Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows) > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

When the engine switch is on (IG), the power window regulator motor assembly (for front passenger door) is operated by the power window regulator switch assembly. The power window regulator motor assembly (for front passenger door) has motor, regulator, and ECU functions.

WIRING DIAGRAM


B363308E04


INSPECTION PROCEDURE

NOTICE:
  1. The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (Click here).
  2. If the power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system (Click here).
  3. Check that the window lock switch is off before performing the following procedure.
  4. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  5. If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

1.READ VALUE USING GTS (MAIN BODY)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Communication P-Door Motor
    Connection status between power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU) / STOP or OK
    STOP: Communication stopped
    OK: Normal communication
    -

    OK:
    On the GTS screen, OK is displayed.



NG
GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) (Click here)
OK


2.READ VALUE USING GTS (P-DOOR MOTOR)
  1. Enter the following menus: Body Electrical / P-Door Motor / Data List.

  1. Read the Data List according to the display on the GTS.

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Up SW
    Front Passenger door power window manual up switch signal / OFF or ON
    OFF: Front passenger door power window manual up switch not being operated
    ON: Front passenger door power window manual up switch being operated
    -
    P Door P/W Down SW
    Front Passenger door power window manual down switch signal / OFF or ON
    OFF: Front passenger door power window manual down switch not being operated
    ON: Front passenger door power window manual down switch being operated
    -

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST USING GTS (P-DOOR MOTOR)
  1. Enter the following menus: Body Electrical / P-Door Motor / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


    P-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / DOWN / UP
    -

    OK:
    Front passenger door power window operates normally.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
  1. Remove the power window regulator switch assembly (Click here).

  1. Inspect the power window regulator switch assembly (Click here).



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) AND BODY GROUND)
  1. Disconnect the J9 power window regulator motor assembly (for front passenger door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J12-5 (UP) - J9-10 (UP)
    Always
    Below 1 Ω
    J12-5 (UP) or J9-10 (UP) - Body ground
    Always
    10 kΩ or higher
    J12-4 (DOWN) - J9-7 (DOWN)
    Always
    Below 1 Ω
    J12-4 (DOWN) or J9-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J12-7 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)