Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2015.04
RM2040EQ _59 Vehicle Exterior _014735 DOOR / HATCH _0075152 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the RH side.



PROCEDURE

Hide 75977H 2.INSTALL REAR DOOR LOWER OUTSIDE STRIPE

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Rear Door)>INSTALLATION


Hide 75987F 3.INSTALL REAR DOOR OUTSIDE STRIPE

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Rear Door)>INSTALLATION


Hide 4.INSTALL NO. 2 BLACK OUT TAPE

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Rear Door)>INSTALLATION


Hide 5.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR WINDOW FRAME MOULDING>INSTALLATION


Hide 75763A 6.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR WINDOW FRAME MOULDING>INSTALLATION


Hide 75761A 7.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR WINDOW FRAME MOULDING>INSTALLATION


Hide 75730 8.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>INSTALLATION


Hide 67003C 9.INSTALL REAR DOOR PANEL CUSHION

a.
B287014

Engage the 2 claws to install 2 new rear door panel cushions.


Hide 67887H 10.INSTALL REAR DOOR NO. 2 WEATHERSTRIP

a.
B287013

Engage the 5 clips to install the rear door No. 2 weatherstrip.


Hide 69203A 11.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B307970C01
2.75,1.531 3.125,1.458 false 0.052,0.052 0.219,0.229 0.167,0.177 10 false *a 0.052,2.094 0.219,2.271 0.167,0.177 10 false *b 3.115,1.344 3.271,1.51 0.156,0.167 10 false *1
*1 Door Handle Nut
*a Outside
*b Inside


Engage the claw.


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw and door handle nut.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 12.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B307968

Engage the 2 claws to install the rear door rear outside handle pad.


Hide 69241G 13.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B307967

Engage the 3 claws to install the rear door front outside handle pad.


Hide 69230 14.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B307971

Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

NOTICE:

If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.



b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.


Hide 69250F 15.INSTALL REAR DOOR OUTSIDE HANDLE COVER ASSEMBLY

a.
B307965

Engage the claw and install the rear door outside handle cover assembly.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69770B 16.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B287017

Install the rear door inside locking cable assembly.


b.
B287018

Engage the 3 claws.


Hide 69730D 17.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B287019

Install the rear door lock remote control cable assembly.


b.
B287020

Engage the claw.


Hide 69050A 18.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing the removed rear door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door with motor lock assembly.



a.

Apply MP grease to the sliding parts of the rear door lock with motor assembly.


b.

When reusing the rear door with motor lock assembly:

i.
B287001

Install a new door lock wiring harness seal to the rear door lock with motor assembly.



c.
B291308C02
0.313,2.885 0.49,2.823 false 0.156,2.802 0.323,2.979 0.167,0.177 10 false *1
*1 Release Plate


Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.


d.

Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.


e.

Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 85710F 19.INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.


a.
B286999

Using a T25 "TORX" socket wrench, install the rear power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

When replacing the rear window regulator, a new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



Hide 20.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.

Install the temporary bolt to the rear door window regulator assembly.


c.
B286998C04
2.438,0.313 1.573,0.49 true 1.01,1.271 0.396,1.438 true 0.583,1.031 0.219,1.073 true 0.552,0.521 0.281,0.563 true 2.458,0.208 2.615,0.365 0.156,0.156 10 false *1 0.198,1.344 0.427,1.51 0.229,0.167 10 false (1) 0.052,0.979 0.281,1.146 0.229,0.167 10 false (3) 0.073,0.479 0.302,0.646 0.229,0.167 10 false (2) 2.625,0.208 2.854,0.375 0.229,0.167 10 false (4)
*1 Temporary Bolt


Temporarily install the rear door window regulator assembly.


d.

Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



Hide 67673A 21.INSTALL REAR DOOR FRAME GARNISH

a.
B287012

Engage the clip to install a new rear door frame garnish.


Hide 69975A 22.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.

