Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows) > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

When the engine switch is on (IG), the power window regulator motor assembly (for rear RH door) is operated by the rear power window regulator switch assembly (for RH door).

WIRING DIAGRAM


B363309E08


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. Check that the window lock switch is off before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR) - BATTERY)
  1. Disconnect the L7 rear power window regulator switch assembly (for RH door) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L7-2 (B) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)
  1. Remove the rear power window regulator switch assembly (for RH door) (Click here).

  1. Inspect the rear power window regulator switch assembly (for RH door) (Click here).



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR))
  1. Disconnect the L6 power window regulator motor assembly (for rear RH door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L7-7 (U) - L6-1 (U)
    Always
    Below 1 Ω
    L7-7 (U) or L6-1 (U) - Body ground
    Always
    10 kΩ or higher
    L7-1 (D) - L6-2 (D)
    Always
    Below 1 Ω
    L7-1 (D) or L6-2 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Remove the power window regulator master switch assembly (Click here).

  1. Inspect the power window regulator master switch assembly (Click here).



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K15-10 (RRU) - L7-3 (SU)
    Always
    Below 1 Ω
    K15-10 (RRU) or L7-3 (SU) - Body ground
    Always
    10 kΩ or higher
    K15-16 (RRD) - L7-4 (SD)
    Always
    Below 1 Ω
    K15-16 (RRD) or L7-4 (SD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR REAR RH DOOR) (Click here)