DTC C1246 Master Cylinder Pressure Sensor Malfunction |
DTC C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) |

| DTC No. | DTC Detection Condition | Trouble Area |
| C1246 | Any of the following is detected:
|
|
| C1281 | Detected only during Test Mode. |
|
| 1.CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
| Brake pedal depressed. | ON |
| Brake pedal released. | OFF |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Master Cylinder Sensor | Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.20 to 0.40 V | Reading increases when brake pedal is depressed |
Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the intelligent tester changes when the brake pedal is depressed.
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH) |
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch / ON or OFF | ON: Brake pedal depressed beyond a specified point OFF: Brake pedal not depressed beyond a specified point | - |
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.
Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn on.
| Result | Proceed to |
| OK | A |
| NG (The stop light switch does not turn on.) | B |
| NG (Turning on of the brake pedal load sensing switch is not confirmed.) | C |
| NG (The brake pedal load sensing switch turns on first.) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 4.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
At a speed of 30 km/h (18 mph) or more, drive the vehicle and perform a braking test (decelerate the vehicle by depressing the brake pedal).
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1246 is not output. | A |
| DTC C1246 is output. | B |
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (STP TERMINAL) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-30 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| A49-30 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | ||
| ||
| 6.INSPECT BRAKE PEDAL LOAD SENSING SWITCH |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the brake pedal load sensing switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (FSW+) - 1 (FSW-) | Switch OFF (Brake pedal depressed) | 950 to 1050 Ω |
| 2 (FSW+) - 1 (FSW-) | Switch ON (Brake pedal released) | 203 to 223 Ω |
| *a | Component without harness connected (Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly)) |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-34 (FSW+) - A40-2 (FSW+) | Always | Below 1 Ω |
| A49-34 (FSW+) - Body ground | Always | 10 kΩ or higher |
| A40-1 (FSW-) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 8.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch assembly installation (Click here for LHD or Click here for RHD).
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||