Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY › from 2015.04
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075084 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 89170 1.INSTALL AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B289049C03
2.063,1.156 2.26,1.406 2.26,1.406 2.396,1.406 false 2.51,0.448 2.729,0.677 0.219,0.229 10 false *a 2.427,1.323 2.865,1.625 0.438,0.302 10 false SST
*a Fulcrum Length


Using SST, install the airbag sensor assembly with the 3 bolts.

SST
09961-00950  

Torque:
without SST : 18 N*m (178 kgf*cm, 13 ft.*lbf)
with SST : 11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:
·

Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

·

This torque value is effective when SST is parallel to a torque wrench.

·

If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

When the power switch is first turned on (IG) after the airbag sensor assembly has been replaced, make sure that no one is in the vehicle.




d.
B289050C03
0.938,1.625 0.854,1.885 0.854,1.885 0.469,1.885 false 0.281,1.792 0.583,2.052 0.302,0.26 10 false *1
*1 Waterproof Sheet


Connect the connectors to the airbag sensor assembly as shown in the illustration.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



e.

Check that the waterproof sheet is properly set.


f.

Check that there is no looseness in the installation parts of the airbag sensor assembly.


Hide 58861B 2.INSTALL NO. 1 CONSOLE BOX DUCT

Hide 58543B 3.INSTALL FLOOR CARPET BRACKET RH

Hide 58544A 4.INSTALL FLOOR CARPET BRACKET LH

Hide 58817A 6.INSTALL FRONT NO. 2 CONSOLE BOX INSERT

Hide 58804A 7.INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

Hide 9.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 53601 10.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55317A 11.INSTALL INSTRUMENT SIDE PANEL RH

Hide 62311B 12.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62111A 13.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

Hide 67913 14.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 55303B 15.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 55607 16.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55318C 17.INSTALL INSTRUMENT SIDE PANEL LH

Hide 62312B 18.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62112A 19.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

HINT:

Use the same procedure for the LH side and RH side (Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).


Hide 67914 20.INSTALL FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure for the LH side and RH side (Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).


Hide 21.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 22.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 64718C 23.INSTALL LUGGAGE TRIM SERVICE HOLE COVER

Hide 26. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION

HINT:
·

When the airbag sensor assembly is replaced, perform zero point learning for the yaw rate and acceleration sensor (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).

·

The yaw rate and acceleration sensor is built into the airbag sensor assembly.