Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A78-121  Drive Motor "A" Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0D2F-266).

If an overvoltage occurs in the motor inverter or generator inverter, the MG ECU detects it and transmits this information to the power management control ECU.

HINT:

The term "drive motor A" indicates MG2.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A78-121 Drive Motor "A" Inverter Performance Motor inverter overvoltage signal detection (overvoltage due to system malfunction)
·

Hybrid battery junction block assembly

·

Inverter with converter assembly

·

Service plug grip (EV battery fuse)

·

No. 4 floor wire

·

Hybrid vehicle transaxle assembly

·

Power management control ECU

·

INV fuse

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P1CAC-200 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1CAC-200).

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

Refer to the wiring diagram for DTC P324E-788 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P324E-788).

Refer to the wiring diagram for DTC U0110-159 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>U0110-159).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0A78-121 is set before any of the DTCs in the table below are set. A
Any of the DTCs in the table below are set before P0A78-121 is set. B


DTC No. Relevant Diagnosis
P0A9C-123 Hybrid Battery Temperature Sensor "A" Range / Performance
P0A9D-123 Hybrid Battery Temperature Sensor "A" Circuit Low
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High
P0AC6-123 Hybrid Battery Temperature Sensor "B" Range / Performance
P0AC7-123 Hybrid Battery Temperature Sensor "B" Circuit Low
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High
P0ACB-123 Hybrid Battery Temperature Sensor "C" Range / Performance
P0ACC-123 Hybrid Battery Temperature Sensor "C" Circuit Low
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P3011-123, P3012-123, P3013-123, P3014-123, P3015-123, P3016-123, P3017-123, P3018-123, P3019-123, P3020-123, P3021-123, P3022-123, P3023-123, P3024-123, P3025-123, P3026-123, P3027-123 Battery Block # Becomes Weak
P3065-123 Hybrid Battery Temperature Sensor Range / Performance Stuck A
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

HINT:
·

Refer to the Freeze Frame data to determine the order in which the DTCs were set.

·

P0A78-121 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0A78-121 only is output A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P06B0-163 Sensor Power Supply "A" Circuit / Open
P06D6-511 Sensor Reference Voltage "F" Circuit / Open
P06E6-164 Sensor Power Supply "C" Circuit / Open
P0A1A-151, 166, 517, 658, 791, 809 Generator Control Module
P0A1B-198, 503, 505, 547, 554, 786, 794, 806 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500, 504, 506, 549, 556, 808 Drive Motor "A" Position Sensor Circuit Range / Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513, 518, 811 Generator Position Sensor Circuit Range / Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A78-113, 128, 279, 284, 286, 287, 548, 555, 807 Drive Motor "A" Inverter Performance
P0A7A-122, 130, 322, 324, 325, 810 Generator Inverter Performance
P0A90-509 Drive Motor "A" Performance
P0A92-521 Hybrid Generator Performance
P0A93-346 Inverter Cooling System Performance
P0A94-172, 553, 557 DC / DC Converter Performance
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0BEA-290 Drive Motor "A" Phase V Current Sensor Circuit Range / Performance
P0BEE-298 Drive Motor "A" Phase W Current Sensor Circuit Range / Performance
P0C19-306 Drive Motor "A" Torque Delivered Performance
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
P0C76-523 Hybrid Battery System Discharge Time Too Long
P0CA3-442 DC/DC Converter Step Up Voltage Performance
P0D2E-565, 586 Drive Motor "A" Inverter Voltage Sensor Circuit Range / Performance
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Voltage Sensor Circuit High
P0E05-328 Generator Phase V Current Sensor Circuit Range / Performance
P0E09-336 Generator Phase W Current Sensor Circuit Range / Performance
P0E32-585 DC/DC Converter Voltage Sensor "A" Range / Performance
P0E33-589 DC/DC Converter Voltage Sensor "A" Low
P0E34-590 DC/DC Converter Voltage Sensor "A" High
P0E71-344 Generator Torque Delivered Performance
P1C2A-155 Generator A/D Converter Circuit
P1C2B-192 Drive Motor "A" A/D Converter Circuit
P1C2D-587 Hybrid Battery Voltage / DC/DC Converter Voltage Correlation
P1C3C-294 Drive Motor "A" Phase V Current Sensor Correlation
P1C3D-302 Drive Motor "A" Phase W Current Sensor Correlation
P1C3E-333 Generator Phase V Current Sensor Correlation
P1C3F-341 Generator Phase W Current Sensor Correlation
P1C4A-288 Drive Motor "A" Phase V Current Sensor Sub Circuit Range / Performance
P1C4F-296 Drive Motor "A" Phase W Current Sensor Sub Circuit Range / Performance
P1C54-326 Generator Phase V Current Sensor Sub Circuit Range / Performance
P1C59-334 Generator Phase W Current Sensor Sub Circuit Range / Performance
P1C6D-501 Drive Motor "A" Phase V Current Sensor Offset Range / Performance
P1C6E-502 Drive Motor "A" Phase W Current Sensor Offset Range / Performance
P1C71-515 Generator Phase V Current Sensor Offset Range / Performance
P1C72-516 Generator Phase W Current Sensor Offset Range / Performance
P1C73-512 Sensor Standard Voltage "F" Circuit / Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P1CAC-200 Generator Position Sensor Angle Malfunction
P1CAD-168 Drive Motor "A" Position Sensor Angle Malfunction
P1CAF-792 Generator Position Sensor REF Signal Cycle Malfunction
P1CB0-795 Drive Motor "A" Position Sensor REF Signal Cycle Malfunction
P1CB2-793 Generator Position Sensor REF Signal Stop Malfunction
P1CB3-796 Drive Motor "A" Position Sensor REF Signal Stop Malfunction
P3004-803 High Voltage Power Resource
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator
P314A-828 Inverter Coolant Pump Speed Signal

