Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074886 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A84-123  Hybrid Battery Pack Cooling Fan 1 Control Circuit Low  


DESCRIPTION

The speed of the battery cooling blower assembly is controlled by the power management control ECU. Power is supplied to the battery cooling blower assembly when the MREL terminal of the power management control ECU turns on the IGCT relay. The power management control ECU sends command signals (SI) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the HV battery temperature. The battery cooling blower assembly frequency (FP) is sent to the power management control ECU via the battery smart unit as a monitor signal using serial communication.

A260101E13
0.49,0.094 2.563,0.531 2.073,0.438 10 false Battery Cooling Blower Assembly 2.792,0.958 3.875,1.271 1.083,0.313 10 false Command Signal 2.896,3.198 3.896,3.427 1,0.229 10 false Monitor Signal 4.708,0.438 5.948,0.823 1.24,0.385 10 false Power Management Control ECU 4.76,2.74 5.958,3.042 1.198,0.302 10 false Battery Smart Unit 3.896,1.729 5.281,2.01 1.385,0.281 10 false Serial Communication

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A84-123 Hybrid Battery Pack Cooling Fan 1 Control Circuit Low When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target control speed range (1 trip detection)
·

Wire harness or connector

·

BATT FAN fuse

·

Battery cooling blower assembly

·

Battery smart unit

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A260746E12
5.865,4.792 7.094,5.156 1.229,0.365 10 false Power Management Control ECU 3.469,4.083 4.729,4.26 1.26,0.177 10 false Battery Smart Unit 4,3.323 4.365,3.552 0.365,0.229 10 false BTH+ 6.104,3.333 6.51,3.563 0.406,0.229 10 false BTH+ 2.104,1.115 2.813,1.375 0.708,0.26 10 false BATT FAN 4.083,3.01 4.385,3.24 0.302,0.229 10 false FP0 3.281,1.229 3.469,1.396 0.188,0.167 10 false 1 3.281,1.688 3.469,1.833 0.188,0.146 10 false 4 4.49,1.219 4.677,1.385 0.188,0.167 10 false 3 4.49,1.677 4.677,1.823 0.188,0.146 10 false 2 4.51,2.896 4.698,3.042 0.188,0.146 10 false 5 5.802,1.354 6.104,1.5 0.302,0.146 10 false I3 5.792,1.146 6.042,1.292 0.25,0.146 10 false 17 5.813,0.406 6.104,0.552 0.292,0.146 10 false 4 4.021,3.635 4.396,3.885 0.375,0.25 10 false BTH- 3.156,4.094 3.438,4.396 0.281,0.302 10 false N18 3.229,2.146 3.375,2.448 0.146,0.302 10 false r1 6.104,3.656 6.479,3.875 0.375,0.219 10 false BTH- 6.094,0.583 6.542,0.865 0.448,0.281 10 false MREL 5.771,3.156 6.063,3.396 0.292,0.24 10 false 30 4.51,3.552 4.76,3.698 0.25,0.146 10 false 4 3.458,2.146 4.885,2.698 1.427,0.552 10 false Battery Cooling Blower Assembly 6.104,1.313 6.385,1.531 0.281,0.219 10 false Sl0 6.104,4.375 6.396,4.656 0.292,0.281 10 false E02 6.104,4.01 6.51,4.271 0.406,0.26 10 false E01 5.74,0.615 6.01,0.813 0.271,0.198 10 false A38 5.813,4.188 6.042,4.354 0.229,0.167 10 false 5 4.5,3.219 4.75,3.365 0.25,0.146 10 false 1 4.073,1.792 4.354,2.021 0.281,0.229 10 false FP0 4.104,1.354 4.385,1.667 0.281,0.313 10 false Sl0 3.521,1.354 3.813,1.594 0.292,0.24 10 false IG0 3.51,1.792 3.917,2.063 0.406,0.271 10 false GND0 5.792,3.323 6.052,3.49 0.26,0.167 10 false I3 5.802,3.667 6.052,3.813 0.25,0.146 10 false I3 5.771,3.49 6.083,3.698 0.313,0.208 10 false 29 5.802,4.375 6.052,4.521 0.25,0.146 10 false I4 5.802,3.833 6.031,4 0.229,0.167 10 false 5 5.792,4.01 6.042,4.156 0.25,0.146 10 false I3 1.01,4.229 2.115,4.625 1.104,0.396 10 false Auxiliary Battery 0.875,2.063 1.719,2.417 0.844,0.354 10 false IGCT-MAIN 0.896,2.625 1.552,2.99 0.656,0.365 10 false R/B NO. 2 1.219,1.271 1.583,1.531 0.365,0.26 10 false IGCT 1.771,0.49 1.958,0.656 0.188,0.167 10 false 1 0.927,0.49 1.115,0.635 0.188,0.146 10 false 2 0.927,0.823 1.115,0.99 0.188,0.167 10 false 3 1.771,0.833 2,1 0.229,0.167 10 false 5 2.177,0.802 2.365,0.969 0.188,0.167 10 false 1 2.594,0.802 2.781,0.969 0.188,0.167 10 false 2 0.896,3.146 1.396,3.479 0.5,0.333 10 false MAIN 0.604,2.25 0.792,2.417 0.188,0.167 10 false 1 0.615,1.854 0.802,2.021 0.188,0.167 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check fan operates and air is sucked. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.


Powertrain > Hybrid Control > Active Test
Tester Display
Driving the Battery Cooling Fan
50004 236 10

d.

Select air volume mode 6 in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.


e.

Check that the fan operates and air is sucked into the inlet duct.

HINT:

The cooling fan may not stop even when turning the cooling fan off in the "Driving the Battery Cooling Fan" Active Test. This is due to HV system control and not a malfunction.


OK:

The fan operates.



f.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATTERY SMART UNIT)

NG

7.CHECK FUSE (BATT FAN)
3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATTERY SMART UNIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Remove the rear side seatback assembly LH.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


d.

Disconnect connector r1 from the battery cooling blower assembly.


e.

Disconnect connector N18 from the battery smart unit.


f.
A259921C05
0.802,0.573 1.229,0.833 0.427,0.26 0.396,3.177 0.823,3.479 0.427,0.302 1.813,0.792 2.313,0.542 true 1.188,3.667 1.646,4.104 true 2.417,0.448 2.688,0.708 0.271,0.26 10 false FP0 0.729,0.125 1.063,0.365 0.333,0.24 10 false *a 1.042,1.563 1.375,1.802 0.333,0.24 10 false *b 1.698,4.031 1.969,4.292 0.271,0.26 10 false FP0 0.938,0.625 1.167,0.771 0.229,0.146 10 false r1 0.51,3.24 0.802,3.448 0.292,0.208 10 false N18
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
*b Rear view of wire harness connector
(to Battery Smart Unit)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
r1-2 (FP0) - N18-5 (FP0) Power switch off Below 1 Ω
r1-2 (FP0) or N18-5 (FP0) - Body ground Power switch off 10 kΩ or higher



g.

Connect the battery cooling blower assembly connector.


h.

Connect the battery smart unit connector.


i.

Install the rear side seatback assembly LH.


j.

Install the luggage compartment front trim cover.

Result:
Proceed to
OK
NG




OK

4.READ VALUE USING INTELLIGENT TESTER (COOLING FAN FREQUENCY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATTERY SMART UNIT)

4.READ VALUE USING INTELLIGENT TESTER (COOLING FAN FREQUENCY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the intelligent tester to the DLC3.


e.

Turn the power switch on (IG).

NOTICE:
·

After removing the service plug grip, do not turn the power switch on (READY) unless instructed by the repair manual because this may cause a malfunction.

·

If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR




f.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


g.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 236
NOTICE:

When DTCs are cleared, freeze frame data and INF codes are also cleared.



h.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display
Driving the Battery Cooling Fan
50004 236 10
NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check voltage. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.



i.

