform zero point calibration and check for DTCs. If no DTCs are output again, the sensor is normal.) |
ABS DTC |
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION
When U0123/62 and/or U0124/95 is output together with C1210/36 and/or C1336/98, inspect and repair trouble areas indicated by U0123/62 and/or U0124/95 first.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94
Perform zero point calibration of the yaw rate and acceleration sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION
| Tester Display |
|---|
| Test Mode |
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch off.
Clear the DTCs.
Turn the power switch on (READY).
Drive the vehicle at a speed of 30 km/h (18 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C1210/36 and/or C1336/98 are output. | A |
| DTCs C1210/36 and C1336/98 are not output. | B |
The DTCs are recorded because zero point calibration has not been completed.
End the procedure if the same DTCs are not recorded after completion of zero point calibration.
A
B
Turn the power switch off.
Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
The sensor is tightened to the specified torque.
The sensor is not tilted.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
Replace the yaw rate and acceleration sensor (airbag sensor assembly).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
Check the yaw rate and acceleration sensor signal after replacement.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the power switch on (READY).
Drive the vehicle at a speed of 30 km/h (18 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C1210/36 and/or C1336/98 are output. | A |
| DTCs C1210/36 and C1336/98 are not output. | B |
A
B