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A78-121 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

OK

5.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK GENERATOR RESOLVER

OK

6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

25.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

7.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK MOTOR RESOLVER

OK

8.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

NG

27.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
8.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

A

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

12.CHECK INVERTER WITH CONVERTER ASSEMBLY (NO. 4 FLOOR WIRE CONNECTOR CONNECTION CONDITION)

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

12.CHECK INVERTER WITH CONVERTER ASSEMBLY (NO. 4 FLOOR WIRE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259710

Remove the connector cover assembly from the inverter with converter assembly.


c.
A259712E07
1.583,0.979 1.865,1.177 0.281,0.198 1.656,1 1.854,1.156 0.198,0.156 8 false Q1

Check that the bolt for the No.4 floor wire is tightened to the specified torque, the No.4 floor wire is connected securely, and there are no contact problems.

Specified Condition:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)



d.

Disconnect connector Q1 of the No .4 floor wire from the inverter with converter assembly.


e.

Check for arc marks at the bolt and terminals for the No. 4 floor wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the No. 4 floor wire to the inverter with converter assembly.


g.

Install the connector cover assembly.



A

13.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

13.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Visually check the connection of the service plug grip to the HV battery. Remove the service plug grip and check for contamination.

OK:

Dirt or foreign objects have not entered the connection, and there is no evidence of contamination.


Result:
Proceed to
OK
NG




OK

14.INSPECT SERVICE PLUG GRIP

NG

14.INSPECT SERVICE PLUG GRIP
a.

Remove the service plug grip.


b.
A204559C03
0.125,0.098 0.318,0.263 0.193,0.166 10 *1
*1 Service plug grip


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Service plug grip terminals Always Below 1 Ω



c.

Install the service plug grip.

Result:
Proceed to
OK
NG




OK

15.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (NO. 4 FLOOR WIRE CONNECTION CONDITION)

NG

15.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (NO. 4 FLOOR WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 4 hybrid battery shield panel.


c.
A259723N06
0.281,0.604 0.771,0.896 0.49,0.292 1.688,0.177 2.177,0.469 0.49,0.292 0.417,0.656 0.667,0.854 0.25,0.198 10 true Q3 1.854,0.229 2.052,0.406 0.198,0.177 10 true Q2

Check that the No. 4 floor wire connectors are connected securely, and there are no contact problems.


d.

Disconnect connector Q2 and connector Q3 of the No. 4 floor wire from the hybrid battery junction block assembly.


e.

Check for arc marks on the terminals of the No. 4 floor wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the No. 4 floor wire to the hybrid battery junction block assembly.


g.

Install the No. 4 hybrid battery shield panel.



A

16.CHECK NO. 4 FLOOR WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

16.CHECK NO. 4 FLOOR WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 4 hybrid battery shield pedal (See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A259723N06
0.281,0.604 0.771,0.896 0.49,0.292 1.688,0.177 2.177,0.469 0.49,0.292 0.417,0.656 0.667,0.854 0.25,0.198 10 true Q3 1.854,0.229 2.052,0.406 0.198,0.177 10 true Q2

Disconnect connectors Q2 and Q3 of the No. 4 floor wire from the hybrid battery junction block assembly.


d.
A259710

Remove the connector cover assembly from the inverter with converter assembly.


e.
A259712N04
1.5,0.865 1.99,1.156 0.49,0.292 1.667,0.917 1.927,1.094 0.26,0.177 10 true Q1

Disconnect connector Q1 of the No. 4 floor wire from the inverter with converter assembly.


f.
A258639C01
0.51,1.438 0.875,1.677 0.365,0.24 1.708,2.385 2.073,2.625 0.365,0.24 0.917,2.385 1.281,2.625 0.365,0.24 1.302,1.708 1.156,1.958 false 1.781,1.708 1.948,1.969 false 1.073,3.042 0.938,3.292 false 1.875,3.042 2.042,3.292 false 2,4.052 1.698,4.271 false 0.26,0.125 0.542,0.302 0.281,0.177 10 *a 0.26,2.729 0.552,2.958 0.292,0.229 10 *b 1.031,1.979 1.365,2.167 0.333,0.188 10 CBI 1.844,1.979 2.177,2.208 0.333,0.229 10 CEI 0.604,1.469 0.813,1.688 0.208,0.219 10 Q1 1.813,2.438 2.083,2.667 0.271,0.229 10 Q3 1.021,2.438 1.271,2.646 0.25,0.208 10 Q2 0.813,3.302 1.146,3.521 0.333,0.219 10 CBI 1.938,3.302 2.24,3.531 0.302,0.229 10 CEI 1.49,4.219 1.74,4.417 0.25,0.198 10 *1
*1 Shield Ground
*a Frame Wire (Inverter with Converter Assembly Side)
*b Frame Wire (Hybrid Battery Junction Block Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q1-1 (CBI) - Q2-1 (CBI)
(Positive terminal)
Power switch off Below 1 Ω
Q1-2 (CEI) - Q3-1 (CEI)
(Negative terminal)
Power switch off Below 1 Ω



g.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q2-1 (CBI) - Body ground and shield ground Power switch off 10 MΩ or higher
Q3-1 (CEI) - Body ground and shield ground Power switch off 10 MΩ or higher
Q2-1 (CBI) - Q3-1 (CEI) Power switch off 10 MΩ or higher



h.

Connect the No. 4 floor wire to the hybrid battery junction block assembly.


i.

Connect the No. 4 floor wire to the inverter with converter assembly.


j.

Install the connector cover assembly.


k.

Install the No. 4 hybrid battery shield panel.

Result:
Proceed to
OK
NG




OK

17.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

17.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
A306036C01
1.063,0.26 1.365,0.51 0.302,0.25 2.958,0.76 3.26,1.01 0.302,0.25 0.146,2.333 0.448,2.583 0.302,0.25 0.406,0.688 0.719,0.813 false 2.76,1.208 3.073,1.333 false 0.875,2.969 1.188,2.542 false 1.583,2.969 1.385,2.542 false 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 0.146,0.615 0.458,0.813 0.313,0.198 10 false CBI 1.125,0.302 1.438,0.5 0.313,0.198 10 false Q2 3.063,0.802 3.375,1 0.313,0.198 10 false A 3.115,1.292 3.427,1.49 0.313,0.198 10 false + 0.219,2.375 0.531,2.573 0.313,0.198 10 false O9 0.708,3.01 1.292,3.25 0.583,0.24 10 false GND 1.375,3.021 1.958,3.26 0.583,0.24 10 false SMRB
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (+) - Q2-1 (CBI) Auxiliary battery voltage is not applied between terminals O9-1 (SMRB) and O9-2 (GND) 10 kΩ or higher
Auxiliary battery voltage is applied between terminals O9-1 (SMRB) and O9-2 (GND) Below 1 Ω



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-1 (SMRB) - O9-2 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω



e.

Install the hybrid battery junction block assembly.

Result:
Proceed to
OK
NG




OK

18.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

18.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
A306037C01
0.104,1 0.417,1.219 0.313,0.219 2.938,1.615 3.25,1.833 0.313,0.219 0.229,2.375 0.542,2.594 0.313,0.219 0.781,0.948 1.198,0.531 false 2.677,1.479 3.094,1.063 false 0.625,2.958 1.052,2.531 false 1.615,2.917 1.24,2.542 false 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.177,1.021 0.49,1.219 0.313,0.198 10 false Q3 1.125,0.333 1.677,0.563 0.552,0.229 10 false CEI 3.104,0.885 3.417,1.063 0.313,0.177 10 false - 3.021,1.635 3.333,1.833 0.313,0.198 10 false q1 0.375,2.979 0.958,3.208 0.583,0.229 10 false SMRG 1.49,2.969 2.073,3.198 0.583,0.229 10 false GND 0.292,2.406 0.604,2.604 0.313,0.198 10 false O9
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
q1-1 (-) - Q3-1 (CEI) Auxiliary battery voltage is not applied between terminals O9-3 (SMRG) and O9-2 (GND) 10 kΩ or higher
Auxiliary battery voltage is applied between terminals O9-3 (SMRG) and O9-2 (GND) Below 1 Ω



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-3 (SMRG) - O9-2 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω



e.

Install the hybrid battery junction block assembly.

Result:
Proceed to
OK
NG




OK

19.CHECK FUSE (INV)

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

19.CHECK FUSE (INV)

OK

20.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

29.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - INV FUSE)
20.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

OK

21.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

21.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

OK

22.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK POWER MANAGEMENT CONTROL ECU

OK

23.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

23.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

24.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

24.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

CONNECT SECURELY

25.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

26.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

26.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

28.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

CONNECT SECURELY

28.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - INV FUSE)

OK

30.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

31.REPAIR OR REPLACE HARNESS OR CONNECTOR
30.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

REPLACE FUSE (INV)

31.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV)