Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1234/34  Yaw Rate Sensor Malfunction  C1243/43  Acceleration Sensor Stuck Malfunction  C1244/44  Open or Short in Acceleration Sensor Circuit  C1245/45  Acceleration Sensor Output Malfunction  C1279/79  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  C1381/97  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there are malfunctions in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123/62 (Lost Communication with Yaw Rate Sensor Module) and U0124/95 (Lost Communication with Lateral Acceleration Sensor Module) are stored.

These DTCs are also output when calibration has not been completed.

DTC C1279/79 will be cleared when the yaw rate and acceleration sensor (airbag sensor assembly) sends a yaw rate and/or acceleration signal or when Test Mode ends. DTC C1279/79 is output only in Test Mode.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1234/34 Yaw Rate Sensor Malfunction 711
712
713
714
·

INF Code: 711

·

While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 1 (GL1) malfunction).


·

INF Code: 712

·

While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 2 (GL2) malfunction).


·

INF Code: 713

·

While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Zero point calibration malfunction).


·

INF Code: 714

·

While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Two-value comparison malfunction).



Yaw rate and acceleration sensor (Airbag sensor assembly) internal malfunction VSC DTC
C1243/43 Acceleration Sensor Stuck Malfunction 561
562
563
564
565
·

INF Code: 561

·

An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h (19 mph) to 0 km/h (0 mph).


·

INF Code: 562, 563, 564, 565

·

A stuck acceleration sensor value is determined.



Yaw rate and acceleration sensor (Airbag sensor assembly) internal stuck malfunction ABS DTC
C1244/44 Open or Short in Acceleration Sensor Circuit 571 Either of the following is detected:
1.

Difference between GL1 and GL2 does not become less than 0.4 G for 60 seconds or more after reaching 0.6 G when the vehicle is stopped.

2.

A malfunction signal from the acceleration sensor is received.


·

Yaw rate and acceleration sensor (Airbag sensor assembly) installed improperly

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


ABS DTC
C1245/45 Acceleration Sensor Output Malfunction 581 Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Yaw rate and acceleration sensor (Airbag sensor assembly) installed improperly

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


ABS DTC
C1279/79 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC) - Detected only during Test Mode.
·

Sensor installation

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


ABS Test Mode DTC
C1381/97 Acceleration Sensor Power Supply Voltage Malfunction 601 While yaw rate and acceleration sensor communication is enabled, a supply voltage malfunction signal is received from the sensor for 10 seconds.
·

Yaw rate and acceleration sensor (Airbag sensor assembly) supply voltage shut down

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


ABS DTC

WIRING DIAGRAM

C246787E15
0.063,3.875 0.333,4.031 0.271,0.156 10 false I47 5.042,4.031 7.156,4.385 2.115,0.354 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 6.052,1.333 6.594,1.802 0.542,0.469 10 false CA1H 6.052,0.719 6.563,0.958 0.51,0.24 10 false CA1L 5.052,3.854 5.417,4.146 0.365,0.292 10 false A28 5.802,1.198 6.031,1.354 0.229,0.156 10 false 37 5.802,0.594 6.042,0.969 0.24,0.375 10 false 38 3.896,1.917 4.896,2.073 1,0.156 10 false from IG2 Relay 2.354,2.073 2.906,2.417 0.552,0.344 10 false A/B 1.281,1.813 1.479,1.979 0.198,0.167 10 false 21 1.281,1.198 1.479,1.365 0.198,0.167 10 false 13 1.281,0.594 1.458,0.76 0.177,0.167 10 false 22 0.781,1.302 1.208,1.448 0.427,0.146 10 false CANH 0.938,1.906 1.24,2.052 0.302,0.146 10 false IG2 1.01,2.531 1.24,2.677 0.229,0.146 10 false E1 0.792,0.677 1.219,0.823 0.427,0.146 10 false CANL 0.052,4.031 2.24,4.385 2.188,0.354 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 1.01,3.156 1.354,3.51 0.344,0.354 10 false E2 1.281,2.427 1.479,2.594 0.198,0.167 10 false 25 1.281,3.063 1.479,3.229 0.198,0.167 10 false 26 2.667,1.813 2.865,1.979 0.198,0.167 10 false 1 2.198,1.813 2.396,1.979 0.198,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION


HINT:

When U0123/62 and/or U0124/95 is output together with C1234/34, C1243/43, C1244/44, C1245/45, and/or C1381/97, inspect and repair the trouble areas indicated by U0123/62 and/or U0124/95 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Turn the power switch on (IG) again and check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


f.

Check if DTC C1210/36 (Zero Point Calibration of Yaw Rate Sensor Undone) or C1336/98 (Zero Point Calibration of Acceleration Sensor Undone) is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs (C1210/36, C1336/98 and CAN communication system DTC) are not output. A
CAN communication system DTC is output. B
DTCs C1210/36 and/or C1336/98 are output. C



A

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

C

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the power switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.
C239271C22
0.25,0.708 0.656,0.99 0.406,0.281 1.021,2.167 0.563,2.833 false 0.375,0.76 0.958,1.052 0.583,0.292 10 false I47 0.24,0.219 0.458,0.396 0.219,0.177 10 false *a 0.406,2.865 1.042,3.125 0.635,0.26 10 false IG2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the I47 yaw rate and acceleration sensor (airbag sensor assembly) connector.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I47-21 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (E TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (E TERMINAL)
a.
C239271C62
0.25,0.708 0.729,1 0.479,0.292 1.646,2.188 1.188,2.854 false 1.792,2.177 2.229,2.865 false 0.396,0.771 0.979,1.063 0.583,0.292 10 false I47 0.24,0.219 0.458,0.396 0.219,0.177 10 false *a 1.052,2.885 1.688,3.146 0.635,0.26 10 false E1 2.135,2.885 2.771,3.146 0.635,0.26 10 false E2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-25 (E1) - Body ground Always Below 1 Ω
I47-26 (E2) - Body ground Always Below 1 Ω


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (E CIRCUIT)