Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2015.04
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

Pressing the vehicle stability control switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF message will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C239016E23
1.385,0.813 1.729,1.073 0.344,0.26 10 false 16 1.396,1.615 1.708,1.813 0.313,0.198 10 false 17 0.917,0.927 1.531,1.156 0.615,0.229 10 false CANL 0.906,1.729 1.417,1.99 0.51,0.26 10 false CANH 0.146,3.948 0.458,4.146 0.313,0.198 10 false I18 0.417,3.948 1.615,4.365 1.198,0.417 10 false Combination Meter Assembly 3.781,2.771 4.094,2.969 0.313,0.198 10 false 6 4.833,2.771 5.146,2.969 0.313,0.198 10 false 9 3.948,2.979 4.26,3.177 0.313,0.198 10 false E 4.646,2.99 4.958,3.188 0.313,0.198 10 false + 3.583,3.24 3.896,3.438 0.313,0.198 10 false I170 3.573,3.417 5.083,3.802 1.51,0.385 10 false Vehicle Stability Control Switch 5.698,0.823 6.01,1.021 0.313,0.198 10 false 38 5.698,1.635 6.01,1.833 0.313,0.198 10 false 37 5.771,2.771 6.083,2.969 0.313,0.198 10 false 8 5.948,0.927 6.406,1.146 0.458,0.219 10 false CA1L 5.938,1.75 6.427,2.01 0.49,0.26 10 false CA1H 5.948,2.875 6.375,3.104 0.427,0.229 10 false CSW 5.094,3.75 5.406,3.948 0.313,0.198 10 false A28 5.083,3.938 7.156,4.354 2.073,0.417 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO SKID CONTROL ECU CORRECTLY

3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
Unknown: Unspecified
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

d.

Check the indicator light and mode condition on the intelligent tester change according to vehicle stability control switch operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display (TRC OFF Message) VSC OFF Indicator Light
Not pressed Normal Not displayed Does not come on
Pressing the vehicle stability control switch TRC OFF Displayed Does not come on
Pressing and holding the vehicle stability control switch VSC OFF Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display is normal. C



A

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MULTI-INFORMATION DISPLAY AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MULTI-INFORMATION DISPLAY AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light Multi-information display (TRC OFF message) Display ON/OFF Observe combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Chassis > ABS/VSC/TRC > Active Test
Tester Display
TRC(TRAC) OFF Indicator Light
50004 105 78
Chassis > ABS/VSC/TRC > Active Test
Tester Display
VSC OFF Indicator Light
50004 105 79

b.

Check the multi-information display (TRC OFF message) and VSC OFF indicator light on the combination meter assembly turns ON or OFF in accordance with intelligent tester operation.

OK:

The multi-information display (TRC OFF message) and VSC OFF indicator light turns on or off in accordance with intelligent tester operation.



Result:
Proceed to
OK
NG



OK

5.INSPECT VEHICLE STABILITY CONTROL SWITCH

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT VEHICLE STABILITY CONTROL SWITCH
a.
C311100C05
1.375,2.729 1.521,2.104 false 2.302,2.698 2.115,2.104 false 0.49,0.573 0.802,0.771 0.313,0.198 10 false *a 2.292,2.792 2.604,2.99 0.313,0.198 10 false E 1.302,2.781 1.615,2.979 0.313,0.198 10 false +
*a Component without harness connected
(Vehicle Stability Control Switch)


Turn the power switch off.


b.

Disconnect the I170 vehicle stability control switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (+) - 6 (E) Switch is pushed Below 1 Ω
9 (+) - 6 (E) Switch is not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - VEHICLE STABILITY CONTROL SWITCH)

NG

REPLACE VEHICLE STABILITY CONTROL SWITCH

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - VEHICLE STABILITY CONTROL SWITCH)
a.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-8 (CSW) - I170-9 (+) Always Below 1 Ω
A28-8 (CSW) - Body ground Always 10 kΩ or higher
I170-6 (E) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the power switch off.


b.

Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94

c.

Check the combination meter assembly.

OK:

The multi-information display and VSC OFF indicator light turns on or off in accordance with intelligent tester operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG