Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074886 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A82-123  Hybrid Battery Pack Cooling Fan 1 Performance / Stuck OFF  


DESCRIPTION

Refer to the description for DTC P0A84-123.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A84-123

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A82-123 Hybrid Battery Pack Cooling Fan 1 Performance / Stuck OFF The speed of the battery cooling blower assembly is not within the specified range (1 trip detection)
·

Battery cooling blower assembly

·

Battery smart unit

·

Power management control ECU

·

No. 1 hybrid battery intake duct

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A84-123.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A84-123

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.CHECK DUCT AND BLOWER

B

2.CHECK DUCT AND BLOWER
a.
A338265C02
2.938,0.208 2.823,0.208 2.823,0.208 2.396,0.542 true 3,0.135 3.313,0.333 0.313,0.198 10 false *1
*1 No. 1 Hybrid Battery Intake Duct


Check that the No. 1 hybrid battery intake duct and battery cooling blower assembly are not disconnected, damaged, or clogged with foreign matter, and that the acoustical materials have not peeled.

OK:

The duct and blower are not disconnected, damaged, or clogged with foreign matter and the acoustical materials have not peeled.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATTERY SMART UNIT)

NG

CORRECT THE PROBLEM

3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATTERY SMART UNIT)

OK

4.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - POWER MANAGEMENT CONTROL ECU)

OK

5.CHECK POWER MANAGEMENT CONTROL ECU (GROUND SHORT CHECK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER MANAGEMENT CONTROL ECU (GROUND SHORT CHECK)
a.

Remove the power management control ECU.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL


b.
A333634C01
1.969,1.708 2.219,1.917 0.25,0.208 2.552,1.708 2.802,1.917 0.25,0.208 2.885,0.385 2.781,0.385 2.781,0.385 2.573,1.01 true 1.521,0.396 1.615,0.396 1.615,0.396 1.885,1.01 true 2.292,1.156 2.229,0.375 2.229,0.375 2.135,0.375 true 2.042,1.75 2.354,1.948 0.313,0.198 10 false I3 2.635,1.75 2.948,1.948 0.313,0.198 10 false I4 2.948,0.323 3.26,0.521 0.313,0.198 10 false E02 1.25,0.323 1.563,0.521 0.313,0.198 10 false E01 0.104,0.313 0.417,0.51 0.313,0.198 10 false *a 1.896,0.313 2.208,0.51 0.313,0.198 10 false SI0
*a Component without harness connected
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Specified Condition
I3-17 (SI0) - I3-5 (E01) 10 kΩ or higher
I3-17 (SI0) - I4-5 (E02) 10 kΩ or higher



c.

Install the power management control ECU.

Result:
Proceed to
OK
NG




OK

6.READ VALUE USING INTELLIGENT TESTER (COOLING FAN FREQUENCY)

NG

6.READ VALUE USING INTELLIGENT TESTER (COOLING FAN FREQUENCY)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A84-123

Result:
Result Proceed to
The value in the Data List (Cooling Fan Frequency1) and the actual measured value at the battery cooling blower assembly connector are 0 Hz. A
Other than above B



A

7.CHECK BATTERY SMART UNIT

B

8.CHECK BATTERY SMART UNIT (FREQUENCY)
7.CHECK BATTERY SMART UNIT

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

8.CHECK BATTERY SMART UNIT (FREQUENCY)
a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the intelligent tester to the DLC3.


e.

Turn the power switch on (IG).

NOTICE:
·

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

·

If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR




f.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display
Driving the Battery Cooling Fan
50004 236 10
NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check voltage. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.



g.

Enter the following menus: All Data / Cooling Fan Frequency1.

Powertrain > Hybrid Control > Data List
Tester Display
Cooling Fan Frequency1
50003 236 1283

h.

Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.


i.
A244310C06
0.781,0.198 1.208,0.458 0.427,0.26 2.073,0.958 1.667,0.698 true 1.76,1.354 2.104,1.24 true 0.094,0.063 0.406,0.313 0.313,0.25 10 false *a 1.385,0.635 1.875,0.885 0.49,0.25 10 false FP0 1.375,1.302 1.823,1.552 0.448,0.25 10 false GND0 0.938,0.26 1.167,0.406 0.229,0.146 10 false r1 1.365,0.26 1.719,0.51 0.354,0.25 10 false *b
*a Component with harness connected
(Battery Cooling Blower Assembly)
*b Rear view of wire harness connector
(to Battery Cooling Blower Assembly)


While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency1) with the frequency value that was actually measured at the battery cooling blower assembly connector.

Standard:
Tester Connection Condition Specified Condition
r1-2 (FP0) - r1-4 (GND0) Battery cooling blower assembly is operating Difference between the value in the Data List (Cooling Fan Frequency1) and the actual measurement value is 10% or less.


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.



j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.


l.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG