Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here



1. INSTALL AIR CONDITIONING UNIT ASSEMBLY


  1. Install the air conditioning unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


    E235219E01

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration to install the air conditioning unit assembly.



2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT

NOTICE:
  1. Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
  2. When installing the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



  1. Disengage the 3 guides and temporarily install the instrument panel reinforcement assembly with air conditioning unit as shown in the illustration.


    E234638

  1. Install the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the cooler drain hose as shown in the illustration.

    NOTICE:
    Connect the cooler drain hose firmly to prevent coolant leaks.



  1. Install the instrument panel reinforcement assembly with the 3 bolts <A> and 2 new bolts <B>.


    E234639E01


    Text in Illustration 
    *1
    Movable Collar
    *2
    Body
    *3
    Instrument Panel Reinforcement
    -
    -
    *a
    Step 1
    *b
    Step 2
    *c
    Step 3
    *d
    Step 4

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration to install the reinforcement assembly.

  1. Install the instrument panel reinforcement assembly with air conditioning unit with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    E227180E01
  1. Install the 2 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the 2 bolts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. Engage each clamp.

  1. Connect the connector.

  1. Install the 2 nuts and connect the connector holder.

  1. Install the bolt and connect the earth wire.

  1. Engage each clamp.

  1. Connect the connector.

  1. Install the 2 bolts and connect the 2 earth wires.

  1. Engage each clamp.



    E231353
  1. Pass the cooler drain hose through the vehicle securely.

    NOTICE:
    Connect the cooler drain hose firmly to prevent water leaks.

  1. Engage each clamp.

  1. Connect the connector.

  1. Engage each clamp.



  1. Engage the claw and connect the airbag connector as shown in the illustration.


    E227176



    E227174E01
  1. Engage the 2 claws to lock the retainer as shown in the illustration.
    Text in Illustration 
    *1
    Retainer



  1. for LHD:

    1. Connect the connector.

    2. Install the bolt.

      Torque:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    3. Install the shift lever support with the 4 bolts.

      Torque:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    4. Check that the park/neutral position switch and the shift lever are in N.



    5. C244005E03
    6. Install the lower shift lever assembly with the 4 bolts in the order shown in the illustration.

      Torque:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    7. C194520E03
    8. Slide the slider of the transmission control cable assembly in the direction indicated by the arrow and pull the lock piece outward.
      Text in Illustration 
      *1
      Slider
      *2
      Lock Piece
      *a
      Slide
      *b
      Pull



    9. C239661E01
    10. Install the end of the transmission control cable assembly to the lower shift lever assembly.
      Text in Illustration 
      *1
      Lock Piece

      NOTICE:
      1. Check that the lock piece is pulled up.
      2. Install the cable end all the way to the base of the pin.

    11. Push the lock piece into the adjuster case.

      NOTICE:
      1. Check that the park/neutral position switch and the shift lever are in neutral.
      2. Securely push in the lock piece until the slider lock is engaged.



    E235220E01
  1. Connect each connector.
    Text in Illustration 
    *1
    Center Airbag Sensor Connector

  1. Engage the 3 clamps.

  1. Connect the center airbag sensor connectors to the center airbag sensor assembly as shown in the illustration.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.



    E227170
  1. Engage the 3 claws to close the 3 clamps as shown in the illustration.

  1. for RHD:

    1. Connect the connector.

    2. Install the bolt.

      Torque:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }



3. INSTALL FRONT LOWER PANEL PACKING


    E227178
  1. Install the 2 front lower panel packings shown in the illustration.



4. INSTALL INSTRUMENT PANEL SAFETY PAD CAP


    E227872E01
  1. Install the 5 new instrument panel safety pad caps.
    Text in Illustration 
    *A
    for Driver Side
    *B
    for Passenger Side



5. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
  1. Install the screw and 2 nuts.

  1. Install the No. 2 instrument panel brace sub-assembly with the bolt and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the earth wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Engage each clamp.

  1. Connect the connector.



6. INSTALL INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
  1. Install the screw and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the instrument panel to cowl brace sub-assembly with the bolt and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the earth wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Engage each clamp.

  1. Connect each connector.



7. INSTALL NO. 1 CONSOLE BOX DUCT
  1. Install the No. 1 console box duct with the clip.



8. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET
  1. Install the No. 1 console mounting bracket with the screw.



9. INSTALL REAR NO. 3 AIR DUCT
  1. Engage the 2 claws to install the rear No. 3 air duct.



10. INSTALL FLOOR CARPET BRACKET LH
  1. Engage the 2 guides.

  1. Install the floor carpet bracket LH with the 2 clips.



11. INSTALL REAR NO. 4 AIR DUCT


    E227158
  1. Engage the 4 claws to install the rear No. 4 air duct as shown in the illustration.



    E227459
  1. Engage the guide to install the floor carpet to the original position as shown in the illustration.



    E227151
  1. Engage the guide to connect the fuel lid lock open lever sub-assembly as shown in the illustration.

  1. Install the screw.



12. CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    E227151
  1. Engage the guide to connect the fuel lid lock open lever sub-assembly as shown in the illustration.

  1. Install the screw.



13. INSTALL REAR NO. 1 AIR DUCT
  1. Engage the 2 claws to install the rear No. 1 air duct.



14. INSTALL FLOOR CARPET BRACKET RH
  1. Engage the 2 guides.

  1. Install the floor carpet bracket RH with the 2 clips.



15. INSTALL REAR NO. 2 AIR DUCT


    E227876
  1. Engage the 4 claws to install the rear No. 2 air duct as shown in the illustration.



    E229495
  1. Engage the guide to install the floor carpet to the original position as shown in the illustration.



16. INSTALL FLOOR CARPET HOOK
  1. Engage the 6 claws to install the 6 floor carpet hooks.

  1. Engage the 6 guides.



17. INSTALL WINDSHIELD WIPER RELAY ASSEMBLY
  1. Install the windshield wiper relay assembly with the nut.

  1. Connect the connector.



18. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Engage the 2 guides.

  1. Install the air conditioning amplifier assembly with the 2 screws.

  1. Connect each connector.



19. INSTALL ECU INTEGRATION BOX RH
  1. Install the ECU integration box RH with the 2 nuts and bolt.

    Torque:
    Bolt:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
    Nut:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect each connector.



20. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    B279023
  1. Engage the claw to connect the connector as shown in the illustration.

    NOTICE:
    Be sure to engage the connector securely.



    B279021
  1. Engage the claw to lock the connector lock as shown in the illustration.



    B279019
  1. Engage the claw to connect the connector as shown in the illustration.

    NOTICE:
    Be sure to engage the connector securely.

  1. for LHD:

    1. Install the instrument panel junction block assembly with the bolt and 2 nuts.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    2. Connect the 5 connectors.

      NOTICE:
      Be sure to engage each connector securely.

  1. for RHD:

    1. Engage the claw to install the wiring harness clamp bracket.

    2. Install the nut.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    3. Install the instrument panel junction block assembly with the bolt and nut.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    4. Connect the 5 connectors.

      NOTICE:
      Be sure to engage each connector securely.



21. INSTALL POWER MANAGEMENT CONTROL ECU


    B293920E01
  1. Install the power management control ECU with the 2 nuts in the order shown in the illustration.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 4 connectors.



22. INSTALL STEERING POST ASSEMBLY
(Click here)


23. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
(Click here)


24. INSTALL FRONT SEAT ASSEMBLY LH
(Click here)


25. INSTALL FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



26. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
  1. Remove the vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and fitting surface of the air conditioner tube and accessory assembly.

    Compressor oil:
    ND-OIL 11 or equivalent

  1. Install the O-ring to the air conditioner tube and accessory assembly.

  1. Connect the air conditioner tube and accessory assembly.



27. CONNECT SUCTION PIPE SUB-ASSEMBLY
  1. Remove the vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

    Compressor oil:
    ND-OIL 11 or equivalent

  1. Install the O-ring to the suction pipe sub-assembly.



    E227143
  1. Move the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



28. CONNECT HEATER INLET WATER HOSE
  1. Using pliers, grip the claws of the clip and slide the clip to connect the inlet water hose.



29. CONNECT HEATER OUTLET WATER HOSE
  1. Using pliers, grip the claws of the clip and slide the clip to connect the heater outlet water hose.



30. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



31. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



32. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


33. ADD COOLANT (for Engine)
  1. Tighten the radiator drain cock plug by hand.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
    Item
    Capacity
    Engine coolant
    7.2 liters (7.6 US qts, 6.3 lmp. qts)

    NOTICE:
    Never use water as a substitute for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reserve tank cap.

  1. Put the engine in inspection mode (Click here).

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to the low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

    2. Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the cooling fans.

      NOTICE:
      1. Make sure that the radiator reserve tank assembly still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reserve tank assembly does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reserve tank assembly is filled to the full line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the full line on the radiator reserve tank assembly.



34. INSPECT FOR COOLANT LEAK (for Engine)

NOTICE:
Before performing each inspection, turn the A/C switch off.



    A255285
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



35. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump or appropriate equipment.



  1. Charge the air conditioning system with refrigerant.

    Refrigerant type:
    HFC-134a (R134a)



    E143108E11


    Text in Illustration 
    *a
    Sub-cool System
    *b
    High Pressure
    *c
    Refrigerant Amount
    *d
    Standard charge amount
    *e
    Charge additional 100 g (3.5 oz.)
    *f
    Point where bubbles disappear
    *g
    Mean value in proper range
    *h
    Overcharged

    Standard charge amount:
    480 to 580g (16.9 to 20.4oz.)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to work without refrigerant, resulting in overheating of the compressor.
    2. The refrigerant amount should be checked by quantity (weight).

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.



36. WARM UP COMPRESSOR
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing air conditioning system lines (including the compressor).



37. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Power switch off.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases which are not refrigerant, such as gasoline vapor and exhaust gas).
    3. Repeat the inspection 2 or 3 times.
    4. Measure the pressure to make sure that there is some refrigerant remaining in the air conditioning system.
      Pressure when the compressor is off: approx. 392 to 588 kPa (3.9 to 5.9 kgf/cm2, 57 to 85 psi)



    I042222E40
  1. Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Inspect for Leak



    N014519E08
  1. Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *2
    Drain Hose

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
    2. Bring the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow checking for leaks.

  1. If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.

  1. Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.

    HINT:
    When checking for leaks, the presence of oily dirt at a joint can indicate a leak.



38. INITIALIZATION SERVO MOTOR
(Click here)