Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2015.04
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM T

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  PROBLEM SYMPTOMS TABLE  


If there are no DTCs but the problem still occurs, check the suspected areas for each problem symptom in the order given in the table below and proceed to the relevant troubleshooting page.

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), sensors, etc., make sure that the power switch is turned off, the stop light switch assembly is off, and 2 minutes have elapsed since the driver door was closed.


HINT:
·

Since the hydraulic passage is blocked off by the master cut solenoid during electronically controlled brake system control, there is no kickback (vibration) to the brake pedal, creating a quiet even while the ABS is operating.

·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Electronically Controlled Brake System
Symptom Suspected Area Link
ABS, BA and/or EBD does not operate Use a chassis dynamometer, etc. to check the electronically controlled brake system operation. -
Check again to see if DTCs are output. (If DTCs are output, perform diagnosis based on the DTCs that are output.) Click here
Power source circuit Click here
Front speed sensor circuit Click here
Rear speed sensor circuit Click here
Check the brake actuator (brake booster with master cylinder assembly) using the intelligent tester. (Check brake actuator (brake booster with master cylinder assembly) operation using the Active Test function.) If abnormal, check the hydraulic circuit for leaks. Click here
If the symptoms still occur even after the above suspected areas have been inspected and proved to be normal, replace the skid control ECU (brake booster with master cylinder assembly). Click here
ABS, BA and/or EBD does not operate efficiently Check again to see if DTCs are output. (If DTCs are output, perform diagnosis based on the DTCs that are output.) Click here
Front speed sensor circuit Click here
Rear speed sensor circuit Click here
Check the brake actuator (brake booster with master cylinder assembly) using the intelligent tester. (Check brake actuator (brake booster with master cylinder assembly) operation using the Active Test function.) If abnormal, check the hydraulic circuit for leaks. Click here
If the symptoms still occur even after the above suspected areas have been inspected and proved to be normal, replace the skid control ECU (brake booster with master cylinder assembly). Click here
ABS warning light abnormal (Remains on) ABS warning light circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
ABS warning light abnormal (Does not come on) ABS warning light circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
Brake warning light / red (malfunction) abnormal (Remains on) Brake fluid level warning switch circuit Click here
Brake warning light / red (malfunction) circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
Brake warning light / red (malfunction) abnormal (Does not come on) Brake warning light / red (malfunction) circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
VSC and/or TRC does not operate Use a chassis dynamometer, etc. to check the electronically controlled brake system operation. -
Check again to see if DTCs are output. (If DTCs are output, perform diagnosis based on the DTCs that are output.) Click here
Power source circuit Click here
Check the hydraulic circuit for leaks. -
Front speed sensor circuit Click here
Rear speed sensor circuit Click here
Yaw rate and acceleration sensor circuit Click here
Steering angle sensor circuit Click here
If the symptoms still occur even after the above suspected areas have been inspected and proved to be normal, replace the skid control ECU (brake booster with master cylinder assembly). Click here
Brake warning light / yellow (minor malfunction) abnormal (Remains on) Brake warning light / yellow (minor malfunction) circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
Brake warning light / yellow (minor malfunction) abnormal (Does not come on) Brake warning light / yellow (minor malfunction) circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
Vehicle stability control switch abnormal Vehicle stability control switch circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
Slip indicator light abnormal (Remains on) Slip indicator light circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
Slip indicator light abnormal (Does not come on) Slip indicator light circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
DTC check cannot be done Check again to see if DTCs are output. (If DTCs are output, perform diagnosis based on the DTCs that are output.) Click here
TC and CG terminal circuit Click here
If the symptoms still occur even after the above suspected areas have been inspected and proved to be normal, replace the skid control ECU (brake booster with master cylinder assembly). Click here
Sensor check cannot be done TS and CG terminal circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here
Meter buzzer abnormal Meter buzzer circuit Click here
Skid control ECU (Brake booster with master cylinder assembly) Click here