Apply soapy water to a new rear door glass channel filler.


b.
B287022C03
1.063,1.135 0.667,0.99 false 2.667,1.146 3.115,1 false 0.615,0.229 0.813,0.375 0.198,0.146 10 false *B 2.521,0.229 2.719,0.375 0.198,0.146 10 false *A 0.969,0.542 1.354,0.833 0.385,0.292 10 false *b 3.146,0.885 3.344,1.031 0.198,0.146 10 false *c 0.458,0.885 0.656,1.031 0.198,0.146 10 false *c 2.594,0.542 2.99,0.854 0.396,0.313 10 false *a
*A Front Side
*B Rear Side
*a 4.57 mm (0.180 in.)
*b 4.8 mm (0.189 in.)
*c Edge of curved surface


Install the rear door glass channel filler to the position shown in the illustration.


Hide 69905B 23.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY

a.

Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.


b.
B287023C03
2.646,1.135 3.031,0.99 false 1.073,1.135 0.667,0.938 false 2.469,0.188 2.677,0.385 0.208,0.198 10 false *A 0.635,0.219 0.844,0.385 0.208,0.167 10 false *B 2.594,0.51 2.75,0.688 0.156,0.177 10 false *a 0.979,0.51 1.146,0.677 0.167,0.167 10 false *b 0.49,0.823 0.646,0.969 0.156,0.146 10 false *c 3.031,0.865 3.188,1.01 0.156,0.146 10 false *c
*A Front Side
*B Rear Side
*a 4.57 mm (0.180 in.)
*b 4.8 mm (0.189 in.)
*c Edge of curved surface


Using a plastic hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.

NOTICE:

To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.



Hide 68103 24.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B287024

Slide the rear door glass sub-assembly to install it as shown in the illustration.


Hide 68123B 25.INSTALL REAR DOOR QUARTER WINDOW GLASS

a.

Install the rear door quarter window glass to the rear door quarter window weatherstrip.


b.
B287025

Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


Hide 67407F 26.INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

a.
B286994

Install the rear door lower window frame sub-assembly with the screw and 2 bolts.


Hide 68142C 27.INSTALL REAR DOOR GLASS RUN

a.
B286993

Install the rear door glass run.


Hide 67871 28.INSTALL REAR DOOR WEATHERSTRIP

a.
B286992

Engage the 20 clips to install the rear door weatherstrip.


Hide 68630D 29.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door check assembly.


b.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
B286991

Install the rear door check assembly with the 2 nuts and bolt.

Torque:
Bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67841E 30.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the rear door panel.


b.
B287026C03
0.406,0.469 0.552,0.5 true 2.865,0.344 3.021,0.271 false 2.094,3.156 1.938,3.042 false 0.25,0.375 0.49,0.563 0.24,0.188 10 false *1 3.052,0.167 3.281,0.333 0.229,0.167 10 false *1 2.104,3.073 2.417,3.281 0.313,0.208 10 false *1
*1 Reference Point


Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.


c.

Attach the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



d.

Connect the connector.


Hide 68173B 31.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

a.
B287027

Install the rear door inner glass weatherstrip.


Hide 69205A 32.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B286988

Engage the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.


Hide 67603 33.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B287028

Install the No. 1 door scuff plate clamp as shown in the illustration.


b.
B287029C02
0.635,0.688 0.792,0.688 0.792,0.688 0.865,1.083 false 0.958,1.49 1.094,1.75 false 0.458,0.604 0.625,0.76 0.167,0.156 10 false *1 1.031,1.771 1.198,1.927 0.167,0.156 10 false *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly


Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.


c.

Connect the connector.


d.

Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

B349451C01
4.51,1.885 4.708,2.208 false 4.667,2.25 4.979,2.448 0.313,0.198 10 false *1
*1 Reference Boss - -



e.
B286984

Engage the 8 clips and install the rear door trim board sub-assembly.


f.

Install the 3 screws.


g.

If protective tape has been applied, remove it.


Hide 74250 34.INSTALL REAR ARMREST ASSEMBLY

a.
B287031

Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.


Hide 35.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.

Connect the connector.


b.
B287032

Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.


Hide 69283A 36.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B287033

Engage the 3 claws to install the rear door inside handle bezel plug.


Hide 37.CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64718C 38.INSTALL LUGGAGE TRIM SERVICE HOLE COVER