Enter the following menus: Powertrain / Hybrid Control / Data List / Cooling Fan Frequency1.

Powertrain > Hybrid Control > Data List
Tester Display
Cooling Fan Frequency1
50003 236 1283

j.

Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.


k.
A244310C09
0.781,0.198 1.208,0.458 0.427,0.26 2.073,0.958 1.667,0.698 true 1.76,1.354 2.104,1.24 true 0.094,0.063 0.406,0.313 0.313,0.25 10 false *a 1.385,0.635 1.875,0.885 0.49,0.25 10 false FP0 1.375,1.302 1.823,1.552 0.448,0.25 10 false GND0 0.938,0.26 1.167,0.406 0.229,0.146 10 false r1 1.365,0.26 1.719,0.51 0.354,0.25 10 false *b
*a Component with harness connected
(Battery Cooling Blower Assembly)
*b Rear view of battery cooling blower assembly connector
(to Wire Harness Connector)


While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency1) with the frequency value that was actually measured at the battery cooling blower assembly connector.

Specified Condition:
Tester Connection Condition
r1-2 (FP0) - r1-4 (GND0) Battery cooling blower assembly is operating


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.



Result:
Result Proceed to
The value in the Data List (Cooling Fan Frequency1) and the actual measured value at the battery cooling blower assembly connector are 0 Hz. A
Other than above B


l.

Turn the power switch off.


m.

Disconnect the cable from the negative (-) auxiliary battery terminal.


n.

Install the luggage compartment front trim cover.



A

5.CHECK BATTERY SMART UNIT

B

6.CHECK BATTERY SMART UNIT (FREQUENCY)
5.CHECK BATTERY SMART UNIT
a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Disconnect the r1 battery cooling blower assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).

NOTICE:
·

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

·

If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the GTS.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR




f.
A366610C23
2.25,0.979 2.688,1.229 0.438,0.25 0.813,0.521 1.573,0.938 false 0.885,1.625 1.594,1.281 false 2.354,1.01 2.844,1.365 0.49,0.354 10 false r1 0.51,0.438 1,0.792 0.49,0.354 10 false FP0 0.521,1.625 1.01,1.979 0.49,0.354 10 false GND0 0.083,0.042 0.573,0.396 0.49,0.354 10 false *a
*a Rear view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
r1-2 (FP0) - r1-4 (GND0) Power switch on (IG) 4.5 to 5.5 V



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the r1 battery cooling blower assembly connector.


j.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

6.CHECK BATTERY SMART UNIT (FREQUENCY)

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

7.CHECK FUSE (BATT FAN)
a.

Remove the BATT FAN fuse from the No. 2 engine room relay block.


b.
A260088C04
0.202,0.134 0.407,0.325 0.205,0.191 10 *1 1.723,1.643 2.496,1.775 false 2.539,1.689 2.744,1.88 0.205,0.191 10 *2
*1 No. 2 Engine Room Relay Block
*2 BATT FAN Fuse


Measure the resistance of the BATT FAN fuse.

Standard Resistance:
Tester Connection Condition Specified Condition
BATT FAN fuse Always Below 1 Ω



c.

Install the BATT FAN fuse to the No. 2 engine room relay block.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (VOLTAGE)

NG

14.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (VOLTAGE)
a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the intelligent tester to the DLC3.


e.

Turn the power switch on (IG).

NOTICE:
·

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

·

If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR




f.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


g.

Clear DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 236
NOTICE:

When DTCs are cleared, freeze frame data and INF codes are also cleared.



h.
A244310C07
0.781,0.292 1.208,0.615 0.427,0.323 2.323,1.01 2.729,0.74 true 0.167,0.135 0.521,0.385 0.354,0.25 10 false *a 2.781,0.656 3.094,0.865 0.313,0.208 10 false IG0 0.938,0.344 1.167,0.49 0.229,0.146 10 false r1 1.417,0.302 1.771,0.552 0.354,0.25 10 false *b
*a Component with harness connected
(Battery Cooling Blower Assembly)
*b Rear view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
r1-1 (IG0) - Body ground Battery cooling blower is operating 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Measure the voltage on the wire side of the connector that is part of the battery cooling blower.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

NG

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Disconnect connector r1 from the battery cooling blower assembly.


d.

Disconnect connector I3 from the power management control ECU.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL


e.
A333635C01
2.354,1.01 2.625,1.219 0.271,0.208 1.208,3.698 1.479,3.906 0.271,0.208 1.031,1.479 1.604,1.292 true 2.271,3.875 2.583,4.021 true 0.792,1.427 1.25,1.625 0.458,0.198 10 false SI0 0.958,0.323 1.417,0.521 0.458,0.198 10 false *a 0.146,2.198 0.604,2.396 0.458,0.198 10 false *b 2.448,1.052 2.906,1.25 0.458,0.198 10 false r1 1.302,3.74 1.76,3.938 0.458,0.198 10 false I3 2.646,3.969 3.104,4.167 0.458,0.198 10 false SI0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
*b Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
r1-3 (SI0) - I3-17 (SI0) Power switch off Below 1 Ω
r1-3 (SI0) or I3-17 (SI0) - Body ground Power switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r1-3 (SI0) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the battery cooling blower assembly connector and power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Connect the battery cooling blower assembly connector.


l.

Install the luggage compartment front trim cover.


m.

Connect the power management control ECU connector.


Result:
Proceed to
OK
NG



OK

10.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK BATTERY COOLING BLOWER ASSEMBLY
a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the intelligent tester to the DLC3.


e.

Turn the power switch on (IG).

NOTICE:
·

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

·

If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR




f.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


g.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 236
NOTICE:

When DTCs are cleared, freeze frame data and INF codes are also cleared.



h.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

Powertrain > Hybrid Control > Active Test
Tester Display
Driving the Battery Cooling Fan
50004 236 10

i.

Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling blower assembly.



j.
A244310C10
0.781,0.198 1.208,0.458 0.427,0.26 2.74,1.469 2.333,1.208 true 1.792,1.469 2.104,1.24 true 0.094,0.063 0.406,0.313 0.313,0.25 10 false *a 2.833,1.448 3.417,1.854 0.583,0.406 10 false SI0 1.417,1.469 1.865,1.719 0.448,0.25 10 false GND0 0.938,0.26 1.167,0.406 0.229,0.146 10 false r1 1.365,0.26 1.719,0.51 0.354,0.25 10 false *b
*a Component with harness connected
(Battery Cooling Blower Assembly)
*b Rear view of wire harness connector
(to Battery Cooling Blower Assembly)


Connect an oscilloscope to the r1 battery cooling blower assembly connector and check the waveform.

Item Content
Tester Connection r1-3 (SI0) - r1-4(GND0)
Equipment Setting 10 V/DIV., 1 ms/DIV.
Condition Power switch on (IG) during Active Test

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:
·

Perform this inspection with the battery cooling blower assembly connector connected.

·

The wave length will vary with the operating speed of the battery cooling blower assembly.




k.

Turn the power switch off.


l.

Disconnect the cable from the negative (-) auxiliary battery terminal.


m.
A284431C01
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a
*a Waveform 1


Install the luggage compartment front trim cover.


Result:
Result Proceed to
Normal (The pulse output of waveform 1) A
No pulse generation B



A

REPLACE BATTERY COOLING BLOWER ASSEMBLY

B

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
a.

Disconnect connector I3 from the power management control ECU.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL


b.
A212482C22
2.427,2.51 2.813,2.771 0.385,0.26 1.875,2.656 1.323,2.958 true 0.146,0.677 0.573,0.969 0.427,0.292 10 false *a 2.542,2.563 2.854,2.823 0.313,0.26 10 false I3 1.042,2.906 1.365,3.198 0.323,0.292 10 false E01
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I3-5 (E01) - Body ground Power switch off Below 1 Ω


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Connect the power management control ECU connector.


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
a.

Disconnect connector I4 from the power management control ECU.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL


b.
A212483C18
2.969,2.333 3.313,2.625 0.344,0.292 2.51,2.479 1.677,2.729 true 0.198,0.542 0.615,0.792 0.417,0.25 10 false *a 3.094,2.365 3.292,2.552 0.198,0.188 10 false I4 1.385,2.677 1.75,2.896 0.365,0.219 10 false E02
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I4-5 (E02) - Body ground Power switch off Below 1 Ω


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



c.

Connect the power management control ECU connector.


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)
a.

Remove the IGCT relay from the No. 2 engine room relay block.


b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Disconnect connector r1 from the battery cooling blower assembly.


d.
A260747C11
2.448,0.792 2.781,1.031 0.333,0.24 1.563,1.156 1.01,0.948 true 0.375,0.198 0.667,0.458 0.292,0.26 10 false *a 0.771,0.854 1.052,1.104 0.281,0.25 10 false IG0 0.281,2.156 0.479,2.417 0.198,0.26 10 false *1 2.552,0.833 2.75,1.073 0.198,0.24 10 false r1 2.448,2.479 2.646,2.74 0.198,0.26 10 false *b
*1 No. 2 Engine Room Relay Block
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
*b IGCT Relay Block


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (IGCT relay block) - r1-1 (IG0) Power switch off Below 1 Ω



e.

Connect the battery cooling blower assembly connector.


f.

Install the luggage compartment front trim cover.


g.

Install the IGCT relay to the No. 2 engine room relay block.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)
a.

Remove the BATT FAN fuse from the No. 2 engine room relay block.


b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Disconnect connector r1 from the battery cooling blower assembly.


d.
A260099C10
2.396,0.667 2.823,0.927 0.427,0.26 1.552,1.01 1,0.792 true 0.365,0.094 0.604,0.354 0.24,0.26 10 false *a 0.75,0.708 1.031,0.958 0.281,0.25 10 false IG0 0.5,1.896 0.75,2.156 0.25,0.26 10 false *1 2.563,0.708 2.75,0.896 0.188,0.188 10 false r1 1.313,3.833 1.51,4.094 0.198,0.26 10 false *b
*1 No. 2 Engine Room Relay Block
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
*b BATT FAN Fuse Block


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
r1-1 (IG0) - Terminals other than 2 (BATT FAN fuse block) and body ground Power switch off 10 kΩ or higher



e.

Connect the battery cooling blower assembly connector.


f.

Install the luggage compartment front trim cover.


g.

Install the BATT FAN fuse to the No. 2 engine room relay block.


Result:
Proceed to
OK
NG



OK

15.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.CHECK BATTERY COOLING BLOWER ASSEMBLY
a.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


b.

Disconnect connector r1 from the battery cooling blower assembly.


c.
A221313C18
0.625,0.625 1.042,0.927 0.417,0.302 1.781,1.104 2.531,0.771 true 1.51,1.323 0.906,1.604 true 0.354,0.083 0.625,0.365 0.271,0.281 10 false *a 0.771,0.667 0.979,0.865 0.208,0.198 10 false r1 2.604,0.667 3.042,1.063 0.438,0.396 10 false IG0 0.5,1.531 1.01,1.875 0.51,0.344 10 false GND0
*a Component without harness connected
(Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
r1-1 (IG0) - r1-4 (GND0) and body ground Power switch off 10 kΩ or higher



d.

Connect the battery cooling blower assembly connector.


e.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (BATT FAN)

NG

16.REPLACE BATTERY COOLING BLOWER ASSEMBLY
16.REPLACE BATTERY COOLING BLOWER ASSEMBLY

NEXT

REPLACE FUSE (BATT FAN)

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (BATT FAN)